essons / Various / ENGINEERING FACULTY a) V1= b) Q1= c) Q2= The end of the pipe with a diameter of 150 mm shown in the figure is divided into two branches, and water flows into the atmosphere from the branches. The system is in the horizontal plane. If V 2 =V 3 =12 m/s, calculate the following requirements without considering the frictions. (D₁ =150mm, D2 100mm, D3 75mm m/s m3/h 3 m3/h 150 30⁰ -3

essons / Various / ENGINEERING FACULTY a) V1= b) Q1= c) Q2= The end of the pipe with a diameter of 150 mm shown in the figure is divided into two branches, and water flows into the atmosphere from the branches. The system is in the horizontal plane. If V 2 =V 3 =12 m/s, calculate the following requirements without considering the frictions. (D₁ =150mm, D2 100mm, D3 75mm m/s m3/h 3 m3/h 150 30⁰ -3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Fluid mechanics, i need solutions in 10 minutes please. Q/Q2 The 4 -m- diameter circular gate of Fig. E2.6a is located in the inclined wall of a large reser voir containing water (y = 9.80 kN / m³). The gate is mounted on a shaft along its horizon tal diameter. For a water depth of 10 m above the shaft determine: (a) the magnitude and lo cation of the resultant force exerted on the gate by the water, and (b) the moment that would have to be applied to the shaft to open the gate.
Question-02:(CLO2)(10)A closed container containing water up to a height of 3.0 meter and air at the upper part with an orifice of 100 mm at its bottom. If 50% of the air is being removed from the upper part of the container by suction then Estimatedischarge passing through the orifice using Bernoulli’s equation if Cd=0.62.
Water flows upwards through a venturi section. The venturi section varies indiameter from 15cm at the top and bottom to 5cm at the narrowest point. A differential pressuretransducer measured a pressure difference of 43kPa. Assuming steady flow, determine the velocity ofthe flow through the narrowest region and the discharge through the meter. Assume that water has adensity of 1g/cm 3 .b) The discharge through the venturi section
If the quantity of air discharged at D is 1,500 m3/min and friction factor of 0.0048, calculate the following: (a) the quantity of air discharged at C; (b) static pressure at fan outlet A. Group of answer choices 3203.2 m3/min; 14.75 N/m2 2203.2 m3/min; 24.75 N/m2 2203.2 m3/min; 14.75 N/m2 4203.2 m3/min; 14.75 N/m2please show complete solution for review and analysis purposes
Water flows upwards through a venturi section. The venturi section varies indiameter from 15cm at the top and bottom to 5cm at the narrowest point. A differential pressuretransducer measured a pressure difference of 43kPa. Assuming steady flow, determine the velocity ofthe flow through the narrowest region and the discharge through the meter. Assume that water has adensity of 1g/cm 3 .c) Is the fluid pressure at the bottom of the venturi section greater than, less than, or equal to the fluidpressure at the narrowest region?
Water flows upwards through a venturi section. The venturi section varies indiameter from 15cm at the top and bottom to 5cm at the narrowest point. A differential pressuretransducer measured a pressure difference of 43kPa. Assuming steady flow, determine the velocity ofthe flow through the narrowest region and the discharge through the meter. Assume that water has adensity of 1g/cm 3 .a) The mean fluid velocity through the narrowest region
Fluid mechanics, i need solutions in 10 minutes please. MCQ/The submerged sector gate AB shown in the figure is 1/9 of a circle radius 4 m. The length of the gate is 10 m. Determine the horizontal component of water pressure acting on the gate. A-262.874 kN B-162.328 KN C-324.260 KN D- 448.161 KN E- 591.263 KN F-392.273 kN G- 89.207 kN H-536.078 KN I-208.119 KN J- 490.984 kN K- 127.908 KN L- 113.001 KN
A 75 mm horizontal pipe of circular cross section conveying water under a pressure of 0.75bars has its diameter reduced from 75 mm to 2 mm by means of a short transition 30 mm in length. The pipe empties into the atmosphere. The discharge is 0.14m3.s-1, what is the percentage change in mean velocities? The pipe is anchored to a pillar with the anchoring having a factor of safety of 1.5. What force must the anchor withstand to achieve the above?
Water is flowing under a sluice gate in a horizontal rectangular channel that is 4.5meters wide. The depths Yo (depth behind the sluice gate) is 6m and Y1 (after the sluice gate) is 0.80 meter. What will be the horsepower lost in the hydraulic jump?
The diving bell has the shape of a frustum of a cone (circular) with a closed flat top and open bottom. It is lowered from the outside air into salt water (ɣ= 10.2 kN/m3). Compute the volume of air trapped inside the caisson when the water level has risen 2.50m inside? Unit of the Correct Answer: m3 Decimal Places required in the final answer: 3
Completely solve. Write legibly. Box the final answer. Water is flowing through a pipe 1/3 ft. inside diameter into a pipe 1'' in diameter at a rate of 12.62 lps. If the pressure in the 4'' pipe is 275.8 kPa, what is the pressure in the small pipe assuming no energy loss and friction head loss?
A 1.5m square tank, 3m tall is drained by a 25mm-diameter orifice located at its bottom. If the tank is initially filled with water, how deep is the water in the tank after 45 minutes? Assume C=0.62