The speed of water passing through the elbow on a buried pipe is V = 8 ft/s. Assume water is ideal fluid, that is, incompressible and frictionless. (Figure 1) B 5 in. 8 ft/s Assuming that the pipe connections at A and B do not offer any force resistance on the elbow, determine the resultant horizontal force F that the support must exert on the elbow in order to hold it in equilibrium. The pressure within the pipe at A and Bis 11 psi

The speed of water passing through the elbow on a buried pipe is V = 8 ft/s. Assume water is ideal fluid, that is, incompressible and frictionless. (Figure 1) B 5 in. 8 ft/s Assuming that the pipe connections at A and B do not offer any force resistance on the elbow, determine the resultant horizontal force F that the support must exert on the elbow in order to hold it in equilibrium. The pressure within the pipe at A and Bis 11 psi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the horizontal and vertical component of the total hydrostatic force (kN) the oil exerts on the face AB of the overhang if it is 1.31 m long. Oil is 0.8
Obtain the gage pressure at the center A of the pipe shown. Neglect surface tension effects. For Liquid 1 specific gravity= 1.5, for liquid 2 specific gravity= 3.2, h1=15cm, h2= 30cm,h3=75cm
A parabolic gate AB is 7 meters perpendicular . Determine the following : 1. Compute the horizontal component of the hydrostatic force acting on gate AB. 2. Compute the vertical component of the hydrostatic force acting on the gate AB. 3. Compute the force at A that is required to prevent rotation about the hinged at B. Note: Always consider the height of the water when determining the pressure .
A 3-cm-diameter horizontal pipe attached to a surface makes a 90° turn to a vertical upward direction before the water is discharged at a velocity of 6 m/s. The horizontal section is 5 m long and the vertical section is 4 m long. Neglecting the mass of the pipe and considering the weight of the water contained in the pipe, the bending moment acting on the base of the pipe on the wall is (a) 11.9 N·m (b) 46.7 N·m (c) 127 N·m (d) 104 N·m (e) 74.8 N·m
An open horizontal tank 2 m high, 2 m wide and 4m. long is full of water. a) How much water is spilled out when the tank is accelerated horizontally at 2.45 misec in a direction parallel with its longest side? b.) What is the porce acting on the side with the greatest depth? c.) Compute the required accelerating force.
A rectangular plane, 1.2 m by 1.8 m is submerged in water and makes qn angle of 30° with the horizontal, the 1.2 m sides being the horizontal. a. what is the minimum lressure acting on the plane in kPa b. what is the maximum lressure acting on the plane kPa c. Determine the magnitude of hydrostatic force acting on either side of the plane in KN. Support your computations with correctly drawn and labrled pressure prism diagrams.
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=75° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm2 and A=50 cm2 shall be taken for all rods.)
An open horizontal tank, 1.5m high, 2m wide, and 5m long is full oil (sp gr=0.9. it is accelerated in the direction parallel to the longer length at 2.3m/s^2 a) what is the force acting at the wall of the tank with the shortest depth in kN b) if the acceleration is increased by 0.88m/s^2, find the volume of oil spilled out
There is X=5m high water on the left side of a 3.5 m wide vertical cover sitting on the hinge shown in the figure. On the right, a water jet with a cross-sectional area of A=1100 cm2 hits the cover. a) Determine the horizontal hydrostatic pressure force acting on the cover and the vertical distance of the impact point to the hinge. b) What should be the Q flow rate of the water jet so that the lid remains vertical? (gravity forces will be neglected)
Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.12.9517 b.39.5136 c.30.4889 d.99.9358 What gage pressure p1 in kPa, is needed to provide the given flow rate? a.1692 kPa b.1121 kPa c.1328 kPa d.1725 kPa
The rectangular gate has dimensions: h=.8m; b=2.4m;c=0.4m;weighs 2 tons. It slides on a plane of inclination θ=70° and serves to plug the conduit of a dam. Considering that the coefficient of friction is 0.35. Determine the magnitude of the tension T needed to move the gate when the water level reaches the elevation of 62 m.
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=30° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm² and A=50 cm² will be taken for all bars.)