Answered: The square plate is confined within the…

Name: Vc=4.05 m/s. Determine the direction angle of the velocity of
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Vc=4.05 m/s. Determine the direction angle of the velocity of point C at this instant measured counterclockwise from the postive x axis. (Express answer in degrees to three significant figures) The square plate is confined within the slots at

Engineering

Mechanical Engineering

The square plate is confined within the slots at A and B as shown in (Figure 1). When 0= 40°, point A is moving at VA = 4 m/s. Figure B 0.3 m D 0.3 m K C 1 of 1 >

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.16P: Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020...

See similar textbooks

Similar questions

For the tutorial question, assume the inputs are: A = 0.75 [m] ; B = 1.03 [m] ; C = 0.685 [m] ; U = 33.5 [km/hr]; ANSWER: 1A) In the gradient equation of the keel L(z) = A + B · z; A = 1B) and B = 2) If Re_CR = ρ · U · L_CR; then L_cr [m] = 3A) To determine D_S, one needs first to calculate C_f_l(z). In the equation C_f_l(z) = D / l(z)^(-0.2) + E / l(z); D = 3B) and E =
Q 1(a) Use the below given data and calculate the metacentric height. Note: Explain each and every step. w= 200g W=2533.2g Displacement x (mm) 80 60 40 20 0 20 40 60 80 Tilt angle Ɵ (degree) 9.5 7.5 5.5 3 3 5.5 7.5 9.5 M.H (b) By using U-tube manometer how can you find out the pressure head? (c) If you are lacking of equipment, how can you determine the discharge of any channel?
Answer is: V = 14.17 ft/s
Answer: 57.4 ft/s=17.5m/sTorricelli's equation does not apply but the simplified Bernoulli's equation does apply.
Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020 (channel with a nominal depth of 10 in., weighing 201b/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following properties for the cross section: A=5.88in.2,Ix=78.9in.4, and Iy=2.81in.4. If two of these channels are welded together as shown in Fig. (b), find Ix and Iy for the resulting cross section.
Plz, solve both parts and show what have been asked in the problem parts. Problem. 7.13. A ship 180m long is to operate at a speed of 40km/h, what should be its speed in m/s to give the same froud number? What is the value of the froude number?
A turbine has the following data: inlet radius = 2.2 m outlet radius = 1.5 m blade width at inlet = 0.8 m blade width at outlet = 2.1 m inlet blade angle = 66º outlet blade angle =18.5ºN = 100 rpm Q = 85 m3/s Calculate the angle at the inlet by which the wicket gates should turn the flow from radial. Round off your final answer to two decimal places.
For more than a century, woodsmen harvested trees inSkowhegan, ME, elevation 171 ft, and fl oated the logsdown the Kennebec River to Bath, ME, elevation 62 ft, adistance of 72 miles. The river has an average depth of14 ft and an average width of 400 ft. Assuming uniformfl ow and a stony bottom, estimate the travel time requiredfor this trip.
Discuss the similarities and contrasting features in the derivations of the following equations: Piezometric head Euler's eq Bernoulli's eq Energy eq
When calculating the youth's modulus, don't we need to calculate from the slope? E = (0.285949012 - 0.067655044) / (0.01219802 - 0.001861386) Shouldn't it be this way? Or is it calculated based on a single point as you did?
engineering fluid mechanics A rectangular open channel has a base of length 2b, and the water is flowing with a depth of b. a. Sketch this channel.
A dam with triangular cross section holds back a body of water. The dam has height h. The dam is made of concrete, which has speci…c gravity 3.1. What is the maximum angle, , for which thedam will not tip over about point O?