7.14 In a 1:40 model of the flow over the crest of a spillway the velocity at a particular point is 0.5 m/s. What velocity does this represent in the prototype? The force exerted on a certain area in the model is 0.12 N. What would be the force on the corresponding area in the prototype? Develop your own dimensionless ratios.

7.14 In a 1:40 model of the flow over the crest of a spillway the velocity at a particular point is 0.5 m/s. What velocity does this represent in the prototype? The force exerted on a certain area in the model is 0.12 N. What would be the force on the corresponding area in the prototype? Develop your own dimensionless ratios.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Similar questions

A one-fiftieth-scale model of a military airplane is tested at1020 m/s in a wind tunnel at sea-level conditions. Themodel wing area is 180 cm 2 . The angle of attack is 3 ° . If themeasured model lift is 860 N, what is the prototype lift,using Mach number scaling, when it flies at 10,000 m standardaltitude under dynamically similar conditions? Note:Be careful with the area scaling.
A dam 75 ft wide, with a nominal flow rate of 260 ft 3 , is tobe studied with a scale model 3 ft wide, using Froude scaling.( a ) What is the expected flow rate for the model?( b ) What is the danger of only using Froude scaling for thistest? ( c ) Derive a formula for a force on the model as comparedto a force on the prototype.
The power P generated by a certain windmill design depends on its diameter D, the air density p, the wind velocity V, the rotation rate w and the number of blades n. a) Write this relationship in dimensionless form. A model windmill of diameter 50 cm develops 2.7 kW at sea level when V=40 m/s and when rotating at 4800 r/min. b) What power will be developed by a geometrically and dynamically similar prototype, of diameter 5 m, in winds of 12 m/s at 2000 m standard altitude? c)What is the appropriate rotation rate of the prototype?
A 1:7 scale model simulates the operation of alarge turbine that is to generate 200 kW with a flowrate of 1.5 m3/s.What flow rate should be used inthe model, and what power output is expected?(a) Water at the same temperature is used in bothmodel and prototype.(b) The model water is at 25°C and the prototypewater is at 10°C.
A dam 74 ft wide with a nominal flow rate of 260 ft3/s is to be studied with a scale model 3 ft wide using Froude scaling. What is the expected flow rate for the model? Derive the formula for a force on the model as compared to a corresponding force on the prototype.
The Stokes number, St, used in particle-dynamics studies is a dimensionless combination of 5 variables: acceleration of gravity g, viscosity μ, density p, particle velocity U, and particle diameter D. If St is propotional to μ and inversely proportional to g, find its dimensionless form.
A liquid of density ? and viscosity ? is pumped at volume flow rate V· through a pump of diameter D. The blades of the pump rotate at angular velocity ? . The pump supplies a pressure rise ΔP to the liquid. Using dimensional analysis, generate a dimensionless relationship for ΔP as a function of the other parameters in the problem. Identify any established nondimensional parameters that appear in your result. Hint: For consistency (and whenever possible), it is wise to choose a length, a density, and a velocity (or angular velocity) as repeating variables.
The thrust force of propeller (P) depends upon the flow velocity V, angular velocity o, diameter D, dynamic viscosity , density p. the speed of sound in the medium C. (1) Derive the relationship between the above variables and the thrust force by using Buckingham's IT-theorem. (2) Explain the physical meaning of the obtained dimensionless groups. إجابت
A simply supported beam of diameter D , length L , and modulusof elasticity E is subjected to a fluid crossflow of velocityV , density ρ , and viscosity μ . Its center deflection δ isassumed to be a function of all these variables. ( a ) Rewritethis proposed function in dimensionless form. ( b ) Suppose itis known that δ is independent of μ , inversely proportionalto E , and dependent only on ρ V 2 , not ρ and V separately.Simplify the dimensionless function accordingly. Hint:Take L , ρ , and V as r e peating variables.
A tiny aerosol particle of density ?p and characteristic diameter Dp falls in air of density ? and viscosity ?. If the particle is small enough, the creeping flow approximation is valid, and the terminal settling speed of the particle V depends only on Dp, ? , gravitational constant g, and the density difference (?p − ? ). Use dimensional analysis to generate a relationship for V as a function of the independent variables. Name any established dimensionless parameters that appear in your analysis.
1:25 scale model of a submarine is tested at 180 ft/s in a wind tunnel using sea-level standard air. What is the prototype speed in seawater at 20°C for dynamic similarity? If the model drag is 1.6lb, what is the prototype drag?
The power P generated by a certain windmill design dependson its diameter D , the air density ρ , the wind velocity V , therotation rate Ω , and the number of blades n . ( a ) Write this relationship in dimensionless form. A model windmill, of diameter50 cm, develops 2.7 kW at sea level when V = 40 m/s andwhen rotating at 4800 r/min. ( b ) What power will be developedby a geometrically and dynamically similar prototype, ofdiameter 5 m, in winds of 12 m/s at 2000 m standard altitude?( c ) What is the appropriate rotation rate of the prototype?