The state of stress at a point in member is given by: 50 60 100 60 40 80 MPa 100 80 20 A torsion test performed on a specimen made of the same material shows that yielding occurs at a shearing stress of 140 MPa. Examine using maximum distortion energy theory if yielding will be occur under the state fo stress.

The state of stress at a point in member is given by: 50 60 100 60 40 80 MPa 100 80 20 A torsion test performed on a specimen made of the same material shows that yielding occurs at a shearing stress of 140 MPa. Examine using maximum distortion energy theory if yielding will be occur under the state fo stress.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A bracket is under a loading condition is shown below. It's made from a steel with the yield strength (Sy) of 420 MPa. Using either maximum shear stress theory or distortion energy theory, determine the maximum load P that can be applied before yielding happens.
The state of stress acting at a critical point on a wrench is shown. Determine the smallest yield stress for steel that might be selected for the part, based on the maximum distortion energy theory.
A steel with a yield stress of 300 MPa is tested under a state of stress whereσ2 = σ1/2 and σ3 = 0. What is the stress at which yielding occurs if it isassumed that:(a) The maximum-normal-stress criterion holds?(b) The maximum-shear-stress criterion holds?(c) The distortion-energy criterion holds?
A bar AISI 1035 steel forged and heat treated with minimum yield strength of 570MPa is subjected to bending moment of 290Nm and a torsional moment of 310Nm. Assuming a factor of safety of 2, determine the diameter of rod using the following theories of failure (i) Maximum Shear stress theory and (ii) Distortion Energy theory (iii) Maximum stress theory, also specify which diameter is considered as safe
Annealed low-carbon steel has a flow curve with strength coefficient = 80,000 lb/in2 and strain-hardening exponent = 0.25. A tensile test specimen with gage length = 2.0 in is stretched to a length = 3.5 in. Determine the flow stress and average flow stress that the metal experienced during this deformation. use correct stratgy and correct E 0.55962
The state of plane stress at a critical point in a steel machine bracket is shown. If the yield stress for steel is sY = 36 ksi, determine if yielding occurs using the maximum distortion energy theory.
A material is subjected to plane stress. Express the distortion energy theory of failure in terms of sx, sy, and txy.
An aluminum alloy is to be used for a solid drive shaft such that it transmits 30 hp at 1200 rev>min. Using a factor of safety of 2.5 with respect to yielding, determine the smallest-diameter shaft that can be selected based on the maximum shear stress theory. sY = 10 ksi.
The figure (attached) shows a belt pulley mechanism which is loaded statically. The shaft is made of AISI 1030 steel with the yield strength of 480 MPa. Using distortion energy theory (DET), determine the diameter of the shaft with a factor of safety of 2.
If a shaft is made of a material for which sY = 75 ksi, determine the maximum torsional shear stress required to cause yielding using the maximum distortion energy theory.
Produced from xCy steel material by machining method, the shaft is bedded at C and D points. With the shaft, constant Fy= 820 N forces in the vertical direction and constant Fx= 4,2 kN forces in the axial direction, which do not rotate together. The tensile strength of the shaft material is (sigma)tensile = (sigma)ut = 620 MPa and the yield strength is (sigma)yield = 420 MPa. For 50% reliability, analyze the fatigue damage condition of the shaft sections A and B separately.
1. A part made of Aluminum 6061-T6 has a yield strength = 400 MPa. For each stress state below, draw all 3 Mohr's circles, find the principal stresses, and calculate the safety factor against yield using both the distortion-energy (von Mises) and maximum shear stress (Tresca) criterions. (If relevant) A clearly labeled diagram (or diagrams) clearly pertaining to your analysis with a coordinate system and relevant labels. Final answer with appropriate units and significant figures. You can use the fprintf() command in MATLAB to format numerical results A 2-3 sentence reflection on your answer. Does it make sense? Why or why not? What are some implications?