SEATWORKThe steel strut transmits a compressiveforce P=75 kN as shown in the figure. Thestrut has a hallow cross section with athickness of 12 mm, and the angle 0between the strut and the horizontal andthe horizontal plane is 45°. An 18-mmdiameter pin through the strut transmitsthe compressive force to two gusset platesPinthat are welded to the base. Four 20-mmdiameter bolts anchor the plate toconcrete. The thickness of the gusset is 16mm. The thickness of the base plate is 16Gusset,StrutBase plateBoltsmm.Calculate the following.a. The bearing stress between the pin and the gusset.b. The shearing stress in the bolts.The bearing stress between the anchor bolts and the base plate.с.Strut

Answered: Image /qna-images/answer/c903155a-e1ab-4797-97f4-79f2777af303.jpg

The steel strut transmits a compressive force P=75 kN as shown in the figure. The strut has a hallow cross section with a thickness of 12 mm, and the angle 0 between the strut and the horizontal and the horizontal plane is 45°. An 18-mm diameter pin through the strut transmits the compressive force to two gusset plates that are welded to the base. Four 20-mm Pin diameter bolts anchor the plate to concrete. The thickness of the gusset is 16 mm. The thickness of the base plate is 16 Gusset, Strut Base plate Bolts mm. Calculate the following. a. The bearing stress between the pin and the gusset. b. The shearing stress in the bolts. The bearing stress between the anchor bolts and the base plate. с. Strut

The steel strut transmits a compressive force P=75 kN as shown in the figure. The strut has a hallow cross section with a thickness of 12 mm, and the angle 0 between the strut and the horizontal and the horizontal plane is 45°. An 18-mm diameter pin through the strut transmits the compressive force to two gusset plates that are welded to the base. Four 20-mm Pin diameter bolts anchor the plate to concrete. The thickness of the gusset is 16 mm. The thickness of the base plate is 16 Gusset, Strut Base plate Bolts mm. Calculate the following. a. The bearing stress between the pin and the gusset. b. The shearing stress in the bolts. The bearing stress between the anchor bolts and the base plate. с. Strut

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.14P: A crane boom of mass 450 leg with its center of mass at C is stabilized by two cables AQ and BQ (Ae=...

See similar textbooks

Similar questions

A crane boom of mass 450 leg with its center of mass at C is stabilized by two cables AQ and BQ (Ae= 304 mm2 for each cable) as shown in the figure. A load P = 20 KN is supported at point D. The crane boom lies in the y-z plane. (a) Find the tension forces in each cable: TAQand TBQ(kN}. Neglect the mass of the cables, but include the mass of the boom in addition to load P. (b) Find the average stress (s) in each cable.
A horizontal bracket ABC consists of two perpendicular arms AB of a length 0.75 m and BC of a length 0,5 m. The bracket has a solid, circular cross section with a diameter equal to 65 mm. The bracket is inserted in a friction less sleeve at A (which is slightly larger in diameter), so it is free to rotate about the r0 axis at A and is supported by a pin at C Moments are applied at point C M{=1.5 kN -m in the x direction and A/3 = L0 kN-m acts in the — z direction. Considering only the moments Mxand M2, calculate the maximum tensile stress t, the maximum compressive stress crc* and the maximum in-plane shear stress Tmax at point />, which is located at support A on the side of the bracket at mid-height
By what distance h does the cage shown in thefigure move downward when the weight W is placedinside it? (See the figure.)Consider only the effects of the stretching of thecable, which has axial rigidity EA =10,700 kN. Thepulley at A has a diameter dA = 300 mm and the pulleyat B has a diameter dB = 150 mm. Also, the distanceL1 = 4.6 m, the distance L2 = 10.5 m, and the weightW = 22 kN. Note: When calculating the length of the cable, include the parts of the cable that go around thepulleys at A and B.
Two gondolas on a ski lift are locked in the postion show in the figure while repairs are being made elsewhere.The distance between support towers is L = LOO ft.The length of each cable segement under gondolas weighing WB= 450 lb and Wc=650 lb are DAB=12 ft, DBC=70 a , and DCB=20 ft . The cable sag at B is AB = 3.9 ft and that C is A = 7.1 ft.THe effective cross-sectional area of the cables is Ae=0.12 in". (a) Find the tension force in each segment; neglect the mass of the cable. (b) Find the average stress(σ) in each cable segment.
As shown in the figure, a homogeneous 100-kgrigid block is suspended by the three springs whoselower ends were originally at the same level. Eachsteel spring has 24 turns of 10-mm-diameter on amean diameter of 100 mm, and G = 83 GPa. Thebronze spring has 48 turns of 20-mm-diameterwire on a mean diameter of 150 mm, and G = 42GPa. Compute the maximum shearing stress ineach spring using A.M. Wahl formula.
Find the support reacions and joint force of the construction shown on the figure, if; P=12 kN q=9 kN/m M=12 kN and L=2 m
The BC and DE bars in the figure are made of steel (Eç = 200GPA), each of which has a width of 12 mm and a thickness of 6 mm. According to this; a-) When a force of P = 2.4 kN is applied to the rigid element AF, the tails formed in BC and DE bars,
What is the maximum possible value of theclamping force C in the jaws of the pliers shown inthe figure if the ultimate shear stress in the 5-mmdiameter pin is 340 MPa?What is the maximum permissible value of theapplied load P to maintain a factor of safety of 3.0with respect to failure of the pin?
An aluminum pole for a street light weighs4600 N and supports an arm that weighs 660 N (seefigure). The center of gravity of the arm is 1.2 m from theaxis of the pole. A wind force of 300 N also acts in the (-y)direction at 9 m above the base. The outside diameter ofthe pole (at its base) is 225 mm, and its thickness is 18 mm. Determine the maximum tensile and compressivestresses σt and σc, respectively, in the pole (at its base)due to the weights and the wind force.
A steel plate of dimensions 2.5 x 1.5 x 0.08 m and weighing 23.1 kN is hoisted by steel cables with lengths L1 = 3.2 m and L2 = 3.9 m that are each attached to the plate by a clevis and pin (see figure). The pins through the clevises are 18 mm in diameter and are located 2.0 m apart. The orientation angles are measured to be s = 94.4' and a = 54.9° For these conditions, first determine the cable forces T1 and T2, then find the average shear stress Taver in both pin 1 and pin 2, and then the average bearing stress ?? between the steel plate and each pin. Ignore the weight of the cables.
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa Determine maximum load P for block shear
A Pin spanner as shown in Figure, requires moment of 80 Nm to turn the 200 mm diameter shaft about its center O under the action of the applied force P. determine the contact reaction force on the smooth surface at the point A. Engagement of the pin at B may be considered to occur at the periphery of the collar OPTIONS:(MULTI CORRECT(MAY BE)): 1.Reaction at Point A is around 1047 N 2.Value of force P is around 102 N 3.Value of force P is around 133 N 4.Reaction at Point A is around 720 N 5.Reaction at Point A is around 1321 N 6.Value of force P is around 200 N 7.Value of force P is around 213 N 8.Reaction at Point A is around 970 N