The stresses shown act at a point on the free surface of a stressed body. Normal and shear stress magnitudes acting on horizontal andvertical planes at the point are Sx = 97 MPa, Sy = 37 MPa, and Sy = 71 MPa. Assume ß = 58°.Determine the normal stresses o, and ơ,and the shear stress Tng at this point if they act on the rotated stress element shown.SsyTntơnAnswers:MPaiO, =MPaiMPaTn =

Please refer the attached image for complete solution. THANK YOU.

The stresses shown act at a point on the free surface of a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sy = 97 MPa, Sy = 37 MPa, and Sy = 71 MPa. Assume ß = 58°. Determine the normal stresses a, and o and the shear stress T at this point if they act on the rotated stress element shown. Sxy Tnt Answers: i MPa MPa O, = MPa i Tn =

The stresses shown act at a point on the free surface of a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sy = 97 MPa, Sy = 37 MPa, and Sy = 71 MPa. Assume ß = 58°. Determine the normal stresses a, and o and the shear stress T at this point if they act on the rotated stress element shown. Sxy Tnt Answers: i MPa MPa O, = MPa i Tn =

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.1CTP: EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on...

See similar textbooks

Similar questions

EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, =- 200 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B= 48°
The vertical stress at point P1 due to the point load Q on the ground surface as shown in figure is sigma_{z} According to Boussinesq's equation, the vertical stress at point P2 shown in figure will be
Q#2 Draw the Mohr,s circle for the stress element shown in figure. Determine the principal stresses and maximum in-plane shear stresses and also draw respective stress elements. Furthermore find out stresses on planes whose normal make an angle of 45 and 135 degress with x-axis. Show your results on stress elements (10 marks)
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 17 ksi, Sy = 11 ksi, and Sxy = 17 ksi. (a) Draw Mohr’s circle for this state of stress. (b) Determine the principal stresses (σp1>σp2) and the maximum in-plane shear stress τmax acting at the point. (c) Find the smallest rotation angle θp (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)
Determine the stress components (σx′ , τx′y′) acting on the inclined plane AB in (Figure 1), where τxy=−38.5MPa. Solve the problem using the method of equilibrium.
state of plane stress at a point is represented by the stress element below: A. Draw the Mohr’s Circle. B. Determine the principle stresses and draw the corresponding stress elements. C. Determine the maximum shear stress and draw the corresponding stress element. D. Find the stresses on an element inclined at 50o clockwise and draw the corresponding stress element. E. Provide a table illustrating the stress values as well as the inclination angles and compare the obtained values from Mohr’s Circle with those obtained fro
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 17 ksi, Sy = 24 ksi, and Sxy = 16 ksi. (a) Determine the principal stresses (0p1 > 0p2) and the maximum in-plane shear stress max acting at the point. (b) Find the smallest rotation angle Op (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)
Determine the magnitude of the shear stress (in units of MPa) when the state of stress is oriented 45 degrees from the element shown (aligned with line AB).
Determine the maximum of the following: Bearing Stress, Tensile stress, and Shear stress in MPa if P=115 kN Note: the figure given is provided for the three stress that is needed to solve
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 19 ksi, Sy = 25 ksi, and Sxy = 19 ksi. (a) Determine the principal stresses (σp1>σp2) and the maximum in-plane shear stress τmax acting at the point. (b) Find the smallest rotation angle θp (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)
The supported beam in the figure has its cross section and area shown. Determine the Absolute Maximum Bending Stress, draw the stress distribution over the cross section at this location. Also, what is the stress at point C of the cross section?