The structure is pin supported at C and roller supported at A and a 300 N load is applied as shown in the figure. Determine the internal normal force, internal shear force and internal bending moment at point B. α = 30° 4 m 2 m 300 N 3 m. 3 m

The structure is pin supported at C and roller supported at A and a 300 N load is applied as shown in the figure. Determine the internal normal force, internal shear force and internal bending moment at point B. α = 30° 4 m 2 m 300 N 3 m. 3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Question 2: True or False? Please give simple reason for each of them. (1) Diffusion is a time and…

A: (1) True. Diffusion is a time and temperature-dependent phenomenon by atomic transport. Diffusion…

Q: C Situation 7 - A rectangular bar 50 mm x 75 mm in cross-section is subjected to a tensile force P =…

Q: A city supply of 15000 cubic metres of water per day is treated with a chlorine dosage of 0.5 ppm.…

Q: Q1/ Using the method of components, calculate the magnitude, direction, and location of the total…

A: ∠RPO=θtanθ=4015⇒θ=69.44° y15=16.6740⇒y=6.25'

Q: Q1: For the following data, calculate the "Stopping Sight Distance" and the "Passing Sight…

Q: Analyze the continuous beam shown below by the moment distribution method. Determine the value of…

A: Continuous beam is given as To find:- Analysis of the beam by moment distribution method Moment at…

Q: 6 Which of the following gives the reaction at C in the given beam? 300N 210 N/m A 100 Nm TITT 5m B…

Q: ( Determine the slope and deflection at point B of the steel beam shown below using conjugate beam…

Q: *4-24. The beam is subjected to the uniformly distributed moment m (moment/length). Draw the shear…

A: Given : Required : Shear and moment diagram

Q: A 2-span beam is loaded as shown. Assumed El is constant, use SDM. Show all equations including the…

A: Determine the absolute moment at C and B using Slope-Deflection Method.

Q: Draw the shear and moment diagram of this beam. -8- 30 -4 -4 4 kN/m -8 m B 80 kN-m +4m- 2 -200 30 kN…

A: Given: Required : Shear and moment diagram

Q: day and t What is population equivalent of a city, if the average sewage from the city is 106 1/…

A: A city having, Average sewage = 106 l/day, Average 5 day BOD=300 mg/L, BOD of domestic sewage = 80…

Q: eight at 0kpa: 396 g Weight at -33kpa: 325 g Weight at -1500kpa: 291 g Weight at -3100kpa: 280g…

A: Weight at 0kpa: 396 gWeight at -33kpa: 325 gWeight at -1500kpa: 291 gWeight at -3100kpa: 280gWeight…

Q: Situation 7-Precast concrete pile, 400 mm x 400 mm x 20 m long is to be lifted from 19. If the pile…

A: A Precast concrete pile, 400 mm x 400 mm x 20 m long is to be lifted from the casting bed. 19. If…

Q: Sample of clay isotropically normally compressed to an all round effective pressure of 100 kPa and…

A: Given; Effective pressure = 100 kpa Effective isotropic pressure = 50 kpa Initially back pressure =…

Q: 4-57. Determine the moment of this force F about an axis extending between A and C. Express the…

A: Force vector (F)=Coordinates:

Q: (Q2) Calculate coordinates of point P (by Tienstra formula) in the following drawing if you know: A…

A: Given; Point Easting Northing A 23808.69 19480.97 B 23930.75 19769.49 C 23989.38 19602.00…

Q: Q5: A) Define D-index and find it for the below 10 hours duration rain storm hyetograph where the…

Q: The intensity of rain fall and the time interval of a typical storm are Time interval (minutes)…

A: Given data:

Q: Determine the spacing of vertical stirrups near the left support of the "L"(m) beam loaded as shown…

A: The width of beam = 320 mmThe effective depth of beam =520 mmf'c = 35 MPafyt = 415 MPaDead Loads…

Q: When the coefficient of rugosity is increased from 0.01 to 0.02, the gradient of a pipe of a given…

Q: A footing 3.0 x 3.0 m carries a net foundation pressure of 130 kPa at a depth of 1.2 m in a deep…

A: Size of footing=3m x 3m , Net Foundation Pressure , qn = 130kPa , Depth = 1.2m , Unit weight of sand…

Q: Problem Solving: Round off your final answer to 2 decimal places. 3m 3m 4 m 20 kN 15 kN 10 kN 2 D…

A: For the frame provided below, consider the following properties, Members along level 2: Regular…

Q: Q3/ Consider a point in a structural member that is subjected to plane stress. Normal and shear…

A: Determine a. Principal stress and maximum shear stress in plane. b. Show the stresses in…

Q: Prove that = (1-n) (1 + wc) GsYw

A: Given : A relation between Bulk Unit Weight; Water content; Specific gravity; Unit weight of…

Q: Q3:- A parabolic vertical curve joins a grade of -3% to a grade of +5.5 %. The PVI is at station…

A: The downward gradient (g1) = -3% = -0.03 The upward gradient (g2) = +5.5% = 0.055The station of…

Q: A single-lane racetrack is being constructed with a 150 mph design speed. A curve on this track has…

A: Given;Design speed = 150 mph = 220 ft/sec V=…

Q: A lake with a surface area of 275 ha has the values of: relative humidity = 60% wind velocity at…

A: Given;Surface Area = 275 ha.Relative humidity = 60% Wind velocity at 1m above the ground (u1) = 10…

Q: Weight at 0kpa: 396 g Weight at -33kpa: 325 g Weight at -1500kpa: 291 g Weight at -3100kpa: 280g…

A: Given Data - Soil core volume = 247 cm^3 Weight at 0 kpa : 396 gWeight at -33 kpa : 325 gWeight at…

Q: A WF16x67 is made from A572 grade 50 steel. A ¾ in. cover plate, 9in. wide, is welded to the top…

A: To find the plastic moment strength of the beam in ft-kips, we need to first determine the plastic…

Q: A triangular channel with apex angle 60° is carrying a uniform flow of 4.25 m³/s with a depth of…

Q: A septic tank of 7 m³ in volume serves for 5 accumulation of sludge is people. If the rate of 70…

A: Volume of the septic tank (V) = 7 m3,Number of people (n)= 5 Rate of accumulation of sludge = 70…

Q: What are the difference between Spatial Resolution and Color Resolution

A: Context: Spatial Resolution and Color Resolution

Q: Draw shear force diagram and bending moment diagram of the beam shown in figure 2 below. Then…

Q: Situation 2-A rigid bin holds three identical cylinders stacked as shown in the figure. Each…

Q: For a road with a distance = 3 km. Calculate (TMS) AND (SMS) for the following traffic. car Time…

A: Note: It is assumed that time in minutes why because it is impossible for the cars to cover a…

Q: The beam shown below has internal hinges at points B and D. Assume EI is constant. Using conjugate…

A: internal hinge at B and D.

Q: Calculate the actual velocity of a jet at vena contracta of an orifice, if the theoretical velocity…

A: Theoretical discharge of the pump = 20 m/sec. Coefficient of discharge = 0.98 The actual discharge…

Q: he following is a section of a precedence diagram with contiguous activities. Using the given lag…

A: Find the Calculation methods below: Early Start -- For the first activity, the Early start is 0,…

Q: Two Pegs A and B were fixed on opposite banks of a 50 m wide river. The level was set up at A and…

Q: Find the deflection equation of the beam of length 1, with distributed uniform load w(x) = w0…

A: Find the deflection equation of the beam

Q: An embedded beam is subjected to the loads shown. Determine the stress produced at points A, B ,C, D…

Q: Write shear and moment equations for the beams in the following problems. In each problem, let x be…

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

Q: Cantilever sheet-pile wall penetrating into saturated clay with sand backfill. a. The depth of…

A: Find: (a) Depth of penetration (b) Maximum moment on sheet pile

Q: Q34 If the surface tension of water is 0.06N/m, then the capillary rise in a tube of a diameter 1mm…

A: Surface tension of the water T=0.06 N/m,Diameter d=1 mm,Angle = 0oTo Find-The value of the capillary…

Q: Situation 5 - The steel strut transmits a compressive force P = 75 kN as shown in the figure. The…

Q: A rectangular concrete channel (n = 0.014) has a bottom width of 12.0 m, a water depth of 6.0 m and…

A: A rectangular concrete channel-Manning's constant n=0.014,Bottom width b =12 m,Water depth d =6…

Q: Situation 12- Wooden planks 300 mm wide by 100 mm thick are used to retain soil soil exerts a…

Q: how the step 2 come and also in step 1 how did u take the term (20-x)?? can you explain this?

A: In step 2, influence line diagram is drawn using Muller Breslaw principal which states that to…

Question

need help solving this problem on statics

The structure is pin supported at C and roller supported at A and a 300 N load is applied as shown in the
figure. Determine the internal normal force, internal shear force and internal bending moment at point
B.
α = 30°
A
4 m
2 m
300 N
+
B
-3 m
C
3 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given that

Step 2: Calculation

Step 3: Calculation

Solution

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Assume point D is just to the left of the 60-kN force. Take wmax= 55 kN/m. Assume the support reactions at A and B are vertical. Determine the magnitude of the resultant internal bending moment on the cross section at point D
A truss is loaded with nodal force at C as shown TOS-003. If the truss members have identical rectangular section of 5 cm x 8 cm, with E = 70 GPa, compute the vertical displacement at joint C .
Determine the design angle θ (0° ≤ θ ≤ 90°) forstrut AB so that the 400-lb horizontal force has a componentof 500 lb directed from A towards C. What is the componentof force acting along member AB? Take Φ = 40°.
Determine the forces and moments at point C and point D For the SN kn/m the given is 66 kn/m
The resultant of the three forces shown is the force R = 200 N acting along z-axis. Determine P1, P2, and P3.
Determine the internal force at member BC if X = 78.98 and Y= 70.45
Determine the magnitude and orientation θ of FB sothat the resultant force is directed along the positive y axisand has a magnitude of 1500 N.
Compute the vertical components of the hinge forces at C as they act upon member AC in kN P= 89 kN and x= 3.7 m. Write numerical value only and in 2 decimal places
Calculate the moment of force of 1.4 kN with respect to points P1 and P2.
A beam is loaded and supported as shown.(a) Use the double-integration method to determine the reactions at supports A and C. Reaction forces are positive upwards and couples are positive counter-clockwise unless otherwise stated.(b) Draw the shear-force and bending-moment diagrams for the beam.Assume w = 29 kN/m, L = 11.2 m and EI = 6.3 x 104 kN·m2 is constant for the beam.
Solve for the axial forces on members BC, BD, and CD. Use theta= 18 degrees.
The force R is the resultant of the forces P, P2, and P3 acting on the rectangular plate. Find P, and P, if R=40 kN and Pz = 20 kN.