Draw the shear and moment diagram of this beam.-8-30-4-41V-DIAGRAM4 kN/m-8 m-B80 kN.m2-4 m-30 kNC-4--120-200M-DIAGRAM

Given: Required : Shear and moment diagram

Answered: Draw the shear and moment diagram of…

Engineering

Civil Engineering

Draw the shear and moment diagram of this beam. -8- 30 -4 -4 4 kN/m -8 m B 80 kN-m +4m- 2 -200 30 kN C -4 -120

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A steel frame is shown in the given figure. A L B L O L/2 C 777 El Constant D If joint O of the…

Q: (1) Using the double integration method, derive the equation of the elastic curve of the cantilever…

Q: Secant piles are often used in beachfront scour protection walls and basement groundwater cut-off…

A: a) Among the supplementary cementitious materials listed, ground granulated blast furnace slag…

Q: What does DFD levelling in FMEA and process modelling entail?

A: DFD (Data Flow Diagram) levelling in FMEA (Failure Mode and Effects Analysis) and process modeling…

Q: In a B.G. railway track, the specified ruling gradient is 1 in 250. The horizontal curve of 3° on a…

Q: 6-3: Find sag he and the reactions at the supports if hg = 3'. 6-4: Find sag he and the reactions at…

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 2.45 La barra rígida ABC está suspendida de tres alambres del mismo material. El área de la sección…

A: Given question is " The rigid bar ABC is suspended from three wires of the same material. The…

Q: To accommodate the rise and fall of the tide, a walkway from a pier to a float is supported by two…

A: RA = 1470 N

Q: Part B is Correct . Need help with part C and D

A: The given beam is shown below The unit load is applied at left end of beam. The reactions, shear…

Q: Lane groups are used during signal design to allocate green time among traffic movements at an…

A: Based on the intersection layout provided, the lane groups for the north-bound approach should be…

Q: Annual rainfall at a given location can be described by a normal distribution with a mean of 127 cm…

Q: A rectangular weir 10 √10 m wide has a constant head of 1 m. If the coefficient of discharge is 0.6…

A: Cd = 0.6 L = 1010 m, H = 1 m and g = 9.80m/s2 The discharge through a rectangular notch weir is…

Q: If the internal radius of a hollow shaft is n times the external radius, then ratio of torques…

Q: Q2/A pre-cast concrete factory was purch an advance, and the rest of the amount will be paid in the…

A: Given: Value of each installment= 17000$ Time of installments = 5 years Interest rate = 8% To find:…

Q: The state of stress at a point is given by: o= 80 MPa, oy=100 MPa and tauxv =60 MPa. If the yield…

A: State of stresses-σx=80 MPaσy=100 MPaτxy=60 MPayield strength-fy=150 MPa

Q: A simply supported beam has a uniformly distributed load of 4N/m. The allowable shear force of…

A: The simply supported beam has uniformly distributed Laod of 4N/m The allowable shear force of…

Q: Prove that = (1-n) (1 + wc) GsYw

A: Given : A relation between Bulk Unit Weight; Water content; Specific gravity; Unit weight of…

Q: 16" Design a rectangular footing for an Square Corner Column and PLL= 180 kips. Make the length of…

A: Square column size- 16''PDL= 280 kipsPLL=180 kipsL=1.5Bfy=60 ksif'c=4000 psifa=4 ksfFooting base-…

Q: A square box beam is made of two 20X80-mm planks and two 20X120-mm planks nailed together as shown.…

A: A square box beam is made of 80 x120 mm s=50 mm allowable shearing force= 300N As the maximum…

Q: A flood control structure having an expected life of n years is designed by considering a flood of…

Q: The shaft shown in Figure 4 is made of red brass C83400 copper with an allowable shear stress of 20…

A: Allowable shear stress, τa = 20 MPa L = 0.75m or 750 mm

Q: structures method of sections algebra,geometry and trigo

A: Consider Moment equilibrium at point D Fy*18 = 13*6+9*x tan50 = x6 x = 6*tan50 x = 7.15' Now Fy*18 =…

Q: 5.116 A pump is to move water from a late to a large, pressurized tank at a rate of 1,000 gallons in…

Q: The portal frame carries vertical and horizontal forces as shown in the figure below. If Mp is equal…

Q: A cantilevered prismatic beam (ABC) has a concentrated moment applied at the mid span (B). The beam…

A: Deflection at C is given by δc = Deflection caused at C by M and Deflection resisted at C by cable…

Q: How is the selection of the site of the small project through degree index systems measurement

A: It is asked to find the selection of the site of the small project through degree index systems…

Q: 5. The 1800-N force F is applied to the end of the I-beam. Express Fas a vector using the unit…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: 7. Draw the influence lines for the shear reactions at the internal hinges at points B and F, the…

Q: In the connection shown in Figure 5, ASTM A572 Grade 50 steel is used for tension member (C10-20),…

A: C 10 x 25 ( A = 7.35 in2 , tw = 0.526 in ) A572 grade 50 steel (Fy = 50 ksi and Fu = 65 ksi) We know…

Q: arce summation diagram and indicate whether eac SK

Q: If the time required for 50% consolidation of a remoulded sample of clay with single drainage is t,…

Q: The plate is deformed into the dashed shape as shown. If in this deformed shape, the horizontal…

A: The plate is deformed into the dashed shape L = 340 mma = 7mmb = 4 mm It is asked to determine the…

Q: The sum of the moments about point A due to the forces and couples acting on the bar is zero. a)…

A: Sum of forces and couple about A = 0 Couple at A = 20 kNm Vertical force at A = 5 kN Horizontal…

Q: A freeway section is estimated to carry an annual average daily traffic (AADT) of 40,000 vehicles…

A: Annual average daily traffic, AADT = 40,000 veh / day Directional factor , D = 0.6 , DDHV = 2640 veh…

Q: ble 3 90 BM2 R STATION ΤΡΙ Table 4 BMI TP2 75 [B] at D 4.53 BS 5.21 Lille 1 AD DO 875 me.. IH [A]…

A: Back sight, fore sight, height of instrument and elevation of different stations is given in the…

Q: A ball moving on a smooth horizontal table hits a rough vertical wall, the coefficient of…

A: Give data Ball is moving on the smooth surface. Assume initial velocity of ball = u And Hits to…

Q: 1) Use the method of PINS to determine the true magnitude and direction of the forces in all the…

A: Weight, W = 500 lbs It is asked to determine the forces in the members using method of pins.

Q: If the internal radius of a hollow shaft is n times the external radius, then ratio of torques…

Q: The hydraulic head that wou quick condition in a sand str 2.3 m, specific gravity 2.67 c 0.67 is…

Q: What is the maximum absolute shear in the following beam? Use L = 22, a = 3, b = 3, P₁=2, P2=5, and…

Q: 1. Draw the shear and moment diagram for the frame shown. 4 m A 100 KN 1.5 m+1.5 m 12 kN/m 5 m- 1

Q: A 2 mx 2 m tank with vertical sides contains oil of density 900 kg/m³ to a depth of 0.8 m floating…

Q: the virtual work method to determine the rotation of joint D of the frame shown

A: Using the virtual work method/ Unit load method, determine the rotation of joint D. In the…

Q: The centroid of the hatched portion from the base shown in the given figure is d d Half circle

Q: How do you define D in each part of the solution? Please explain also how do you find the maximun…

A: Number of lanes = 4 Number of lanes in each direction, N=2 Direction distribution, D = 0.7 Peak…

Q: A 4 kN/m 15 m 20 m C

A: Bearing reaction of a beam = ? EI is constant throughout the beam

Q: Return Period 1. Year Maximum depth of precipitation of certain area is presented below. Based on…

A: Year Max. rainfall depth, mm 1995 155 1996 151 1997 189 1998 157 1999 136 2000 280…

Q: Rainfall Depth and Intensity 2. Given the rainfall incremental depth compute the following; to =…

A: Given: to = 8:00 AM

Q: Use AISC Equation E3-2 or E3-3 and determine the axial compressive strength oP for the following…

A: Consider the column as in the below diagram;

Q: 1.47 A cylinder contains 12.5 ft³ of air at 120 °F and 40 psia. The air is then compressed to 2.50…

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

Draw the shear and moment diagram of this beam.
-8-
30
-
4
-41
V-DIAGRAM
4 kN/m
-8 m-
B
80 kN.m
2
-4 m-
30 kN
C
-4-
-120
-200
M-DIAGRAM

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Support reactions

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the maximum moment at the span of DE Draw the shear and moment diagram of the span of DE Given: Shear and moment at the left of C.Vc= -4.5 kN Mc= -4.5 kN-m Shear and moment at the right of c.Vc= 37.5 kN Mc= -94.5 kN-m Shear at e.Ve= 30 kN Shear and moment at point cVc= 0 Mc= -90 kN-m Shear and moment at point a.Va= 42 kNMa= -78 kN-m
Determine the magnitude of the moment produced by force F={-3i+8j+6k}N about the diagonal axis AF of the rectangular block. MAF=?
Find the support reactions at A, B, C, and D. Assume E = 200GPa, and I = 1705 x10^6mm4
Determine thee maximum positive shear and moment in the beam given that F=18 kN, U= 6kN/m and L=9 m
Determine the magnitude of the moment of the forceF = {50i - 20j - 80k} N about the base line AB of the tripod.
Determine the magnitude of the moment of the forceF = {50i - 20j - 80k} N about the base line BC of the tripod.
From the continuous beam shown. 1. Which of the following gives the moment equation for the span AB? a. 8MA + 4MB + 192 = 0 b. 4MA + MB + 48 = 0 c. MA - 4MB + 192 = 0 d. 8MA + MB + 96 = 0 2. Which of the following gives the moment equation at the span AB and BC? a. MA - 4MB = -192 b. 4MA + MB = - 48 c. 4MA + 20MB = -462 d. 8MA + MB = -96 3. Which of the following gives the moment at B.? a. -20.33 kNm b. -36.45 kNm c. -71.78 kNm d. -69.88 kNm
Draw the shear and moment diagram thenidentify the maximum shear and maximum moment. 12KN 18KN 12 KN
Determine the shear value (kN) when x = 1.2m from the left side of the beam where: L = 5.9 m; Wo = 128 kN/m
A cable was used to dry the clothes from wet laundry by hanging as shown below. The clothes are placed such that it approximately loads the cable by a uniform q(x) = qo. If [= 10 m, ha = 5 m, and he = 4 m, compute the maximum force in the cable for its minimum distance to the ground by 3 m. B y hA hB a (deg) = 16.446 q0 (Kn/m) = 37.632
C0nsider the frame bel0w where f0rce A = 55 N acts 0n p0int Q, f0rce B = 34 N acts on p0int P, and force C = 42 N acts on p0int M. Replace the system of f0rces acting on the frame with two f0rces, one acting on p0int O and the other acting vertically at point P. Calculate the magnitude and direction of the vertical f0rce acting on p0int P, FP, and the force acting on p0int O, FO.
Answer is 1,726. No other answer thanks From the given beam in the figure, compute the maximum moment (kN-m, magnitude only) at C due to a uniform dead load of 14 kN/m, uniform live load of 14 kN/m and a concentrated load of 93 kN by influence lines. Use a = 4 m., and b = 11 m.