The switch has been in the left position for a long time and is moved to the right position at time t= 0. Determine the time t when vc= 0.0 Volts.20 Ωt=010 212 V8 V1 µFΟ Α 6.06 μSO B. 1.54 µSO C.5.11 µSO D.4.05 µSO E. 2.88 µS

Answered: Image /qna-images/answer/d6b34083-c382-4b1c-8961-b839d8915d51.jpg

Answered: The switch has been in the leit…

The switch has been in the leit position for a long time and moved to the right position at time i nine the time i when 20 2 10 Ω t= 0 8 V 1 µF 12 V O A. 6.06 µS O B. 1.54 µS

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the circuit of the figure below, the switch S has been open for a long time. It is then suddenly closed. Take = 10.0 V, R1 = 43.0 kΩ, R2 = 180 kΩ, and C = 14.0 µF. (a) Determine the time constant before the switch is closed. (b) Determine the time constant after the switch is closed. (c) Let the switch be closed at t = 0. Determine the current in the switch as a function of time. (Assume I is in A and t is in s. Do not enter units in your expression. Use the following as necessary: t.) I keep messing up part C. any help you can give and explain would be appreciated.
L= 270 mHC= 860 uF For circuit; a) Find the time constant for t> 0. b) Find the equation for İ0 (t) for time t> 0. c) Find the equation V0(t) for time t> 0.
The switch is closed at t<0 and the circuit was working continuously. At t=0 the switch is opened. Find the voltage value (Va) at Point a at time t= 1 mili sec.
At t=0 the switch is turned off. Find the voltage Vc(t) at t=20 micro seconds?
The switch in the circuit hasbeen in position a for a long time. At t=0, it moves instantaneously toposition b. For t≥0+, find 1. a) vo(t).
The switch, which is in (a) position for a long time, is brought to (b) position at time t = 0. Accordingly, what is the value of the "i" current in 1 ms at time t> = 0 +?
Source voltage from Channel 1 output of oscilloscope and VR(t) and VL(t) voltages from Channel 2 output are desired to be observed by applying TTL signal to a series RL circuit with inductance value RL=270 mH, series R resistance 2.6 K and inductance internal resistance Rin=430 Ω. . The settings for the oscilloscope are as follows. Channel 1 Volt/div adjustment 2V Channel 2 Volt/div adjustment 2V Time/div=0.1ms Since the time t=5τ is 4.4 square units, a) If VL(t) voltage is desired to be observed from Channel 2, draw the required circuit diagram with oscilloscope channel connections. b) Plot the VR(t) and VL(t) waveforms to scale according to the 4V TTL source condition, showing the 5τ and τ times. Compare the τ value you obtained with the τ value you will theoretically calculate. c) If the unit square number of the peak value on the vertical axis at the end of t=5τ of the VR(t) voltage seen in Channel 2 is 1.4, find the current passing through the series RL circuit. d) Explain…
V1 = 28V, V2 = 30V, R1 = 14Ω, R2 = 4Ω, R3 = 18Ω, L= 4H, C = 4F Q1) The switch in Fig. (1) has been in position a for a long time. At t = 0, it moves to position b. Calculate iL(t) for all time.
A coil of inductance 2 Henrys and a resistance of 10 ohms is connected with an emf, E=200sin20t volts, where t is the time in seconds. I=0 when t=0. Find I when t=0.05 second.
What is the time constant for the circuit shown below, in ms (mili-seconds)? Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement.
In which condition, a system becomes time invariant? Determine whether the system, y[n]=x[n+7]+x[n-7] is time invariant or not.
Heart pacemaker Figure 3.1.12 shows a heart pacemaker, which consists of a switch, a battery, a capacitor, and the heart as a resistor. When the switch S is at P, the capacitor charges; when S is at Q, the capacitor discharges, sending electrical stimuli to the heart. In Problem 47 of Exercises 2.3 we saw that during this time when electrical stimuli are being applied to the heart, the voltage E across the heart satisfies the linear ED a) Suppose that in the time interval of duration the switch S is in position P as shown in figure 3.1.12 and the capacitor is charging. When the switch is moved to the Q position at time the capacitor discharges, sending an impulse to the heart during the time interval of duration ≤ t <. So the initial interval of charge discharges 0 < t < t1 + t2 the voltage in the heart is actually modeled by the differential equation defined by sections. As S moves between P and Q, the load intervals and download durations t1 and t2 are repeated…