Answered: The switch in the given circuit has…

The switch in the given circuit has been closed for a long time, and it is opened at t=0, Find V. across the capacitor for tz 0. 10 K Nc 20mA 10K 60mF 10K 10K

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter29: Direct Current (dc) Circuits

Section: Chapter Questions

Problem 88PQ

See similar textbooks

Related questions

Q: 10.0 pF 3. In the circuit below each capacitor initially has a charge of magnitude 3.50 nC on its…

A: Given data : Capacitor's initial charge, q=3.50 nC=3.50×10-9 C Energy loss is 80%, ∴Ef=0.2Ei…

Q: PL (mW) For the circuit shown, the power dissipated in the load 60 Resistance RL, is given as a…

A: The value of ResistanceRs.given,diagram,

Q: Refer to the given circuit. C1 = 5 µF C3 = 8 µF C2 = 4 µF C4 = 6 µF C5 = 4 µF DURACELL VT = 12 V…

Q: In the circuit shown. C switch S is closed and at the instant that the current in the circuit drops…

Q: The 6µF capacitor is initially uncharged. The switch Z is closed at time t =0. Approximate the…

A: Given: The supply voltage is 10 V. The resistance in the circuit is 6 Ohm and 3 Ohm. The capacitance…

Q: A series RL circuit with R = 10 Q and L = 5 H has a constant voltage E = 20 V applied at t = 0 by…

A: A series RL circuit with R = 10 ohm and L = 5 H has a constant voltage E = 20 V applied at t = 0 by…

Q: The switch in the following circuit has been opened for a long time. It is closed at t = 0.…

Q: Consider the circuit shown. Before the switch is closed, both capacitors are uncharged. V = 12.0 V,…

A: V = 12 volts R1 = 90 Ω R2 = 30 Ω R3 = 60 Ω C1 = 5 × 10-⁶ F C2 = 3×10-⁶ F

Q: An uncharged 5.0-µF capacitor and a resistor are connected in series to a 12-V battery and an open…

Q: When the switch is closed, the equivalent capacitance between points A and B is 4.0 nF What is the…

Q: C, = 5 µF C3 = 8 µF C2 = 4 µF C4 = 6 µF Cs = 4 µF DURACELL VT = 12 V

Q: An initially uncharged capacitor is connected as shown. If the switch is closed at t-0, the time it…

Q: A charged capacitor of C-62.0 µF is connected to a resistor of R-2.8 M2 as shown in the figure. The…

Q: The switch is closed in the figure. After a long time compared to the time constant of the…

Q: If the switch is closed for a long time and then opened at t=0. What is the initi Feras AI value of…

Q: For the parallel circuit given, compute for the dissipated power for R3 A 24.6 Watts B. 38.6 Watts…

A: Given data: Three resistors are connected in parallel combination R1 = 22 Ω R2 = 10 Ω R3 = 5 Ω…

Q: Consider a series RC circuit as in Figure below for which R =4.5 MQ, C=6.9 µF, and ɛ=30.0 V. Find…

Q: For the given circuit, the maximum power transferred to the load resistance (in mw) is: A R = 2002…

Q: Solve the series circuit below. Total 3 1 www 2{ V₁ = 24 V V₂ = 36 V V3 = V₁ = 1₁₂ = 1₂ = 13 = IT =…

Q: Consider a series RC circuit as in Figure below for which R =4.1 MQ, C=5.2 µF, and ɛ=30.0 V. Find…

Q: For the circuit in the figure, at t = 0 the switch S is closed with the capacitor uncharged. If C =…

Q: Find the charge q(t) on the capacitor and the current i(t) in the given LRC-series circuit. L = 1 h,…

Q: At t = 0 the switch S is closed with the capacitor uncharged. If C = 30 mF, ɛ = 30 V, and R = 7.9…

A: At t= 0 second, Capacitor charge = 0 Capacitor = 30 mF EMF, e=30 V Resistance= 7900 ohms

Q: Consider a series RC circuit as in Figure below for which R =6.1 MO, C=5.7 µF, and e=30.0 V. Find…

A: Given data: Resistance (R) = 6.1 MΩ = 6.1×106 Ω Capacitance (C) = 5.7 μF = 5.7×10-6 F Potential (ε)…

Q: Consider the circuit shown where the switch has been in position A for a long time. At time t = 0,…

Q: An uncharged 5.0-µF capacitor and a resistor are connected in series to a 12-V battery and a open…

Q: The switch S of the circuit shown below is closed at t = 0 . Determine (a) the initial current…

A: The expression for the current in RL circuits as a function of time can be given as, Here τ is the…

Q: The figure shows an LR circuit with L= 0.15 H, R = 25 2, and Vo = 36 V. The switch is initially…

Q: Refer to the given circuit. C1 = 5 µF C3 = 8 µF C2 = 4 µF C4 = 6 µF Cs = 4 µF DURACELL VT = 12 V…

Q: For the circuit shown in the figure, V = 20 V, C = 10 µF, R= 0.80 MQ, and the battery is ideal.…

A: At time t=0 s , the initial potential difference across the resistor is V0=20 V . The potential…

Q: For numbers 11 to 12, consider the circuit below. In this circuit Vpc = 6 V, R, = 100 N, R, = 200 Q…

A: Given that, R1= 100 ohm R2= 200 ohm R3= 300 ohm Voltage (Vdc)= 6 V

Q: A series RL circuit with R = 31 Q and L= 4 H has a constant voltage E applied at t = 0 by the…

Q: The capacitor in the circuit is initially uncharged. The switch closes at time t 0.

A: Given, R=4.7 k ohm time constant τ=RC Here τ=0.002

Q: Refer to the given circuit. C1 = 5 µF C3 = 8 µF C2 = 4 µF C4 = 6 µF Cs = 4 µF DURACELL VT = 12 V How…

Q: 10 μ 2.5 0.30 μF HE

A: Given:- C1= 10 μCC2=2.5 μC C3=0.30 μCVT= 10 V Find:- How much charge is on C3What is the voltage…

Q: Set up two (of 3 possible) loop equations and one junction equation. Then, find the currents through…

A: Given Let A,B,C,D,E,F are the name of each junction point . And I1,I2 are the current flowing in…

Q: In the shown circuit, the capacitor is initially uncharged. The switch S is closed at time t-0. Find…

A: Given: V=10 VC=2.0 μFR=0.05×106 Ω The initial current in the circuit is I0=VR

Q: Consider a series RC circuit as in Figure below for which R =3.1 MQ, C=3.3 µF, and ɛ=30.0 V. Find…

A: We have to Consider a series RC circuit as given in the Figure, and we have to find the current (in…

Q: The capacitor is initially uncharged when the switch is closed at t=0. When t equals 10s what does…

Q: QUESTION 11 Just after closing the switch S in the shown circuit, what is the current in the 15.0 Q…

Q: Fill in the table with the missing values (assume the switch has been closed): 120 R V |(2) | (V) |…

A: Given: Emf of the battery is 12 V. The values of resistors are 2 Ω, 4 Ω, 12 Ω. introduction: Ohm's…

Q: Consider a series RC circuit as in Figure below for which R =2.7 MQ, C=2.7 µF, and ɛ=30.0 V. Find…

Q: In the circuit shown in the figure, the S switch is closed at t = 0 and the capacitors, which are…

A: (A) τ = Req X Ceq (eq stands for equivalent) Req = R/2 = 25/2 = 12.5 ohm Ceq = C/2 = 9/2 = 4.5…

Q: Consider the circuit shown, where C=6.0 µF, C2=12 µF, and AV= 20 V. Capacitor G is first charged by…

Q: C2 Vap C3 C4 C5 The capacitors inche above circuit are initially uncharged. Apotential difference of…

Q: The current in a single-loop circuit with one resistance Ris 3.75 A. When an additional resistance…

Q: In a standard RLC circuit that we are looking at R = 0.075 Ω , L = 1.2 H and C = 1.6 F. The…

Q: If the switch is closed for a long time and then opened at t=0. What is the initial value of the…

Q: In the shown circuit, the capacitor is initially uncharged. The switch S is closed at time t-0. Find…

Q: At t = 0 the switch S is closed with the capacitor uncharged. If C = 30 mF, ɛ = 30 V, and R = 4.8…

Question

The switch in the given circuit has been closed for a long time, and it is
opened at t=0, Find V. across the capacitor for t2 0.
10 К
Nc
20mA
10K
10K
60mF 10K
+1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A capacitor with initial charge Q0 is connected across a resistor R at time t = 0. The separation between the plates of the capacitor changes as d = d0/(1 + t) for 0 t 1 s. Find an expression for the voltage drop across the capacitor as a function of time.
Figure P29.84 shows a circuit that consists of two identical emf devices. If R1 = R2 = R and the switch is closed, find an expression (in terms of R and ) for the current I that is in the branch from point a to b.
In the circuit of Figure P21.57, the switch S has been open for a long time. It is then suddenly closed. Take = 10.0 V, R1 = 50.0 k, R2 = 100 k, and C = 10.0 F. Determine the time constant (a) before the switch is closed and (b) after the switch is closed. (c) Let the switch be closed at t = 0. Determine the current in the switch as a function of time.
Figure P29.60 shows a simple RC circuit with a 2.50-F capacitor, a 3.50-M resistor, a 9.00-V emf, and a switch. What are a. the charge on the capacitor, b. the current in the resistor, c. the rate at which the capacitor is storing energy, and d. the rate at which the battery is delivering energy exactly 7.50 s alter the switch is closed?
In the RC circuit shown in Figure P29.78, an ideal battery with emf and internal resistance r is connected to capacitor C. The switch S is initially open and the capacitor is uncharged. At t = 0, the switch is closed. a. Determine the charge q on the capacitor at time t. b. Find the current in the branch be at time t. What is the current as t goes to infinity?
In Figure 33.9A (page 1052), the switch is closed at a at t = 0. Find an expression for the power dissipated by the resistor as a function of time, and sketch your result. Is the power lost greater as soon as the switch is closed or a long time after it has been closed? Does your answer make sense?
When the switch is open in Figure 18.8, power Po is delivered to the resistor R1. When the switch is closed, which of the following is true about the power Pc delivered to R1? (Neglect the internal resistance of the battery.) (a) Pc Po (b) Pc = Po (c) Pc Po Figure 18.8 (Quick Quizzes 18.5 and 18.6)
When the switch is open in Figure 18.8, power Po is delivered to the resistor R1. When the switch is closed, which of the following is true about the power Pc delivered to R1? (Neglect the internal resistance of the battery.) (a) Pc Po (b) Pc = Po (c) Pc Po Figure 18.8 (Quick Quizzes 18.5 and 18.6)
The circuit shown in Figure P28.78 is set up in the laboratory to measure an unknown capacitance C in series with a resistance R = 10.0 M powered by a battery whose emf is 6.19 V. The data given in the table are the measured voltages across the capacitor as a function of lime, where t = 0 represents the instant at which the switch is thrown to position b. (a) Construct a graph of In (/v) versus I and perform a linear least-squares fit to the data, (b) From the slope of your graph, obtain a value for the time constant of the circuit and a value for the capacitance. v(V) t(s) In (/v) 6.19 0 5.56 4.87 4.93 11.1 4.34 19.4 3.72 30.8 3.09 46.6 2.47 67.3 1.83 102.2
The switch is closed in Figure 18.20. After a long time compared with the time constant, of the circuit, what will the current be in the 2- resistor? (a) 4 A (b) 3 A (c) 2 A (d) 1 A (c) More information is needed. Figure 18.20 (Quick Quiz 18.9)
In an oscillating RLC circuit, R = 7.0 L. = 10 mH. And C = 3.0 F. Initially, the capacitor has a charge of 8.0 C and the current is zero. Calculate the charge on the capacitor (a) five cycles later and (b) 50 cycles later.
In the circuit of Figure P27.25, the switch S has been open for a long time. It is then suddenly closed. Take = 10.0 V, R1 = 50.0 k, R2 = 100 k, and C = 10.0 F. Determine the time constant (a) before the switch is closed and (b) after the switch is closed. (c) Let the switch be closed at t = 0. Determine the current in the switch as a function of time. Figure P27.25 Problems 25 and 26.