The system consists of 50-lb and 15-lb blocks A and B,respectively, and 5-lb pulleys C and D that can betreated as thin disks. Assume that the cord does not slipon the pulleys, and neglect the mass of the cord.(Figure 1)FigureC0.5 ft1AD0.5 ftB< 1 of 1Part ADetermine the speed of block A after block B has risen 5 ft, starting from rest.Express your answer to three significant figures and include the appropriate units.VASubmitμAValueProvide FeedbackRequest AnswerĆUnits?Next >

To solve this question first we will calculate the initial and final kinetic and potential energy…

The system consists of 50-lb and 15-lb blocks A and B, respectively, and 5-lb pulleys C and D that can be treated as thin disks. Assume that the cord does not slip on the pulleys, and neglect the mass of the cord. (Figure 1) Part A Determine the speed of block A after block B has risen 5 ft, starting from rest. Express your answer to three significant figures and include the appropriate units. μÀ Valua Inits ?

The system consists of 50-lb and 15-lb blocks A and B, respectively, and 5-lb pulleys C and D that can be treated as thin disks. Assume that the cord does not slip on the pulleys, and neglect the mass of the cord. (Figure 1) Part A Determine the speed of block A after block B has risen 5 ft, starting from rest. Express your answer to three significant figures and include the appropriate units. μÀ Valua Inits ?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.79P: The coefficient of rolling resistance between the 30-kg lawn roller and the ground is r=0.1. (a)...

See similar textbooks

Similar questions

Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.
The contact surface between the 36-lb block and 20-lb homogenous cylinder is frictionless. Can the system be in static equilibrium 0n the rough inclined plane?
Situation 02. A crate has a mass of 120kg and the coefficient of static and kinetic frictionis 0.60 and 0.50, respectively. The crate starts from rest and the motor exerts a tensionT= 1220 + 200t (N). If the elevation of the dock is 30 degrees from the horizontal,a. What is the velocity of the crate after 1sec?b. Compute the power transmitted after 1sec.
The 54-lb block rests on the rough surface for which the coefficient of kinetic friction is μk = 0.2. A force F=(40+s2)lb, where s is in ft, acts on the block in the direction shown. The spring is originally unstretched (s= 0) and the block is at rest. (Figure 1) Figure 1 of 1A picture shows a block laying on a horizontal surface with a spring of stiffness k equal to 20 pounds per foot attached to its right side. The other end of the spring is pressed against the wall. Force F is pushing the block to the right and downwards, at an angle of 30 degrees below the horizontal. Determine the power developed by the force the instant the block has moved s = 1.5 ft.
Blocks A and B have masses mA, and mB , respectively. Neglecting friction between all surfaces, draw the FBD and KD for each mass.
In a governor of the Hartnell type the arms of the bell-crank leversare equal in length, and those carrying the operating masses arevertical when the governor is rotating at its mean speed of 775rev/min, with the masses moving in a circle of 175 mm diameter -The usual central controlling spring is replaced by two paralleltension springs direetly connecting the operating masses. Find(a) the magnitude of each operating mass if a force of 90 N isrequired at the sleeve to maintain it in the mean speed positionwhen the specd is increased from 775 to 800 rev/m in(b) the stiffness, or rate, of each spring if the ratio of sleevemovement to increase of speed is 1 mm to 10 revImin when inthe mean speed position.
In the system shown two blocks A and B are joined by anegligible ground cable passing through a fixed pulley that does notbroken. Block A has a mass of 45 kg and the coefficients ofstatic friction are 0.40 between rope and pulley and 0.30 betweenblocks and inclined planes. Determine: a) The maximum mass of block B that will cause theblock A slides down.b) The minimum mass of block B that will cause block A to slide up.c) Explain the condition of the system if the mass of block B were 80 kg.
13-2. Determine the acceleration of the 30-kg block shown in Figure P13–2 above.
The conveyor belt shown in (Figure 1) delivers each 12-kg crate to the ramp at A such that the crate's speed is vAvA = 2.5 m/s, directed down along the ramp. The coefficient of kinetic friction between each crate and the ramp is μk = 0.27. Determine the smallest incline θ of the ramp so that the crates will slide off and fall into the cart.
consider the mass and pulley system in the attached file. mass m1 = 29 kg and mass m2 = 12kg. the angle of the inclined plane is given and the coefficient of kinetic friction between mass m2 and the inclined plane is uk = 0.12. assume the pulleys are massless and frictionless if the system is released from rest, what is the speed of mass m2 after 2.5 s? v(2.5 s) = ?
The W1= 69.01-lb block shown rests on a smooth plane (coefficient of kinetic friction = 0) with an angle of θ=34∘ from horizontal. It is connected by a flexible inextensible cord that passes around weightless, frictionless pulleys to a support. The W2 =134.93-lb weight is attached as shown. After the system is released from rest, in what distance will the block on the plain attain a speed of 10.0 ft/s?
A block of mass M1 resting on a 20.7° slope is shown. The block has coefficients of friction μs = 0.745 and μk = 0.464 with the surface. It is connected via a massless string over a massless, frictionless pulley to a hanging block of mass M2 = 2.62 kg. (a) What is the minimum mass M1 that will remain stationary and not slip? (b) If this minimum mass is nudged ever so slightly, it will start being pulled up the incline. What magnitude of acceleration will the minimum mass have?