The system is at rest with the spring unstretched when theta = 0. the 5.3 kg uniform slender bar is then given a slight clockwise nudge. The value of b is 0.45 m. (a) if the bar comes to momentary rest when theta = 58, determine the spring constant k. (b) for the value k = 65 N/m, find the magnitude of the angular velocity of th ebar when theta = 38 degrees. The system is at rest with the spring unstretched when 0 = 0. The 5.3-kg uniform slender bar is then given a slight clockwise nudge. Thevalue of bis 0.45 m. (a) If the bar comes to momentary rest when 0 = 58°, determine the spring constant k. (b) For the value k = 65 N/m,find the magnitude of the angular velocity of the bar when 0 = 38°1.21b

We begin by calculating the change in the kinetic and the potential energy of the system. The change…

The system is at rest with the spring unstretched when = 0. The 5.3-kg uniform slender bar is then given a slight clockwise nudge. The value of b is 0.45 m. (a) If the bar comes to momentary rest when = 58°, determine the spring constant k. (b) For the value k = 65 N/m, find the magnitude of the angular velocity of the bar when = 38° 14 1.21b

The system is at rest with the spring unstretched when = 0. The 5.3-kg uniform slender bar is then given a slight clockwise nudge. The value of b is 0.45 m. (a) If the bar comes to momentary rest when = 58°, determine the spring constant k. (b) For the value k = 65 N/m, find the magnitude of the angular velocity of the bar when = 38° 14 1.21b

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the system of two blocks. There is no friction between block A and the tabletop. The mass of block B is 5.00 kg. The mass of block A is 4.00 kg. The pulley rotates about a frictionless axle, and the light rope doesn’t slip on the pulley surface. The pulley has a mass of 2.00 kg and with a 0.100 m radius. The system is released from rest. (a) What is the angular speed of the pulley when block B falls 1.50 m? (The moment of inertia of the pulley = (1/2)MR^2) (b) How long does it take when block B falls 1.5 m? (block A and block B move with constant acceleration)
The 7.5-lb disk A has a radius r A = 6 in. and is initially at rest. The 10-lb disk B has a radius r B = 8 in. and an angular velocity w0 of 900 rpm when it is brought into contact with disk A. Neglecting friction in the bearings, determine (a) the final angular velocity of each disk, (b) the total impulse of the friction force exerted on disk A.
In the equilibrium position, the 30 kg cylinder causes a static deflection of [60] mm in the coiled spring. If the cylinder is depressed an additional [45] mm and released from rest, calculate: The position , velocity and acceleration of the cylinder at t = 1.2 s.
A cable is wrapped around the spool’s center hub. The mass of the spool is m= 100 kg, the radius r1 = 0.4 m, r2 =0.6 m, and the radius of gyration is kG = 0.3 m. A horizontal force P = 10 N is applied to the cord. The spool is initially at rest and rolls without slipping. (1) The angular impulse of the spool about point A after 2 second, =________(N·m·s) (two decimal places)
The velocity of the 8-kg cylinder is 0.3 m∕s at a certain instant. The speed v after dropping an additional 1.5 m is 2.5 m/s. The mass of the grooved drum is 12 kg, its centroidal radius of gyration is k = 210 mm, and the radius of its groove is ri = 200 mm. The frictional moment at O is a constant 3 N∙m. Find the frictional force.
A Porter governor has equal arms each 250 mm long and pivoted on the axis of rotation. Each flyball has a mass of 10 kg and the mass of the central load on the sleeve is 50 kg. The radius of rotation of the flyball is 150 mm when the governor begins to lift and 200 mm when the governor is at maximum speed. Find the range of speed, when the friction at the sleeve is neglected. Select one: A. 35.4 rpm B. 25.4 rpm C. 15.4 rpm D. 45.4 rpm
The position of the small 0.68-kg blocks in the smooth radial slots in the disk which rotates about a vertical axis at O is used to activate a speed-control mechanism. If each block moves from r = 162 mm to r = 200 mm while the speed of the disk changes slowly from 272 rev/min to 382 rev/min, design the spring by calculating the spring constant k of each spring. The springs are attached to the inner ends of the slots and to the blocks.
A 256-lb block is released from rest when the spring is unstretched. The drum has a weight of 76 lb and a radius of gyration of kO = 0.9 ft about its center of mass O. The coefficient of stiffness of the spring is k=78 lb/ft. The radius of the drum are: rin=0.485ft and rout=0.82ft. Find the velocity of the block after it has descended d=4 feet.
A spool of mass 60 kg is supported on two rollers at A and B as shown in FigureQ1(c). Neglect the mass of the inelastic cable, friction and the mass of therollers at A and B. Knowing that a constant pulling force P is applied in order tounwind 6 m of cable in 3 s starting from rest. The radius of gyration for the spoolis (604) mm, Appendix Ashows the examples of identifying the radius of gyration using student ID.(i) Determine the angular acceleration of the spool. (ii) Determine the pulling force P. (iii) Explain with calculation on ways to increase the acceleration of cablebeing pulled. [
Q1: A cylindrical body has a mass Mand outer radius R (the moment of inertia I I= 1 2 MR^ 2 ) starts to roll from rest (upper position) down on an inclined surface. If the effect of friction force was ignored, determine the linear speed of the cylinder when it hits level ground a height h lower.
The uniform 140-lblb beam is initially at rest when the forces are applied to the cables. Set FAFAF_A = 70 lblb and FBFBF_B = 190 lblb .(Figure 1) Determine the magnitude of the acceleration of the mass center at this instant. Determine the angular acceleration of the beam at this instant.
A motorcycle and rider have a combined mass of 350kg. The each wheel has a mass of 20kg with the diameter of 500 mm. The rider accelerates from 5m/s to 25m/s over a distance of 100m, whilst climbing a hill of slope 1 in 20. Identify the magnitude and effect of gyroscopic reaction torque by calculating the angular velocity and power as the motorcycle ascends the incline when the motorcycle and rider travel at 80 km/h around a left-hand bend of road with the radius 30 m.Explain the effects of energy transfer in mechanical systems (e.g. gears, pulley or flywheel) with uniform acceleration present.