The system is made up of the 1-m, 8.0-kg uniform rod AB and the two uniform disks (each of 0.17 m radius and 1.5 kg mass). If the system is released from rest when 0= 78 , when rod AB has just become horizontal, determine the ratio between the WB angular velocities of disk Band rod AB, Assume the disks roll without slipping. WAB Your answer must include 2 places after the decimal point. Please pay attention: the numbers may change since they are randomized. Take g = 9.81 m/s². В A A Your Answer:

The system is made up of the 1-m, 8.0-kg uniform rod AB and the two uniform disks (each of 0.17 m radius and 1.5 kg mass). If the system is released from rest when 0= 78 , when rod AB has just become horizontal, determine the ratio between the WB angular velocities of disk Band rod AB, Assume the disks roll without slipping. WAB Your answer must include 2 places after the decimal point. Please pay attention: the numbers may change since they are randomized. Take g = 9.81 m/s². В A A Your Answer:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 100-kg spool is resting on the inclined surface for which the coefficient of kinetic friction is μk = 0.13. The radius of gyration about the mass center is kG = 0.22 m Determine the angular velocity of the spool, measured clockwise, when t = 7 s after it is released from rest. Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise
The T-shaped body of total mass m = 6.5 kg is constructed of uniform rod. If it is released from rest while in the position shown, determine the vertical force reaction at O as it passes the vertical position (124° after release). The distance b is 1.04 m.
The plank AB has a mass of 7 kg. The rollers D and E are each of mass 5kg and are 0.5 m in diameter. The plank is released from rest with roller D under the end A and the roller E, under the mass center C. assuming no slipping, determine the velocity of the plank when roller E is under end B.
The 2.5-kgkg rod ACBACB supports the two 4.1-kgkg disks at its ends. If both disks are given a clockwise angular velocity (ωA)1=(ωB)1=4.6rad/s(ωA)1=(ωB)1=4.6rad/s while the rod is held stationary and then released, determine the angular velocity of the rod after both disks have stopped spinning relative to the rod due to frictional resistance at the pins AA and BB. Motion is in the horizontal plane. Neglect friction at pin CC.
The 7.5-lb disk A has a radius r A = 6 in. and is initially at rest. The 10-lb disk B has a radius r B = 8 in. and an angular velocity w0 of 900 rpm when it is brought into contact with disk A. Neglecting friction in the bearings, determine (a) the final angular velocity of each disk, (b) the total impulse of the friction force exerted on disk A.
The 2.07-kg uniform slender bar has a 0.94-kg particle attached to its end. The spring constant is k = 644 N/m and the distance b = 165 mm. If the bar is released from rest in the horizontal position shown where the spring is unstretched, determine the maximum angular deflection θmax of the bar. Also determine the magnitude of the angular velocity at θ = θmax/2. Neglect friction..
AB bar, negligible weightmovement on the surface indicated by the wheelsis doing. The bar is at rest when θ = 0°is being released. A and B when θ = 30°Find the velocities of the points.
Rod OA rotates counterclockwise at a constant angular rate θ˙ = 4 rad/s. The double collar B is pin-connected together such that one collar slides over the rotating rod and the other collar slides over the circular rod described by the equation r=(1.6cosθ)m. Both collars have a mass of 0.55 kg . Motion is in the horizontal plane. Determine the magnitude of the force which the circular rod exerts on one of the collars at the instant θ = 45∘ Determine the magnitude of the force that OA exerts on the other collar at the instant θ = 45∘
The double pulley consists of two wheels which are attached to one another and turn at the same rate. The pulley has a mass of 15 kg and a radius of gyration kO=110mm. If the block at A has a mass of 40 kg, determine the speed of the block in 3 s after a constant force F=2kN is applied to the rope wrapped around the inner hub of the pulley. The block is originally at rest. Neglect the mass of the rope.
The homogeneous sphere with mass m is held 1 m above the horizontal plane and rotates with an angular velocity of 30 rad/s clockwise. The sphere is then released and falls impacting the ground below at A. Determine the velocity of the centre of mass of the sphere after it bounces. Assume the ground is rough so no slipping occurs, and the coefficient of restitution is 0.9. Solve all questions using Impulse and Momentum methods
If the cord is subjected to a horizontal force of P = 150 N, and gear is supported by a fixed pin at O,determine the angular velocity of the gear and the velocity of the 20-kg gear rack in 4 s, starting from rest. The mass of the gear is 50 kg and it has a radius of gyration of k0 = 125 mm. Assume that the contact surface between the gear rack and the horizontal plane is smooth.
The 10-gg bullet having a velocity of vvv = 750 m/sm/s is fired into the edge of the 4-kgkg disk as shown. The disk is originally at rest. The rod ABAB has a mass of 3 kg Determine the magnitude of the angular velocity of the disk just after the bullet becomes embedded into its edge. Calculate the angle θθ the disk will swing when it stops.