The tensile load on a rod stretched between two fixed points is 4500 N. The temperature is 25°C. The cross sectional area of the rod is 170 mm2. Determine the stress that will be experienced by the rod at -10°C. The linear expansion coefficient is 11.7 x 106 mm/mm-°c and the modulus of elasticity is 200 GPa. Express your answer in MPa.

The tensile load on a rod stretched between two fixed points is 4500 N. The temperature is 25°C. The cross sectional area of the rod is 170 mm2. Determine the stress that will be experienced by the rod at -10°C. The linear expansion coefficient is 11.7 x 106 mm/mm-°c and the modulus of elasticity is 200 GPa. Express your answer in MPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.1P: The rails of a railroad track are welded together at their ends (to form continuous rails and thus...

See similar textbooks

Similar questions

A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the figure. The width of the plate is h = 12.0 in. Measurements show that the normal strains in the x and v directions are s = 427 × 10-6 and s = 113 × l0-6, respectively. With reference to part b of the figure. which shows a Iwo-dimensional view of the plate. determine the following quantities. (a) The increase .d in the length of diagonal Oil. (b) The change . in the angle between diagonal Oti and the x axis, (c) The shear strain y associated with diagonals Oil and cf(that is. find the decrease in angle ced).
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?
Q2 A rod is 3m long at a temperature of 15°C. Find the expansion of the rod, when the temperature is raised to 95°C. If this expansion is prevented, find the stress induced in the material of the rod. Take E=1x105 N/mm2 and α=0.000012/°C.
A copper rod with 0.15 cm diameter is enclosed by a steel tube that has an outside diameter of 0.3 cm and an internal diameter of 0.2 cm. The assembly is fixed at each end. Determine the stresses in the rod and tube if the temperature is at 220oC; at 10oC, there is no longitudinal stress. Based on laboratory results for steel, E = 2.1 x 105 N/mm2, a = 11x10-6/oC, and for copper, E = 1 x 105 N/mm2, a = 18x10-6/oC
Determinethe change in diameter of a circular steel rod axially loaded in compression where the diameter is 4.8cm and the axial strain of –0.0021 with poisson's ratio of 0.27.
Question 3 - Strain Energy A brass tube with an outside diameter of 20 mm and 4 mm wall thickness is 80 mm long.It is joined to the end of a solid brass rod with a diameter of 20 mm and 120 mm long toform a compound assembly. This assembly is subjected to tension due to a mass of 150kg moving at a speed of 0.4 m/s.3.1. Determine the stresses induced in the rod and the tube respectively.3.2. Determine the change in length of each part, as well as the total change in length ofthe assembly.3.3 Determine the equivalent impact load (in kg) required to have the same effect(produce the same amount of energy) if falls freely from a height of 10 cm onto acollar attached to the bottom of the assembly if the assembly is vertically attachedat its top.3.4 How much strain energy is absorbed by each section of the assembly?(For brass: E = 100 GPa and α = 18×10-6/ 0C)
Q2 A rod is 3m long at a temperature of 15°C. Find the expansion of the rod, when the temperature is raised to 95°C. If this expansion is prevented, find the stress induced in the material of the rod. Take E=1x105 N/mm2 and α=0.000012/°C. Kindly solve it with details
A 200 mm long, stress free rod at room temperature is held between two immovable rigid walls. The temperature of the rod is uniformly raised by 250°C. If the Young's modulus and coefficient of thermal expansion are 200 GPa and 1×10^-5/°C respectively, the magnitude of the longitudinal stress (in MPa) developed in the rod is _______ A. 600 MPa B. 200 MPa C. 500 MPa D. 250 MPa
A steel bar is placed between two copper bars, each having the same area and length as steel bar at 20℃. A this stage, they are rigidly connected together at both the ends. When the temperature is raised to 320℃, the length of the bars increases by 1.5mm. Determine the original length and final stresses in the bars. Steel: Coefficient of expansion = 0.000012/℃; Es = 210 GN/m^2 Copper: Coefficient of expansion = 0.0000175/℃; Ec = 100 GN/m^2
An engineering machine component operating in a high temperature environment consists of a copper pipe having a cross-sectional area of 2 000 mm2 and 0.3 m long, which is placed between two rigid caps. Four M22 steel bolts are symmetrically arranged around the tube and parallel to the axis of the tube and are lightly tightened. 3.1 Find the stress in the pipe and the bolts if the temperature of the assembly is increased from 25 0C to 95 0C. 3.2 What load will each bolt carry at the raised temperature? 3.3 Make a neat sketch of the assembly. (ESt = 200 GPa, ECu = 100 GPa, αSt = 12 × 10-6/ oC, αCu = 16 × 10-6/ oC)
A steam pipeline measures 20 m at a temperature of 20 °C. The pipeline carries superheated steam at a temperature of 300 °C. If 80% of the possible expansion of the pipe is prevented from taking place, find the stress induced in the material of the pipe having E =210 kN/mm 2 and coefficient of thermal expansion = per °C.