Use the manning's equation above to find the streamflow rate (Q) under the following conditions: a. Rectangular canal b. Earth, winding, with vegetation (n) c. River top width (B) - 1000 m d. River depth (Y) =2 m e. River bed slope (S) =0.01 m/m 1. Conversion constant (k) =1 m/s

Use the manning's equation above to find the streamflow rate (Q) under the following conditions: a. Rectangular canal b. Earth, winding, with vegetation (n) c. River top width (B) - 1000 m d. River depth (Y) =2 m e. River bed slope (S) =0.01 m/m 1. Conversion constant (k) =1 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Cipolletti weir, popular in irrigation systems, is trapezoidal,with sides sloped at 1:4 horizontal to vertical, as in Fig. The following are flow-rate values, from the U.S.Dept. of Agriculture, for a few different system parameters. Use this data to correlate a Cipolletti weir formula with areasonably constant weir coefficient.
Pebbles dropped successively at the same point, into awater channel flow of depth 65 cm, create two circularripples, as in Fig.. From this information estimate(a) the Froude number and (b) the stream velocity.
You’ve sent your assistant out to measure the flow properties of a frictionlessrectangular flat channel. Your assistant returns with measurements for the depth (d2 =1.4 m), the specific discharge (q2 = 10.0 m2/s), and (somehow) the height of the energygrade line at 4.0 meters all at the downstream cross section. They haven’t done aspectacular job leaving you to solve for d1, q1, V1, and V2. There are two potentialanswers for d1 and V1.
In Fig. , free discharge, a gate opening of 0.72 ft willallow a fl ow rate of 30,000 gal/min. Recall y1 = 6 ft and thegate width b = 8 ft. Suppose that the gate is drowned with y2 = 4 ft. What gate opening wouldthen be required?
UsingFig. P6.27. All parameters are constant except the uppertank depth Z(t). Find an expression for the flow rate Q(t) asa function of Z(t). Set up a differential equation, and solvefor the time t0 to drain the upper tank completely. Assumequasi-steady laminar flow.
In flood stage a natural channel often consists of a deepmain channel plus two floodplains, as in Fig. Thefloodplains are often shallow and rough. If the channel hasthe same slope everywhere, how would you analyze thissituation for the discharge? Suppose that y1 = 20 ft, y2 =5 ft, b1 = 40 ft, b2 = 100 ft, n1 = 0.020, and n2 = 0.040,with a slope of 0.0002. Estimate the discharge in ft3/s.
I have tried by assuming Vdot value, Put value in 4equation that I got, 1. Flow rate equation 2. Reynold number equation 3. Haaland's equation 4. H(available) = H(required) I tried to solve it by iteration, However, I can't figure out, which value I could use with the iteration technique
2.Water flows through a rectangular channel with a width b = 2 m and a height (Pw) = 1 m, the flow rate ranges from Qmin = 0.02 m^3/s and Qmax = 0.60 m^3/s. This flow rate is measured using Rectangular sharp-crested weir Triangular sharp-crested with = 90^o Broad-crested weir Plot onto the graph Q = Q(H) for each type of weir and give your analysis which type of weir is most appropriate to apply
Consider the one-dimensional, incompressible flow through the circular channel shown. The velocity at section 1 is given by U5U0 1U1 sin ?t, where U0 520 m/s, U1 5 2 m/s, and ? 5 0.3 rad/s. The channel dimensions are L51 m, R1 50.2 m, and R2 50.1 m. Determine the particle acceleration at the channel exit. Plot the results as a function of time over a complete cycle. On the same plot, show the acceleration at the channel exit if the channel is constant area, rather than convergent, and explain the difference between the curves.
The figure shown below is a series pipeline system used to draw a fluid from a lower source open tank to a higher destination open tank . The flow and geometric layout for the system are listed below: Fluid: water Volume flow rate: Q=0.015 m3/s Elevation difference: h=8.0m of two free surfaces Suction line: DN100 Sch. 40 Steel pipe Length: Ls=2.0 m Valve1: hinged disc type foot valve Entrance type: well-rounded Discharge line: DN80 Sch. 40 Steel pipe Length: Ld=100 m Valve2: full open gate valve Elbows: 90ο long radius elbow (2) Select all energy loss types between section 1 and 2_________ A. Minor loss for the two elbows B. Friction loss in suction line C. Minor loss for Valve 1 D. Entrance loss E. Exit loss F. Friction loss…
The figure shown below is a series pipeline system used to draw a fluid from a lower source open tank to a higher destination open tank . The flow and geometric layout for the system are listed below: Fluid: water Volume flow rate: Q=0.015 m3/s Elevation difference: h=8.0m of two free surfaces Suction line: DN100 Sch. 40 Steel pipe Length: Ls=2.0 m Valve1: hinged disc type foot valve Entrance type: well-rounded Discharge line: DN80 Sch. 40 Steel pipe Length: Ld=100 m Valve2: full open gate valve Elbows: 90ο long radius elbow (1) Select the simplified general energy equations for section 1 and 2_________ A. B. C. D.
Gentlemen, please check and help me with question #3 Tank filled with water and orifice diameter of 3 cm in the bottom. Height between centre of orifice and water level 3 m. Coefficient of discharge - 0.64, coefficient of velocity- 0.97. Find: 1. Actual jet velocity? This one I know how to do. V(actual) = square root from 2gH 2. Jet diameter? This one I know as well. Coefficient of contraction= coefficient of discharge/ coefficient of velocity Diam of jet we will find from formula: Coefficient of contraction = (diameter of jet/diameter of orifice)^2 3. How long will it take for jet to be established?