B2 The tension in the belt is 22 lb (Figure 1).Figure8 in.in.-F₁1 of 1Part ADetermine the moment of the force F₁ about the pin at A.Express your answer in pound-inches to three significant figures. Enter positive value ifthe moment is counterclockwise and negative value if the moment is clockwise.195| ΑΣΦ | 11 | vec(M₁) ASubmitPart BRequest Answer(M₂)A-?Determine the moment of the force F₂ about the pin at A.Express your answer in pound-inches to three significant figures. Enter positive value ifthe moment is counterclockwise and negative value if the moment is clockwise.VAX i veclb-in.?lb-in.

0Given data:- Tension in the belt =22 lb To Find:- Moment about point A of F1 Moment about point A…

The tension in the belt is 22 lb (Eigure 1). Figure 8 in. ATHE 1 of 1 > Determine the moment of the force F₁ about the pin at A. Express your answer in pound-inches to three significant figures. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise. (M₁)A- Submit Part B VAXtvec (M₂)A- Request Answer ? Determine the moment of the force F, about the pin at A. Express your answer in pound-inches to three significant figures. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise. VAX it vec lb-in. ? lb-in.

The tension in the belt is 22 lb (Eigure 1). Figure 8 in. ATHE 1 of 1 > Determine the moment of the force F₁ about the pin at A. Express your answer in pound-inches to three significant figures. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise. (M₁)A- Submit Part B VAXtvec (M₂)A- Request Answer ? Determine the moment of the force F, about the pin at A. Express your answer in pound-inches to three significant figures. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise. VAX it vec lb-in. ? lb-in.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.64P: The two main cables of the Akashi Kaikyo suspension bridge in Japan have a span L=1990m and a sag...

See similar textbooks

Similar questions

Determine the magnitude of moment (Nm) of the 383-N force about point A if x = 0.55 m , y = 0.69 m, and θ = 41.4ᵒ. Round off only on the final answer expressed in 3 decimals. Instead of units, type either POSITIVE or NEGATIVE to indicate the direction of moment which is consistent with the sign convention discussed on lectures. Sample answers are 12.908 POSITIVE or 12.908 NEGATIVE
Take that w0 = 4.6 kN/m. Replace the loading by an equivalent force. Express your answer to three significant figures and include the appropriate units. Enter positive value if the force is upward and negative value if the force is downward. Replace the loading by a couple moment acting at point O. Include clockwise or counterclockwise.
The compound beam is supported by a roller at point C, fixed at point A, and the two sections are pinned at point B. It is subjected to a free couple moment M, a distributed load with maximum load intensity w, and a concentrated force F. If the distributed load w = 0.6 kN/m, the concentrated force F = 0.6 kN, and the free couple moment M = 0.8, determine the magnitude of the support reaction (in kN) at pin B. Answer must include 2 places after the decimal point.
The bent rod is supported at points A, B and C by smooth journal bearings, and is subjected to force F. If dimensions a = 2.3 m, b = 1.5 m, c = 0.6 m, and d = 2.5 m, and the force F is {-2i + 9j - 3k} kN, determine the magnitude of the moment (in kN⋅m) caused by force F about point A. Answer must include 2 places after the decimal point.
The forklift supports the engine. Determine the force that generates this load on element DB. Write your answer in Newtons. Consider Engine mass = 114 kg a = 1.47 m b = 1.81 m
A vertical load P = 800 lb applied to the tripod shown in the figure, causes a compressive force of 256 lb in leg AB and a compressive force of 283 lb in leg AC. Determine the force in leg AD and the coordinates xD and zD of its lower D. Answers: AD = 433 lb; xD = 4ft; zD = 1 ft
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
A bent pipe is connected by a thrust bearing and a cable asshown. If a Force, F = 195 lb, is applied, what are the reactions at the thrust bearing and in the cable. The dimensions shown are a = 7.2 ft, b = 6.2 ft, and c = 4.6 ft.
Determine the magnitude of the pin force at A.Assume W = 755 lb, a = 5.4 ft, b = 3.9 ft, r = 7 in.
Use the picture to solve these questions 1-The magnitude of the moment induce by the load about the Line-EF is _____ kN*mm. 2- The direction of the moment induce by the load about the Line-EF is _____ kN*mm. 3- The direction of the moment induce by the load about the Line-CD is _____ kN*mm. 4- The state of the internal force at the mid-point of Member-BD _____ . Enter "1" for "tension". Enter "2" for "compression" Enter "3" for "torsion" Enter "4" for "neither tension, nor compression, nor torsion 5- The state of the internal force at the mid-point of Member-BF _____ . Enter "1" for "tension". Enter "2" for "compression" Enter "3" for "torsion" Enter "4" for "neither tension, nor compression, nor torsion
The shaft is supported at its ends by two bearings AA and BB and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T1=T1= 585-NN forces act in the -zz direction and the 200-NN and 80-NN forces act in the +yy direction. The journal bearings at AA and BB exert only yy and zz components of force on the shaft. Part A Determine the resultant normal force on the cross section at CC. Express your answer to three significant figures and include appropriate units. NC= values ? NC= units? Determine the resultant shear force in the yy direction on the cross section at CC . Express your answer to three significant figures and include appropriate units. (VC)y Values ? (VC)y units ?
The two main cables of the Akashi Kaikyo suspension bridge in Japan have a span L=1990m and a sag H=223m. The loading on each cable is w0=444.7kN/m (without traffic) along the horizontal. Determine the corresponding maximum force in one of the cables.