The tension on the Achilles tendon with a diameter of 10 mm is 4000 N ,if the length of the Achilles tendon is L = 200 mm, what is the lengthening of tendon and PE by two methods. 604 40- 20- Strain () Stress-strain Achilles tendon Stress (newtons per square milimetre

The tension on the Achilles tendon with a diameter of 10 mm is 4000 N ,if the length of the Achilles tendon is L = 200 mm, what is the lengthening of tendon and PE by two methods. 604 40- 20- Strain () Stress-strain Achilles tendon Stress (newtons per square milimetre

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 68P: An aluminium (=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the...

See similar textbooks

Related questions

Q: 200 150 100 --- Material X 50 Material Y • Material Z 0.000 0.005 0.010 0.015 0.020 0.025 Strain (ɛ)…

A: SOlution: Given that d = 3 mmL =1.25 ftstrain ε = 0.045

Q: 14. Two circular rods, one steel and the other copper, are joined end to end. Each rod is 0.750 m…

Q: Evaluate Young’s modulus for the material whose stress– strain curve is as shown.

A: Solution: Young’s modulus for the material whose stress– strain curve is as shown has given by,

Q: stress 0.02 0.018 0.016 0.014 0.012 0.01 0.008 0.006 0.004 0.002 0.05 0.1 0.15 0.2 0.25 0.3 0.35…

Q: A 20 g rectangle block of aluminium is 35 cm by 45 cm by 15 cm when unstressed. A force is applied…

A: Given information: The mass of the rectangle aluminum block (m) = 20 g = 0.02 kg The dimensions of…

Q: This force is a force that is applied along the plane of an area rather than at right angles to it.…

A: 15 Shear force is a type of force that is applied along the plane of an area rather than at right…

Q: 3 x 10, then find out the percentage change in its volume. is applied on it due to which it suffers…

A: Poisson's ratio is defined as the ratio between transverse strain and longitudinal strain.

Q: Assume a person's mass is 54.0 kg and each of her shoes has an area of 195 cm². F on her feet if her…

Q: An aluminium wire, initially 2.45 m long and diameter of 1.5 mm, is suspended from a rigid support…

Q: Problem 2 ( )A 200 Kg load is hung on a wire of length 4 m, and a cross- sectional area A=4 10- m2.…

A: Stress. = Force ÷ area. Force =weight of load= mg = 200kg×9.8m/s2 = 196N Force = 196N Area = 4 ×…

Q: *67. A gymnast does a one-arm handstand. The humerus, which is the upper arm bone (between the elbow…

Q: A 0.800 m-long metal wire has a circular cross section of diameter 0.900 mm. One end of the wire is…

A: Given that, Length of the wire(L)= 0.8 m Diameter (d)= 0.9× 10-³ m So, radius (r)= (0.9×10-³)/2=…

Q: A heavy crate with weight 4900 N hangs from a thick nylon rope. The rope has a cross-sectional area…

A: Solution: Given that Weight W = 4900 N Area A = 1.4x10-4 m2 youngs modulus E =3.7x109 N/m2

Q: A 1.4 x 10-3-kg house spider is hanging vertically by a thread that has a Young's modulus of 4.5 x…

Q: H = 8 cm L = 4 cm α = 50° t = 5 mm The strain value of the structure in the same direction as a…

A: Write the given values of this problem. H=8 cmL=4 cmα=50T=5 mm∈x=0.26 mm/mm

Q: 200 150 100 -- Material X 50 Material Y • Muterial Z 0.000 0.005 0.010 0015 0.020 0.025 Strain (e)…

A: young's modulus of material y=stressstrainy=(150-15)MPa0.02-0.001y =1350.019y = 7105.26 MPa7105.26

Q: 3. The cable and boom shown in Fig. P-308 support a load of 60o lb. Determine the tensile force T in…

Q: Assume Young's modulus for bone is 1.50 x 1010 N/m2. The bone breaks if stress greater than a= 15086…

A: Given, Young's modulus = Stress = Radius = 0.01 m

Q: 57. The drawing shows a 160-kg crate hanging from the end of a steel bar. The length of the bar is…

A: Mass of the crate, The length of the bar, The cross-sectional area of the bar, The shear…

Q: 2. A human biceps(upper arm muscle) may exert a force of the order of 600N (about 135 Ib) on the…

A: Tensile stress is defined as the force per unit area produced in the body as a result of an…

Q: A square steel plate is 10.0 cm on a side and 0.500 cm thick. (a) find the shear strain that results…

A: (a) Find the shear strain applied to each of the four sides of the square steel plate.…

Q: 2. The area of the upper face of a rectangular block is 0.5m x 0.5 m and the lower face is fixed.…

A: Given: The area of the upper surface is A=0.5 m×0.5 m=0.25 m2 The height of the block is h=1…

Q: 3. A brass rod with a length of 1.40 m and a cross- sectional area of 2.00 square cm is fastened end…

A: Stress is defines as the force per unit area of a material. i.e. Stress = Forcecross sectional area…

Q: 61. •Medical In regions of the cardiovascular system where there is steady laminar blood flow, the…

A: SOlution: given that Shear stress on cells lining the walls of the blood vessels is equal to 20…

Q: nal area of 3.00cm2 has an elastic limit of 2.40x108 Pa. Find the maximum upward acceleration that…

A: Given-Cross-sectional area A= 3.00cm2=3×10-4 m2Force is perpendicular to the cross-section of the…

Q: EXample 2: the ankle joint therefore pushes upward on the bottom of the tibia with the force of 2800…

A: Given : R1=1.3 cmR2=2.5 cm

Q: Humans can bite with a force of approximately 810 N. If a human tooth has the Young's modulus of…

A: SOlution: as given F = 810 N E = youngs modulus of bone= A = 1.5 cm2 = 1.5x10-4 m2 L = 1.5 cm =…

Q: Assume Young's modulus for bone is 1.50 x 1010 N/m2. The bone breaks if stress greater than o= 45844…

A: Young's modulus is Y= 1.5×10¹⁰ N/m² Maximum stress is σ = 45844 N/m² Effective radius of the bone…

Q: If the human bone fractured with stress 120 N/mm 2 then the maximum tension on the bone with an area…

Q: A 1.3 x 10-3-kg house spider is hanging vertically by a thread that has a Young's modulus of 4.4 x…

Q: The force applied to the handle of the rigid lever arm causes the arm to rotate clockwise through an…

Q: Humans can bite with a force of approximately 792 N. If a human tooth has the Young's modulus of…

A: Force exerted (F) = 792 N Cross sectional area (A) = 1.3 cm2= 0.00013 m2Length of bone (L) = 1.7cm =…

Q: A wire has a mass 5.3 g and length 2.50m. A force of 50 N can extend it by 2.3 mm. Determine (a) the…

A: we know that density = mass/volume 2.7x103=5.3x10-3A x 2.5Area = A = 7.85 x10-7 m2

Q: Humans can bite with a force of approximately 795 N. If a human tooth has the Young's modulus of…

A: Young's modulus is defined as the ability of a material to withstand the change in length due to…

Q: A bone in a woman's leg has an effective cross-sectional area of 3.07 cm². If the bone is 36.1 cm…

A: Compressive strength of human bone is CS= Cross- sectional area of the bone, A= 3.07 cm2 = Length of…

Q: Humans can bite with a force of approximately 807 N. If a human tooth has the Young's modulus of…

A: The equation for Young's modulus is given by, Y=σe (1) Here, σ is the stress and e is the strain.…

Q: Q2.8/ If the tensile stresses generated in a copper rod after the influence of external forces (ot…

A: Given data: The tensile stress in the material is σt=2158.2104 N/m2. The longitudinal strain is…

Q: Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB. If…

A: Given Data: The angle is, θ=0.5o. The length AC is, AC=600 mm The length BC is, BC = 800 mm.…

Q: Problem Solving... A torsion test shows that the shear modulus of an aluminum specimen is 4.60 x…

Q: Assume a person's mass is 62.0 kg and each of her shoes has an area of 220 cm?. F What is the…

Q: " The femur is a bone in the leg whose minimum cross-sectional area is about 4.0 X 10-ª m². A…

Q: determine the change in the tooth's length

A: Given data: The force applied during bite is: F = 796 N The cross-sectional area of tooth is: A…

Q: The dimensions of the Tensile Strain is Select one: a. MLT-1 b. ML-1T-2 c. Dimensionless d. ML2T-2…

A: The strain is the ratio of the change in dimensions to the original dimension.

Q: *69. ssm A 1.0 × 10-3-kg spider is hanging vertically by a thread that has a Young's modulus of 4.5…

Q: 1) If the radius of cables AB and CD are 5mm and modulus of elasticity is 20GPA, calculate the…

A: Given : Radius of the cable, r =5 mm = 0.005 m Force, F = 1000 N Modulus of elasticity, e = 20Gpa

Q: A sign (mass 2300 kg) hangs from the end of a vertical steel girder with a cross-sectional area of…

A: Given value--- mass = 2300 kg. Area = 0.01 m2 . Elastic modulus = 2 × 1011 N/m2. We have to…

Q: If the same force F pulls on two cylindrical rods of the same material, which has a greater change…

A: Y=F/A∆L/L=FLA∆L∆L=FLAY=FLπr2Y

Q: Assume Young's modulus for bone is 1.50 x 100 N/m². The bone breaks if stress greater than d= 40607…

A: Young modulus, Y=1.50× 1010 N/m2 Maximum stress, σ=40607 N/m2 Radius, r = 0.01 m

Question

None

The tension on the Achilles tendon with a diameter of 10 mm is 4000 N ,if the length of the
Achilles tendon is L = 200 mm, what is the lengthening of tendon and PE by two methods.
604
40-
20-
Strain ()
Stress-strain Achilles tendon
Stress (newtons per square milimetre)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

(a) When water freezes, its volume increases by 9.05% (that is, V/V0=9.05102 ). What force per unit area is water capable of exerting on a container when it freezes? (It is acceptable to use the bulk modulus of water in this problem.) (b) Is it surprising that such forces can fracture engine blocks, boulders, and the like?
A company is testing a new material made of recycled plastic for use in construction. Figure P14.48 is a graph of the stress as a function of strain for this material. Find Youngs modulus for this material and compare your result with the data for conventional building materials listed in Table 14.1.
Normal forces of magnitude 1.0106N are applied uniformly to a spherical surface enclosing a volume of a liquid. This causes the radius of the surface to decrease from 50.000 cm to 49.995 cm. What is the bulk modulus of the liquid?
Review. A wire of length L, Youngs modulus Y, and cross-sectional area A is stretched elastically by an amount L. By Hookes law, the restoring force is kL. (a) Show that k = YA/L. (b) Show that the work done in stretching the wire by an amount L is W=12YA(L)2/L.
A horizontal, rigid bar of negligible weight is fixed against a vertical wall at one end and supported by a vertical string at the other end. The bar has a length of 50.0 cm and is used to support a hanging block of weight 400.0 N from a point 30.0 cm from the wall as shown in Figure P14.81. The string is made from a material with a tensile strength of 1.2 108 N/m2. Determine the largest diameter of the string for which it would still break. FIGURE P14.81
Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?
A 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a second 100-N weight is added to the wire, it stretches 3.0 mm. The diameter and the length of the wire are 1.0 mm and2.0 m, respectively. What is Young’s modulus of the metal used to manufacture the wire?
What Is Static Equilibrium? Problems 13 are grouped. 1. C A ball is attached to a strong, lightweight rod (Fig. P14.1). The rod is supported by a horizontal pin near the top. The ball is at rest. Is the ball in static equilibrium? If not, why not? If so, which type of equilibrium is itstable, unstable, or neutral? Hint: What would happen if you displaced the ball slightly? FIGURE P14.1
A uniform rope of cross-sectional area 0.50cm2 breaks when the tensile stress in it reaches 6.00106N/m2 . (a) What is the maximum load that can be lifted slowly at a constant speed by the rope? (b)What is the maximum load that can be lifted by the rope with an acceleration of 4.00m/s2 ?
A high-speed lifting mechanism supports an 800.-kg object with a steel cable that is 25.0 m long and 4.00 cm2 in cross-sectional area. (a) Determine the elongation of the cable. (b) By what additional amount does the cable increase in length if the object is accelerated upward at a rate of 3.0 m/s2? (c) What is the greatest mass that can be accelerated upward at 3.0 m/s2 if the stress in the fable is not to exceed the elastic limit of the cable, which is 2.2 108 Pa?
A high-speed lifting mechanism supports an 800.-kg object with a steel cable that is 25.0 m long and 4.00 cm2 in cross-sectional area. (a) Determine the elongation of the cable. (b) By what additional amount does the cable increase in length if the object is accelerated upward at a rate of 3.0 m/s2? (c) What is the greatest mass that can be accelerated upward at 3.0 m/s2 if the stress in the fable is not to exceed the elastic limit of the cable, which is 2.2 108 Pa?
Calculate the pressure due to the ocean at the bottom of the Marianas Trench near the Philippines, given its depth is 11.0 km and assuming the density of sea water is constant all the way down. (b) Calculate the percent decrease in volume of sea water due to such a pressure, assuming its bulk modulus is the same as water and is constant. (c) What would be the percent increase in its density? Is the assumption of constant density valid? Will the actual pressure be greater or smaller than that calculated under this assumption?