The thin rod has a weight W = 49.05 N applied at its center of gravity and rests against the rough floor and smooth wall. The coefficient of static friction at 'A' is HA= 0.25.Assume impending motion at 'A', What would be the friction force at "A': Select one: O a. 49.05 N O b. 5 N c. 24.52 N d. 12.26 N

The thin rod has a weight W = 49.05 N applied at its center of gravity and rests against the rough floor and smooth wall. The coefficient of static friction at 'A' is HA= 0.25.Assume impending motion at 'A', What would be the friction force at "A': Select one: O a. 49.05 N O b. 5 N c. 24.52 N d. 12.26 N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.4P: The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical...

See similar textbooks

Similar questions

The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
The uniform bar of weight W is supported by a ball-and-socket joint at A and rests against a vertical wall at B. If sliding impends when the bar is in the position shown, determine the static coefficient of friction at B. [Hint The direction of impending sliding is tangent to the dashed circle (the potential path of motion of point B).]
Determine the smallest coefficient of static friction at A for which the system shown is self-locking (can support the force P of any magnitude). Neglect the weight of bar AB.
The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
The cone clutch transmits the torque C through a conical friction surface with cone angle . The inner and outer radii of the friction surface are a and b, respectively. The left half of the clutch is keyed to the shaft, and the right half drives a machine (not shown) through a gear attached to its outer rim. Assuming uniform pressure on the friction surface, show that the maximum torque that can be transmitted by the clutch is
The screw of the carjack has a pitch of 0.1 in. and a mean radius of 0.175 in. Note that the ends of the screw are threaded in opposite directions (right- and left-handed threads). The coefficient of static friction between the threads is 0.08. Calculate the torque C0 that must be applied to the screw in order to start the 1200-1b load moving (a) upward; and (b) downward.
A plant is 10m ong is placed on a horizonta positin wth ts two ends resting on to inclined planed. Angle of friction on all surfaces is 20 degrees. 1. VAlue of x when plank will start to the side? 2. if P=100kn what is the reaction of A? 3. if P=100kn what is the reaction of B?
What couple M is needed to cause the wheel of weight W and radius r shown in Fig 9.41 to have impending motion? The coefficient of friction for all surfaces is μ. Give solujtion. [Ans. M=μWr (1+μ)/(1+μ2)]