A square threaded screw of mean diameter 25 mm and pitch of thread 6 mm is utilised to lift a weight of 10 kN by a horizontal force applied at the circumference of the screw. Find the magnitude of the [Ans. 966 N] force if the coefficient of friction between the nut and screw is 0.02. A bolt with a square threaded screw has mean diameter of 25 mm and a nitch of 3 mm It carries an 2.

A square threaded screw of mean diameter 25 mm and pitch of thread 6 mm is utilised to lift a weight of 10 kN by a horizontal force applied at the circumference of the screw. Find the magnitude of the [Ans. 966 N] force if the coefficient of friction between the nut and screw is 0.02. A bolt with a square threaded screw has mean diameter of 25 mm and a nitch of 3 mm It carries an 2.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.72P

See similar textbooks

Similar questions

The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The test specimen AB is placed in the grip of a tension-testing machine and secured with a wedge. The coefficient of static friction at both surfaces of the specimen is s. If the wedge angle is =18, determine the smallest s for which the grip is self-locking (no slipping takes place regardless of the magnitude of the force P). Neglect the weight of the wedge.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
A 1.1-kg disk A is placed on the inclined surface. The coefficient of static friction between the disk and the surface is 0.35. Is the disk in equilibrium if P=5.5N and =30?
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
A wedge is used to prop up the 6000-lb block of marble. The wedge angle is =30, and the angle of static friction is s=12 between all contact surfaces. Determine the smallest force P that would prevent the wedge from sliding out.
The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
Determine the smallest horizontal force P that must be applied to block B to cause impending motion. The angles of static friction are 15 between the blocks and 30 between the blocks and the ground.
Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
Refer to Fig 33. The homogenous body A weighs 120 lb. The coefficients of frictions are 0.30 between A and the plane and 2/pi between the rope and the drum. What value of W will cause motion of A to impend? Give solution. (Ans. W= 81.5 lb)
Problem 4. A.) If the uniform concrete block has a mass of 500 kg, determine the smallest horizontal force P needed to movethe wedge to the left. The coefficient of static friction between the wedge and the concrete and the wedge and the floor is 0.3. The coefficient of static friction between the concrete and floor is 0.5.ANSWER: P=1797.52; N=1.80kNB.)Refer to problem number 4. Calculate the followinga.) the angle of friction between the wedge and the concrete and the wedge and the floor.Answer: ?????? ??? ????????= ?????? ??? ?????= 16.7ob.) the coefficient of static friction between the concrete and floor.Answer: ????????? ??? ?????= 263.56o