Answered: The three principal modes of soil…

The three principal modes of soil failure, established by the patterns of the shearing zones. Where does these modes are applicable in which soils type?

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter4: Soil Classification

Section: Chapter Questions

Problem 4.2P: In AASHTO, which group are the following soils likely to fall into? a. A well graded gravel with...

See similar textbooks

Related questions

Q: Define Shear Strength of Unsaturated Soils

A: shear strength is the important characteristic of soil in geotechnical engineering to design the…

Q: 4 ways of dealing with the effect of expansive soil on construction soils

A: Answer:- Expansive soil:- It is a residual soil formed by basalt rock. It contains montmorillonite…

Q: lassify the given soil to be used as highway subgrade material using the AASHTO Method by sing the…

A: This question has been taken from Geo technical engineering

Q: Briefly explain the method of vertical trocars (vertical sand banks) with an illustration?

A: Sand casting, also known as sand molded casting, is a metal casting process characterized by using…

Q: 1) Elaborate and explain briefly the triaxial compression test for the determination of the shearing…

A: Geotechnical engineering, otherwise called geotechnics, is the part of structural designing that…

Q: Why is it expected that the maximum height of capillary rise is greater for fine-grained soils than…

A: Capillary rise is defined as the rise of water through the voids of soil.

Q: Discussion 1. Core cutter method is used for fine-grained soils only. Why? 2. What are the likely…

Q: State an equation for consolidation settlement of a normally consolidated soil?

A: The process by which soil changes its volume with respect of change in pressure is called as soil…

Q: If the soil phi= 36° determine angle of soil failure plane. (Answer Value only and whole number).

A: Phi=36o

Q: Explain the Modulus of Subgrade Reaction and Node Coupling of Soil Effects for Mats ?

A: The term modulus of subgrade reaction is related to the pavement. The modulus of subgrade reaction…

Q: What is critical gradient for coarse-grained soil which has voids ratio of 0.78 and specific gravity…

Q: For the first series of tests, no drainage of pore water occurs, either when the normal load is…

A: Triaxial shear strength test on soil is used to measure the mechanical properties of the soil. In…

Q: 4. After the soil has been pre-consolidated, new piezometric reading indicated that the ground water…

Q: Explain why the new universal soil loss equation includes slope length and slope steepness as…

A: Introduction- The Universal Soil Loss Equation (USLE) calculates average yearly soil loss from…

Q: Assess the suitability of the following soils A, B, C, and D as backfill material invibroflotation.…

A: Solution

Q: The hydraulic gradient for an occurrence where there is a vertically upward flow of water through a…

A: It is required to determine the critical hydraulic gradient. Here, Gs is the specific gravity, and…

Q: Define the type of shear failure of soil is more likely to happen in the case of very dense soil?

A: Shear failure comes in the picture and is evaluated when any building or super structure if built.…

Q: What are the various combinations of the stress state variables that can be used for an unsaturated…

Q: 1) What are the two primary soil types in geotechnical engineering? Also, what are intermediate…

A: Soils are made up of grains (mineral grains, rock pieces, and so on) with water and air in the gaps…

Q: Classify the group index of the soil by AASHTO Classification System using the given data below:…

Q: Describe why effective stress is important when evaluating soil behavior

A: Effective stress Karl Terzaghi, the first person who recognize the importance of effective stress.…

Q: Consider Figure FTR 1 (Taken from Geotechnical Engineer- ing Design, Ming Xiao, strictly for…

A: NOTE - Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: For leossial soil, given Gs = 2.74. Plot a graph of γd (kN/m3) versus liquid limit to identify the…

A: Solution Given Data Gs=2.74γd=14.5 kN/m2

Q: A 10-ft-thick clay layer is drained at the top and bottom. Its characteristics are Cvr = Cv (for…

A: U%=DEGREE OF CONSOLIDATION c=0.042 ft2/dayd=H2=102=5 ftt=0.2 year =0.2×365…

Q: In the given soil profile determine the 6.u and 6' of the points A,B,C and D. Show the variations in…

A: Y

Q: Explain about the Nonlinear soil behavior ?

A: The reduction of the amplification due to shifting of the predominant frequency to lower…

Q: for soils A and B are as follows: NOTE: PI=5% for Soil A (Solution are required) a.) Determine…

A: USCS soil clsssification:iLook at the % passing through sieve no 200=70>50%⇒FINE GRAINED…

Q: Classify the group index of the soil by AASHTO Classification System using the given data below:…

Q: Describe about the Layered Soils Having Different Properties.

A: Properties of layered soil:

Q: What are the most widely used laboratory tests for studying the shear strength of different soils?

A: Shear strength of soil is the capacity to resist shear stress. Shear strength is basically the…

Q: A clay layer with two-way drainage reached 75% consolidationin t years. How long would it take for…

A: To find time required for the soil to consolidate 75%

Q: A stiff-clay channel is to be constructed to convey water with colloidal silts at 200cfs. Based on…

A: Discharge = 200 cfs=5.6633694 m3/sec Bed slope= 0.005 voids ratio = 0.3 For clean and stiff channel…

Q: Describe Stress Path for Tests in Consolidated–Drained Conditions

A: A stress path is a curve which shows the changes in stresses as the load acting on the soil specimen…

Q: (a) nat is 'permeability' oT Soils? (b) What affects the permeability of soils? (c) Why should we…

A: a) what is permeability of soil The property of the soil by which it permits the flow of fluid…

Q: Classify the given soil to be used as highway subgrade material by using the AASHTO method. Sieve…

A: The soil classification is done using AASHTO system.

Q: What types of soil could be best improved by this method.

Q: An embankment will be constructed from borrowed soil. The cross section of the embankment is shown…

A: Given;

Q: C. PI 0.73 (LL- 20) For a sample of dry, cohesionless soil with friction angle, f, the failure plane…

A: Option D= (450)+ ∅/2 is correct

Q: If a representative clay specimen 20 mm thick, under double drainage, took 121 minutes for 90%…

A: Estimate the time in days required for 50% primary compression

Q: SITUATION 9 The result of sieve analysis of three soils is given next. It is required to classify…

A: Step 1:Look at % passing through No 200: 38%>35 so SILT-CLAY MaterialStep…

Q: What are the two types of forces that should be considered in equilibrium analysis for soils?

A: Force Analysis of soil For Analysis any rectangular soil element can be considered under stress.…

Q: How are soils classified on the basis of shear strength? Draw the Mohr-Coulomb strength envelope…

A: Shear strength of soil is defined as the capacity of soil to resist shearing stress. It depends on…

Q: Given that the hydrometer analysis test is based on stoke’s law, what is an inherent error of the…

Q: According to you which is the best software for modeling intraction soil- structure except Abaqus?

A: There are various software using which modeling of soil structure can be done such as: CESAR-LCPC,…

Q: To determine whether the surface zone of the natural soil is adequate for supporting the compacted…

A: Proof-rolling of a sub-grade is defined as the practice in which the responses of the sub-grade to…

Q: Classify the group index of the soil by AASHTO Classification System using the given data below:…

Q: sieve 100 Percent finer than the #40 sieve 92 Percent finer than the #200 sieve

A: We knowGI=0.2F200-35+0.005F200-35LL-40+0.01F200-15PL-10

Q: How does the understanding of the shearing strength of cohesive and cohesionless soils can be…

A: The direct shear test is used to determine the shear strength parameters for a given soil. This test…

Q: O Classify the soil sample A using USCS Method Classify the soil sample B using AASHTO Method a…

A: Given, Sieve analysis data To find - Classification of soil

Q: Determination of failure criterion of soil through shear strength test is possible to evaluate…

A: To determine normal and shear stress at failure tria axial test is conducted, apart from this direct…

Concept explainers

Test for Determination of Shear Strength

The term shear strength is often associated with the soil. Shear strength is defined as the resistance to the deformation of soil particles due to the continuous action of shear stress. In short, shear strength is the maximum shear stress that a soil can sustain.

Question

The three principal modes of soil failure, established by the patterns of the shearing zones. Where does these modes are applicable in which soils type?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Test for determination of shear strength

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In AASHTO, which group are the following soils likely to fall into? a. A well graded gravel with approximately 10% fines. b. A well graded sand with approximately 10% fines. c. A uniform fine sand. d. A high plastic clay.
How are soils classified on the basis of shear strength? Draw the Mohr-Coulomb strength envelope and present the shear strength equation for each soil type.
What are the most widely used laboratory tests for studying the shear strength of different soils?
State an equation for consolidation settlement of a normally consolidated soil?
How does the understanding of the shearing strength of cohesive and cohesionless soils can be obtained by reference to the results from triaxial or direct shear tests?
Describe why effective stress is important when evaluating soil behavior. Please provide at least one example.
What is composition of ‘fines’ in slit categories of soil?
How to determine the modulus of sub-grade reaction (K) of the sub-grade soil ?
What relationship exists between permeability and void ratio for given soil? Explain.
Discuss Drilling Techniques in Competent Soils
Given that the hydrometer analysis test is based on stoke’s law, what is an inherent error of the method considering most of the soils tested hav a significant clay content ?
1) What are the two primary soil types in geotechnical engineering? Also, what are intermediate soils and how does the presence of fines influence soil behavior? Lastly, what happens when a soil is unsaturated and how does this impact behavior?