Give me right solution with clear calculations The three-reservoir system is shown below:AA2B13CThe elevation of Reservoir at A is 140m and at Cis 50m. The flow rate at Pipe 1 from Reservoir A is 2 m?/s. All pipes have a length of 500 meters, friction factor f = 0.02. and sizes namely:Pipe Diameter 1 (mm) = 600mmPipe Diameter 2 (mm) = 500mmPipe Diameter 3 (mm) = 500mmDetermine the flowrate at Pipe 2 in Liters per second.

Answered: Image /qna-images/answer/73c1c6ce-ba22-417e-a11e-445acb51093a.jpg

Answered: The three-reservoir system is shown…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the elevation of the upstream reservoir (A) in Figure P4.1.2 if the downstream reservoir(B) is at 750m, the flow rate ((water at 20 ℃) through the smooth concrete pipeline is ,1.2m^3/secgiven the following: pipes 1 and 2: 100m long (D=0.5m) valves 1–2: fully open globe valve expansion 2–3: D=0.5m to 1.0m pipe 3: 100m long (D=1.0m) pipe 5: 50m long (D=0.5m) pipe 6: 50m long (D=0.5m) confusor 4: loss coefficient of 0.3 bend 5–6: loss coefficient of 0.2
Two reservoirs are connected by three pipes. laid in parallel. The pipes diameters are respectively 10cm, 20cm and 30cm and they are of the some length. If discharge through 10cm pipe is 0.1 m3/s, calculate the discharge through the larger pipes. Assume the friction coefficient ‘f’ to be same for the pipes.
Two pipes are connected in parallel between two reservoirs: L1= 2600 m, D1 = 1.3 m, C1 = 90; L2 = 2400 m, D2 = 0.9 m, C2 = 100. For a difference in elevation of 3.8 m, determine the total flow (i.e. total Q) of the water. [Answer in units of m3/s]
Water flows from left to the right reservoir at a rate of 16 ft3/s (cfs). The head loss can be calculated as hL = 0.02(L/D)(V 2/2g), where L is the length of a pipe and D is the diameter. Determine the water surface elevation of the left reservoir.
Two water reservoirs of height h1 = 60 m and h2 = 30 m are connected by a pipe that is 0.35 m in diameter. The exit of the pipe is submerged at a distance of 8 m from the (2nd) reservoir surface. a. Provide a diagram b. Determine the flow rate through the pipe if the pipe is 80 m long and the (Fanning) friction factor f' = 0.004. The pipe inlet is set flush with the wall. c. If the relative roughness ε/D = 0.004, determine the friction factor and flow rate.
A new 45 cm cast-iron pipe 600 m long carries 260 litres/s from reservoir A, discharging into two new cast-iron pipes each 500 m long. One pipe is 30 cm in diameter and leads to reservoir B, in which the water surface is 5 m lower than in A. If the water surface in C is 7 m lower than that at A, determine the diameter of the pipe leading to C. Use n 0.011.
A 170-m long pipeline, composed of two pipes connected in series, discharges freely at a point 40 m below the water level at intake. The pipe projects into the reservoir. The first 100 m is 25 cm in diameter, and the remaining 70 m is 15 cm in diameter. Assuming that f=0.05 for both pipes, (a) find the rate of flow. If the junction of the two sizes of pipe is 25 m below the intake water-surface level, find the pressure head just above C and just below C, where C denotes the point of junction. Assume a sudden contraction at C. Use k=0.8 for entrance, 0.24 for sudden contraction and 1.0 for exit. I will downvote the incorrect solution
A reservoir A, the free water surface of which is at an elevation of 275 m, supplies water to reservoirs B and C with water surfaces at 180 m and 150 m elevation respectively. From A to junction D there is a common pipe 300 mm diameter and 16 km long. The pipe from D to B is 200 mm diameter and 9.5 km long while that from D to C is 150 mm diameter and 8 km long. Neglect losses other than pipe friction and taking f = 0.01 for all pipes. A. Calculate the rates of ﬂow at A in (m³/s) B. Calculate the rates of ﬂow at B in (m³/s) C. Calculate the rates of ﬂow at C in (m³/s)
Two reservoirs are connected by a pipeline consisting of pipe 1, pipe 2, pipe 3connected in series with length of 170 m, 300 m, 210 m respectively. Thedifferent in water surface levels in two reservoirs is 12 m. The friction coefficientfor pipe 1, pipe 2 and pipe 3 are 0.0052, 0.005 and 0.0048 respectively. Based onTable 2 and the setting given, determine the flowrate of the flow if the entranceloss coefficient is 0.25 considering :(i) minor losses; and(ii) neglecting minor losses pipe 1 =230(mm) Pipe 2 =330(mm) Pipe 3 = 430(mm)
Three reservoirs A, B and C whose water surface elevations are 60ft, 50ft and 32 ft respectively, are interconnected by a pipe system with a common junction at elevation 35ft. All pipes have a frictional factor of 0.020 and are as described as follows 1. Illustrate the problem 2. What is the direction of flow into reservoir B? 3. Determine the flow from reservoir B in ft^3/s. Indicate if it is Toward or away from junction D. 4. Determine the flow from reservoir C in ft^3/s. Indicate if it is Toward or away from junction D.
Three reservoirs A, B, and C is connected respectively with pipes 1, 2, and 3 joining at a common joint P whose elevation is 366m. Reservoir A is at elevation 933 m and reservoir B is at elevation 844 m. A pressure gage at junction P reads 4950 kPa. What is (a) the flow in pipe 1 in m³/s, (b) the flow in pipe 3 in lit/s, and (c) the elevation of reservoir C in meters
A pipe of length L = 500 m, diameter D = 300 mm and absolute roughness k = 0.02 mm transports a flow Q = 456 m3/h. Using the Darcy-Weisbach formula determine the hydraulic gradient and headloss through the pipe. The water temperature may be assumed to be 20° C.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS