The tip of a massless clamped-free beam connected to mass m = 2 kg by a spring with stiffness k = 4000 N/m. The mass is excited by a force 10 cos(49t) N. The beam is madeof a solid piece of steel with Young's Modulus of E = 200 GPa, second moment of area I = 270000 mm² and length L = 3 m. Neglecting the damping, the amplitude of themass matt = 1s-13.36 mm-5.40 mm12.63 mm1.67 mm-16.10 mmmasslesskE,I,Lmx(t)Fo cos(wt)

The mass of the block, The stiffness of the spring, The mass is excited by the force, The Young's…

Answered: The tip of a massless clamped-free beam…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A body of mass 100 kKg is suspended by a spring of stifness of 30KN/m and a dashpot of damping constant 1000 N.s/m. Vibration is excited by harmonic force ft)=80 cos (67tt) 1- Write the equation of motion of the system using Lagrange's equation. 2- Find the natural frequency and the driving frequency. 3- Write the complete solution of the vibrating system.
A block-spring system has a maximum restoring force Fmax = 0.1 N. If the amplitude of the motion is A = 0.01 m and the mass of the block is m = 100 g then the angular frequency w is equal to
A 65 kg painted sewing machine has an imbalance value of 0.15 kgm in rotation. The machine operates at 125 Hz and is located on the ground with a spring coefficient of 2 x 106 N / m and a dimensionless attenuation coefficient of 0.12. Find the uniform regime amplitude of the machine.
1)A 10 kg body suspended from the end of a vertical spring of negligible mass stretches it 10 cm. Assume that the body is pulled down initially to 5 cm and then released. If the damping force at any instant is 80 times its velocity at that instant. i)Calculate the amplitude of the motion. Options: a)0.0546 e–4t b)0.546 e–4t c)5.46 e–4t d)0.00546 e–4t ii)Calculate the Period of the motion. iii)Calculate the Frequency of the motion. "This question is not incomplete sir."
An elastic bar with flexural rigidity EI has a mass m at one end and pivots above the other in a frictionless bearing. A torsional spring with a modulus K supports the bar and mass in a horizontal position. Determine an equation for the calculations of the natural frequencies of the system.
1. Explain_why_the_natural_frequency_measurements_should_better_reflect_the_system’s_true_undamped natural_frequency_(and_therefore_correlate_better_with_calculated_values)_than_the_frequency_of_oscillation measurements. 2. For_a Linear Spring-Mass System, Torsional Spring-Mass System, and Simple Pendulum System: identify_the_necessary_measurements_required_to_identify_the_natural_frequency_and the damping_ratio_for_the_linear_SMD_and_the_simple_pendulum.
Determine the steady-state amplitude of the mass center of the bar of Fig P6.3 when its right end is subject to a moment M=4000son105t N.m.
A machine weighing 10kN is supported on its foundation by spring mounting. the piston of the machine moves up and down with a harmonic frequency 10 cycles per second. The piston has a weight of 500N and total stroke of 500mm. Determine the maximum force transmitted to the foundation if the total spring stiffness k = 5N/mm. Ignore damping.
A precision grinding machine is supported on an isolator that has a stiffness of 3 MN/m and a viscous damping constant of 3 kN-s/m. The floor on which the machine is mounted is subjected to a harmonic disturbance due to the operation of an unbalanced engine in the vicinity of the grinding machine. Find the maximum acceptable displacement amplitude of the floor if the resulting amplitude of vibration of the grinding wheel is to be restricted to 4*10^(-6)m. Assume that the grinding machine and the wheel are a rigid body of weight 6000 N. Use omega=100*Pi (previous answer to the same problem just different numbers)
An air compressor, weighing 100 kg, is mounted on an elastic foundation. I knowhas observed that when a harmonic force of 150 N amplitude is applied to the compressor, theMaximum steady state displacement is 6.2mm and occurs at a frequency of 320rpm.Determine: a) the equivalent stiffness, b) the damping constant "C" of the foundation andc) The force transmitted to the foundation. d) Illustrate using graphics
spring-mass system consists of a mass weighing 100 N and a spring with a stiffness of 2000 N/m. The mass is subjected to a resonance by a harmonic force F(t) = 25 cos ?t N. Find the amplitude of the force motion at the end of a) ¼ cycle, b) 2 ½ cycles, and c) 5 ¾ cycles.
An industrial sewing machine of 65 kg has an unbalance value of 0.15 kgm per rotation. The machine operates at 125 Hz and is located on the ground with a spring coefficient of 2 x 106N / m and a dimensionless damping coefficient of 0.12. Find the uniform regime amplitude of the machine.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS