The torque (C) to be transmitted by a drive at the welds is 650 Nm. Knowing that the diameter of the shaft is 40 mm and the constraint of allowable shear in the welded joint is 55 MPa. a) calculate the tangential force b) calculate the thickness of the weld.

Q: For the built-up section shown, determine the following: a. Centroid of the Area, b. Moment of…

A: Given:

Q: From the given figure below. Using Ranking Theory, the unit weight of concrete of gravity dam is 24…

A: Given:- The unit weight of the concrete = 24 kN/m3  The coefficient of friction between the concrete…

Q: A liquid flows through a pipe with a diameter of 10cm at a velocity of 9cm/s. If the diameter of the…

A: Continuity equation: The continuity equation states that the volume of the fluid entering per unit…

Q: What is the equivalent passive soil force (per lineal foot of wall) on the retaining wall?

A: Answer  We know that passive soil pressure is given by Pp = kp*σv' kp=1+sinϕ1-sinϕ kp=1+sin321-sin32…

Q: Direct runoff from a flood over a basin of area 50 ha was observed as 25000 m³ during a storm. The…

A:

Q: Determine the dimensions of the most economical trapezoidal earth lined channel (Manning's n=0.020)…

A: Given Data  Manninig constant (n) = 0.02  Discharge (Q) = 14 m3/sec  Bed slope (S) = 4 in 1000…

Q: A cement concrete pavement of a certain thickness laid over a sub grade has a radius of relative…

A:

Q: Calculate the coordinates of the polygon

A: Data given Find : coordinates of the polygon

Q: A soil sample has a bulk weight of 19.8 kN/m³ at a water content of 20%. Assume G₁ = 2.7 and…

A: The bulk unit weight, γt = 19.8 kNm3 Water content, w = 0.2 The specific gravity, GS = 2.7 To…

Q: Prob. 4-162 1 m W1 60 kN 80 KN -2.5 m- -3.5 m 50 kN 1 m W2

A: "Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: DISCUSS WHAT ARE THE ADVANTAGES OF TOP-DOWN PLANNING OVER BEGINNING-TO-END PLANNING ?

A: Top-down planning and beginning-to-end planning are two distinct approaches to project…

Q: A shear vane of 7 cm diameter and 11.0 cm length was used to measure the shear strength of a soft…

A: Given that :- diameter = d = 7 cm length = H = 11.0 cm Torque = T  = 700 kg-cm Find the shear…

Q: Q.1) Three forces and a couple moment are applied to an angle bracket as shown. The 50 lb force acts…

A:

Q: Given the two orthogonal projections of the object (top view and front view), identify the third…

A:

Q: Given: H = 52 ft, 80 h₁ = 47 ft, h₂= 50. 75 ft, discharge q under steady condition ft3/min, r = 10…

A: Unconfirmed aquifer with drawdown , radius information have been given and it has been asked to…

Q: Complete the table below with the correct values in two decimal places, but "v" must be in five…

A:

Q: Soil is to be excavated from a borrow pit which has a density of 1.75 gm/cc and water content of…

A:

Q: 1 - For the stress components acting on the material element shown below, calculate the principal…

A:

Q: (ii) The treated effluent containing grit particles from the above (i) activated sludge. system is…

A: Given, Settling velocity (V) = 2 m/s Dynamic viscosity (μ) = 0.001 kgm/s Radius (r) = 2 mm or 0.002…

Q: 4. A curve formed by a Back Tangent with a bearing of N 30° W and a Forward Tangent with a bearing…

A: Highway Curve: A highway curve is a curve that is formed by connecting two straight lines on a…

Q: A. Assume g = 30.50 ft/s² and V = 6ft³. a b C d e f v (m³/kg) 0.01500 p (kg/m³) 1700 7 (kN/m³) 9 m…

A:

Q: An ordinary mild steel bar has been prestressed to a working stress of 200 MPa. If the Young's…

A: Given- Initial prestress=200 MPa, Shrinkage strain = 8×10-4 E=200 GPa,

Q: Which

A: Dividing walls partition space in a room or a dwelling into separate spaces of other purposes.…

Q: What is the efficiency of joint when strength of bolt per pitch length is 60 KN and strength of…

A: Given: Strength of bolt per pitch length = 60 kN. Strength of plate per pitch length = 150 kN.

Q: Circular precast concrete piles with 60 cm in diameter will be driven to a tip penetration of 30 m.…

A: Circular precast concrete piles with 60 cm in diameter will be driven to a tip penetration of 30 m.…

Q: WRITE THE SHEAR AND MOMENT EQUATIONS BETWEEN CHANGE OF LOOD POINTS IN THE GIVEN BEAMS LOADED AS…

A:

Q: Replace the three forces acting on the rectangular solid with a wrench. Specify the magnitude of the…

A: Here, it is asked to replace three forces of Magnitude 10 n, 50N, and 15N with Magnitude of moment,…

Q: 1.14. Estimate the water lost because of a 1.0-mm-diameter hole in a 150-mm-diameter water main…

A: Given, Pipe diameter, D = 150 mm or 0.15 m Hole diameter, d = 1 mm or 0.001 m  Manning roughness…

Q: The duty of a crop is 432 hectares per cumec and the base period of the crop is 100 days. The delta…

A: Given: The duty of a crop, D = 432 Hectares per cumec. The base period of the crop, B = 100 days.

Q: Calculate the coordinates of the polygon

A: Data given Find : Coordinates of the polygon

Q: What are the types of loads on structures? (StructuralTheory in the Philippines)

A: For a structure to be design, the various forces are needs to be consider which are acting on the…

Q: Discuss why the inclusion  of subcontractor and other stakeholders a key part of planning process?

A: When a project meets or surpasses stakeholder expectations and accomplishes its goals, it is…

Q: A 100'x50' mat foundation (also called slab-on-grade) will be placed at the site shown in Figure 1.…

A: Given, Cc = 0.5 Cs = 0.1  σp = 1000 psf

Q: what are the pros and cons and which one is better for a parking lot: porous asphalt vs pervious…

A: What are the pros and cons and which one is better for a parking lot: porous asphalt vs pervious…

Q: What is length of transition curve for a B.G. curve of three degrees, having a cant of 10 cm. The…

A:

Q: Suppose the surface downward PAR is measured at 32.0 Watts/m2 at the ocean surface.  Assuming an…

A: Given data: Surface PAR measured, PAR(0)=32.0 watts/m2 Extinction coefficient, k=0.09 * Chl0.4 [m-1]…

Q: b.) What is the specific gravity of the gage fluid if h₂ = 0.5 m and pA - PB = 2.9 kPa 0.5 Flow n.…

A:

Q: Problem 6: Inputs: ● ● ● a = 6 ft b = 3 ft h = 4 ft w = 150 lb/ft Determine the reactions at A and…

A:

Q: Part 2: A girder shown below in figure 1 is subject to the following concurrent forces acting at…

A:

Q: your answer to the nearest whole number. Use 9.8 m/s² for the acceleration due to gravi N d }h water…

A:

Q: Q.2) A rigid pipe is acted on by three forces and a couple moment as shown. Replace the force and…

A:

Q: A high-strength steel bar used in a large crane has diameter d = 2.50 in. (see figure). The steel…

A:

Q: For the truss shown in the figure below, assume that the loads are being transmitted to the bottom…

A: Solution  ILD for member DI  Pass a section through member DI as shown below When the Unit load is…

Q: The A-36 steel column is encased in high-strength concrete as shown. If an axial force of 60 kip is…

A:

Q: SITUATION 13: Determine the reactions at the supports for the truss shown: 75 KN 150 kN 150 125 100…

A:

Q: Provide an example of hammock activity for the building project,together with predecessor and…

A: An activity that spans two points in a project timeline is referred to as a hammock activity in…

Q: Calculate the torque which a shaft of 3 cm diameter can safely transmit, if the shear stress is 48…

A: Given- Shaft diameter=3 cmshear stress=48 N/cm2

Q: Use g = 9.807 m/s² = 32.17 ft/s² and ywater = 9790 N/m³ = 62.4 lb/ft³ FL A two-dimensional analysis…

A: Given, FL=fL,V,D,α,ρ,μ,c where, L=Length V=velocity D=Diameter α=angle of attack ρ=density…

Q: [0.0016 [o] = 0.0003 0 0.0003 0.0008 0 0 0 0.0004. a. Determine the strain matrix for this strain…

A: Data given Find:  (a) Determine the strain matrix for the given strain state if the x and y axes…

Q: What exactly is a mock-up report, and how exactly does a report generator do its tasks?

A: A mock-up report is a sample or prototype report that is created to provide a visual representation…

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).