Questions:1.The total resistance of a series circuit consisting of 4 resistors is 8002. The knownresistor values are: R1 = 1000: R2 = 2000; R3 = 3000. What is the value of R4?Show your work.If 200 volts is connected to the circuit in question 1, what is the current flowingthrough resistor 2? Show your work.2.3.Again referring to the circuit in question 1, what is the voltage measured across R3?Show your work.4.What was the most significant benefit you gained from this lab experiment?5.How long did it take you to complete this lab experiment?Page 17 of 180550 assign_ELTE108_LabVolt_03_2020-02-12_ACC.docx

Since we only answer one question at a time, we’ll answer the first question since the exact one…

Answered: The total resistance of a series…

The total resistance of a series circuit consisting of 4 resistors is 8000. The known resistor values are: R1 = 1000; R2 = 2000; R3 = 300n. What is the value of R4? Show your work.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Know how to design simple voltage-divider and currentdivider circuits 1. Find the value of R that will cause 4 A of current to flow through the80 Ω resistor in the circuit shown.2. How much power will the resistor R from part (a) need to dissipate?3. How much power will the current source generate for the value of Rfrom part (a)?
A node in the circuit which is considered to hsve zero potential. A circuit analysus wherein the unknowns to be computed are voltages or potential differences. A circuit analysis wherein the unknowns to be computed are loop or mesh currents.
Q) Since VDD=+15 V, VTH= +2 V and K= 100mA/V^2 in the circuit below, what is the ID current? (R value specified in resistors in the circuit is ohm expression) NOT : I found the value of the current Id and it was 16 m A , but it was not there in the options, so I want to know what the correct answer is, although the options contain the voltage and required in the current question. Is there an error, and if the error is present, I want to answer the question to know what is required. please
An Engineer is tasked with implementing a lighting circuit with a 24 V battery. Part of the task included making sure power was conserved, e.g., ensuring the light stays off during daytime. The engineer selects a generic phototransistor to detect enough ambient light when present. The circuit below contains two transistors in series Q1, & Q2. This means that for the 35-Watt lamp (load) to work both transistors must be “ON” (or conducting), else the lamp is “OFF” (no current flows). Transistor Q1 is turned on by actuating the switch “SW1”. Transistor Q2 is turned on by the phototransistor Q4. The circuit is powered by a 24V Battery. Figure 1 shows the control circuit schematic and the simplified (equivalent) logic gate version of the circuit. (Hint: calculate your answer using Ohms law.)
Using the following values for the circuit in the figure, find what is required in the questions? For the circuit in the figure, find the ones requested in the questions by using the following values? VDD= 30 V, IDSS=8 mA, VP=-6V, R1=110 MΩ, R2=18 MΩ RD=1.9 kΩ, RS=9.12 kΩ VD=? VS=? VDS=?
Derive the gain of ?i /?o for the circuit of figure 3
For the circuit in the figure, find the ones requested in the questions by using the following values? VDD= 30 V, IDSS=8 mA, VP=-6V, R1=110 MΩ, R2=18 MΩ RD=1.9 kΩ, RS=3,68 kΩ VG=? VGS=? ID=? VD=? VS=? VDS=?
Node A What is the Voltage at Node A, VA Node C What is the Voltage at Node C, VC? Node B What is the Voltage at Node B, VB? Solve for Voltages V1, V2, and V3 What is the calculated voltage V1 in Volts (tenth-place degree of accuracy)? What is the calculated voltage V2 in Volts (tenth-place degree of accuracy)? What is the calculated voltage V3 in Volts(tenth-place degree of accuracy)? Solve for Current I3 What is the calculated current I3 in Amps (tenth-place degree of accuracy)?
Electrical Engineering 1. What voltage(s) should you provide when you power the Arduino through the barrel jack? How much current can be made available to the Arduino through this port? Does this port have any protection on it? 2. When you are powering the board using the barrel jack, what does the Vin pin do? 3. When you are powering the board using one of the ports mentioned above, how much current can you draw from the 5V pin? What about the 3.3V pin? What about a regular I/O (digital or analog) pin? 4. What voltage(s) should you provide when you power the Arduino through the Vin pin? How much current can be made available to the Arduino through this pin? Does this port have any protection on it? 5. What voltage(s) should you provide when you power the Arduino through the 5V pin? How much current can be made available to the Arduino through this pin? Does this port have any protection on it? 6. How much power does a normal 9V battery contain? How long could you run an Arduino board…
What are the values of Av, Rin, and Rout if the 2-kΩ source resistor is changed to 5kΩ as shown?
(a) Determine IC and VCE for the circuit (a) given below.(b) Change β to 120 (50% increase), and determine the new values of IC and VCE for the circuit of Figure (a)(c) Determine the magnitude of the percent change in IC and VCE using the following equations:(d) Determine IC and VCE for the network of Figure (b).(e) Change β to 180 and determine the new value of IC and VCE for the network of Figure (b)(f) Determine the magnitude of the percent change in IC and VCE using the above equations. (g) In each of the above, the magnitude of β was increased 50%. Compare the percent change in IC and VCE for each configuration, and comment on which seems to be less sensitive to changes in β.
Taking into account the scheme of the Voltage divider (voltage divider) shown in the following image, Design the circuit by calculating its resistances (R1 and R2) to obtain an output voltage ???? of 5V dc maximum, taking into account that the input voltage ??? is 30V dc. (Use values greater than or equal to 1KΩ). - Calculate the voltage drops in each resistance - Measure the current that passes through the voltage divider circuit