The transformer output voltage is V 2=8968.320°v. Reg = 12, Xeg = 100 and its core losses =166.3 W, Find the transformer efficiency (in percent %) of the above figure if its output power is 804.9 kW at load power factor o.7 lagging. (Do NOT write the units or letters (or%) in the answer space)

The transformer output voltage is V 2=8968.320°v. Reg = 12, Xeg = 100 and its core losses =166.3 W, Find the transformer efficiency (in percent %) of the above figure if its output power is 804.9 kW at load power factor o.7 lagging. (Do NOT write the units or letters (or%) in the answer space)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.7P: Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer...

See similar textbooks

Related questions

Q: A Transformer with 10:1 ratio and rated at 50-kVA, 2400/240-V, 50-Hz is used to step down the…

Q: A single-phase, dry-type, general-purpose industrial distribution A transformer has the…

A: Given data, P=50 kVAf=60 HzVH=480 VVL=120 VZimpedance=3.80+j4.43 Ω%R=3.80 Ω%X=4.43 ΩPi=105 W

Q: A single phase transformer is given: SN= = 100 kVA, V₁10 kV t = 25. The short circuit parameters…

Q: A 1-phase transformer, 15 kVA, 660/250V, 50HZ, Reg1= 2.78790 and Xegi = 5.57572. %3D the secondary…

A: According to the question, we have to calculate the value of regulation up at full load and power…

Q: A 2,300/240-V, 60-Hz, 4.6-kVA transformer isdesigned to have an induced emf of 2.5 V/turn.Assuming…

A: The given transformer is a step-up transformer. a. The numbers of high-side turns are calculated as…

Q: A 4 MVA, 66/13.2 Kv, 50 Hz. Delta star connected Three phase transformer has a primary resistance…

A: The current flowing in a circuit causes a voltage drop. The voltage drop should be within allowable…

Q: QS A 20KUA , 200/Soo usit single phax step-uptransformer Ras: primary resistanue 3.0.02 23 secondany…

A: The data for the question are: 20kVA, 200/500V,R1=0.02Ω,R2=0.04Ω,Ro=1000Ω,Xo=750Ω The magnetizing…

Q: Given a transformer (single-phase, 10kVA, 2400/240V, 60Hz) Z1 = 5.2 + j12.5 ohms; Z2 = 0.06 + j0.12…

A: In this question we need to find a load voltage of transformer for given condition.

Q: Assume that there are two primary feeders supplied by a transformer T1. One of the feeders supplies…

A: We know, Diversity Factor=Maximum noncoincident demandmaximum diversified demandThe maximum…

Q: The open circuit test in a 100 kVA, 2000/200 V, 50 Hz, single phase transformer gives 200 V, 90 A, 5…

Q: . A 10 kVA, single-phase, 2400-V:120-V, 60 Hz transformer has an equivalent impedance referred to LV…

A: Given a single phase transformer with the following values 10 KVA ,2400v/120v ,60 Hz Core loss…

Q: A single-phase l0-kVA, 480/1120 -V transformer is to be used as an auto transformer tying a 600V…

Q: A 400-k VA, 2300 230, 60-hz transformer supplies a 0.8 lagging power-factor load whose KVA Is…

A: The efficiency of the transformer is given by the relation, Where, x = percent rated load…

Q: Data from short-circuit and open-circuit tests of a 25-kVA, 6900-230 V, 60 Hz transformer are given…

Q: Question 1 An ideal two winding transformer with a rectangular oross-sectional area of 60cm by 20cm…

Q: (b) A 50-kVA, 2600/1300-V, single-phase transformer has a core loss of 780 W. The transformer has a…

Q: 2) 50 kVA, 2300 V / 230 V transformer draws 750 W power and 0.5 A current at rated idle primary…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: A 15-kVA 8000/230-V distribution transformer has an impedance referred to the prima of 80+ j3000.…

A: a. The turns ratio of the transformer is determined as a=8000230=34.78 The load impedance referred…

Q: 14. In a 50-kVA, 11-kV/400-V, single-phase transformer, the iron and copper losses are 500 W and 600…

A: Given data, KVA rating S = 50 KVA Voltage rating 11 KV / 400 V Iron loss Pi=500 W Copper loss,…

Q: A 1000-VA, 230/115-V traformer has been tested to determine its equivalent circuit. The results are…

Q: A single-phase transformer, with primary turns of 500, is delivering full-load of 80 kW at a lagging…

A: output power Po= 80 KW N1= 500 I2= 227 A ; cos ∅ =0.8 Po= 80 x 103 V2I2 cos ∅ = 80 x 103…

Q: Open-circuit test Short-circuit test Voc = 480 V Vsc = 10.0 V loc = 0.41 A Isc = 10.6 A %3D Poc = 38…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: (b) A transformer takes a current of 0.7A, when its primary is connected to a 225V, 50Hz supply, the…

A: Transformer open circuit test. No load current 0.7A Primary voltage 225V Power =70W

Q: A 2.4-kVA, 2400/240-V, 50-Hz, step-down transformer has the following parameters: R, = 1.5 a, X, =…

Q: A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal…

A: Given Data: KVA = 10 Voltage = 480 V Z=10 Ohm and angle =30 R=20 Ohm and X=60 Ohm

Q: 1. Why is it not adjustable to carry or the same experiment for large transformers? 2. What method…

A: 1) Large transformers need large supply voltages which is difficult to achieve in an experimental…

Q: A 40 kVA, 6,600/250V, 50 Hz transformer is having total reactance of 35 ohms when referred to…

A: Given Data: Rating = 40 kVA R1 = 10 ohm R2 = 0.2 ohm E1 = 6600 V E2 = 250 V

Q: A 1000-VA, 230/115-V traformer has been tested to determine its equivalent circuit. The results ar…

A: A transformer is an electrical machine which is used in AC circuit to either step up or step down…

Q: A 5kVA, 4160/240V, 50-Hz distribution transformer is used to feed a single-phase load with a P.F of…

A: i) Let the resistance and reactance of the transformer on the low voltage side be RL and XL…

Q: A transformer of 100MVA, 60Hz, 138/69 kV, works as step down, has the following parameters: r1 =…

Q: A 37.5-kVA, 6900-230-V, 60-Hz, single-phase transformer is operating in the step-down mode at rated…

A: a) Given data Apparent power is S = 37.5 KVA Low side voltage is VLS = 230 V Frequency is f = 60 Hz…

Q: A 400-turns auto transformer, operating in the step-down mode with 25 percent tap supplies a 4.8…

Q: A 30-kVA, 8000/230-V distribution transformer has impedance referred to the primary of 20 + j100 N.…

A: We are authorized to answer one part of the question at a time since you have not mentioned which…

Q: A 230/400 V single-phase transformer absorbs 35 W when its primary winding is connected to a 230 V,…

Q: transformer with a 10:1 ratio and rated at 60kVA, 2200/220V, 60Hz is used to step down the voltage…

Q: Q2: A 4000/400 V, 10 kVA transformer has the following constants: Primary and secondary winding…

Q: Example 10. A 3300/230 V, 50-kVA, transformer is found to have impedance of 4% and a Cu loss of 1.8%…

A: In this question we will find percentage reactance and ohmic value of resistance , reactance and…

Q: A 50-kVA, 2600/1300-V, single-phase transformer has a core loss of 780 W. The transformer has a high…

Q: (a) A 220 / 400V, 14KVA, 50HZ single phase transformer has at full load, a copper load of 140W. If…

Q: Q.29: For the ideal transformer circuit shown, find the 452 average power delivered to (1Q)…

A: for the ideal transformer circuit shown find the average power delivered to 1ohm resistor

Q: The primary and secondary windings of a 500-kVA, 11-kV/415-V, single-phase transformer have…

Q: Question 1 An ideal two winding transformer with a rectangular cross-sectional area of 60cm by 20cm…

Q: The label values of the single-phase transformer whose electrical equivalent circuit is given…

Q: A 5000-KVA 230/13.8-kV single-phase power transformer has a per-unit resistance of 1 percent and a…

A: In this question we need to find a equivalent circuit referred to LV side of transformer , voltage…

Q: carrying? Ans. 10 45 percent 10.44 A 100-KVA transformer is at 80 percent of rated load at power…

Q: A 15-kVA 8000/230-V distribution transformer has an impedance referred to the primary of 80 + j3002.…

A: Part (a): The turn ratio of the transformer is determined as: a=8000 V230 V=34.78 The load impedance…

Q: A 240-kVA, 480/4800-V, step-up transformer has the following constants: Rs = 2.5 Ω, Xs = j5.75 Ω, Rp…

A: Given step up Transformer with240 KVA, 480/4800 vRs=2.5 Ω,Xs=j5.75 ΩRp=25 mΩ,Xp=j57.5 ΩThe core…

Q: A 15-kVA, 2300/230- Question-2 !* V transformer has the following resistances and leakage…

A: As per the guidelines of Bartley we supposed to answer first three subpart only

Q: Primary side-reduced equivalent circuit parameters of a 25 KVA, 50 Hz, 4000/400 Volt transformer R1…

A: Given: A 25KVA, 50Hz, 4000/400V transformer in which…

Q: 302 j722 םרהj 302 The label values of the single-phase transformer whose electrical equivalent…

A: Given: A 20 KVA, 15400 V/240 V, 50 Hz, single-phase transformer has the following equivalent…

Concept explainers

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.

Question

The transformer output voltage is V 2=8968.320°v. Reg = 12, Xeg = 100 and its core losses =166.3 W, Find the transformer efficiency (in
percent %) of the above figure if its output power is 804.9 kW at load power factor o.7 lagging. (Do NOT write the units or letters (or%) in the answer
space)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240-volt secondary winding, absorbs 60 kVA at 0.8 power factor lagging and is at 230 volts. Assuming an ideal transformer, calculate the following: (a) primary voltage, (b) load impedance, (c) load impedance referred to the primary, and (d) the real and reactive power supplied to the primary winding.
Consider Figure 3.25 of the text for a transformer with off-nominal turns ratio. (i) The per-unit equivalent circuit shown in part (c) contains an ideal transformer which cannot be accommodated by some computer programs. (a) True (b) False (ii) In the - circuit representation for real c in part (d), the admittance parameters Y11 and Y12 would be unequal. (a) True (b) False (iii) For complex c, can the admittance parameters be synthesized with a passive RLC circuit? (a) Yes (b) No
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.
An ideal transformer has no real or reactive power loss. (a) True (b) False
A single-phase 50-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer at the load end of a 2400-volt feeder whose series impedance is (1.0+j2.0) ohm. The equivalent series impedance of the transformer is (1.0+j2.5) ohms referred to the high-voltage (primary) side. The transformer is delivering rated load at a 0.8 power factor lagging and at a rated secondary voltage. Neglecting the transformer exciting current, determine (a) the voltage at the transformer primary terminals, (b) the voltage at the sending end of the feeder, and (c) the real and reactive power delivered to the sending end of the feeder.
A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
Consider Figure 3.4. For an ideal phase-shifting transformer, the imda nce is unchanged when it is referred from one side to the other. (a) True (b) False
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
A single-phase two-winding transformer rated 90MVA,80/120kV is to be connected as an autotransformer rated 80/200kV. Assume that the transformer is ideal. (a) Draw a schematic diagram of the ideal transformer connected as an autotransformer. showing the voltages, currents, and dot notation for polarity. (b) Determine the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of the kA rating is transferred by magnetic induction?