The two 500-lb forces are parallel to the y axis and the P force is parallel to the z axis. If the allowable shear stress is 8 ksi, calculate the smallest permissible diameter of the solid shaft AE. Use the Maximum Shear Stress failure theory.

The two 500-lb forces are parallel to the y axis and the P force is parallel to the z axis. If the allowable shear stress is 8 ksi, calculate the smallest permissible diameter of the solid shaft AE. Use the Maximum Shear Stress failure theory.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.9.4P: A circular pole is subjected to linearly varying distributed force with maximum intensity t0....

See similar textbooks

Related questions

Q: a) Determine the "torsional" shear stress (resulting from torque) at point A. (absolute value)

A: ζ =TJRζ = torsional shearT = torsionJ = Polar MOIR = maxiumum radius

Q: As shown below, a homogeneous 50-kg rigid block is suspended by the three springs whose lower ends…

A: Given Steel spring N = 24 turns Spring wire diameter = 10 mm Mean diameter = 100 mm Bronze N = 48…

Q: Determine the maximum shear stress in the solid shaft. The diameter of the shaft is 1 in. Assume the…

A: Given-Data:- Diameter of shaft=1inch No Friction is assumed To-Find:- Maximum Shear Stress

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A: Given data d=0.75 inP=52 kipsn=5 Here, d is the diameter and P is the load applied. Here, n is the…

Q: The shaft consists of a 3-in.-diameter aluminum segment that is rigidly joined to a 2-in.-diameter…

A: Given data: The diameter of the steel rod is dst=2 in The diameter of the aluminium rod is dal=3 in…

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

Q: The solid aluminum shaft ABCD carries the three torques shown. (a) Determine the smallest safe…

Q: Determine the torsion on the rigid supports and the maximum shearing stress developed in each…

Q: The solid shaft of radius r is subjected to a torque T. Determine the radius r of the inner core of…

A: given data as per the question The radius of the bar = r Torque subjected = T

Q: Q.1: Calculate the maximum shear stress developed in each segment when the torque T = 100 N.m. is…

Q: Q1: The C-shaped steel bar has cross section of a square of side 1.6 in. If the magnitude of…

A: given data force p= 2 kips dimension of cross section= 1.6 ×1.6 in^2 find the combined stress at…

Q: Q1- Prove that the shear stress of circular shaft under pure torsion is Tr Tmax Ip Ex

Q: The bearings at A and B exert only x and z components of force on the steel shaft. Determine the…

Q: The compound shaft made from the same material consisting of two segments AC and CB is firmly…

Q: Determine the required diameter of the pins at A and B to the nearest 116 in. if the allowable shear…

A: Given, Pin A is subjected to double shear and Pin B is subjected to single shear.

Q: Compute the outer and inner diameter of the hollow circular rod when it is subjected to an axial…

A: Given data as per question Axial pull = 350 KN Allowable stress = 125 N/mm2 Thickness of rod = 10 mm…

Q: The bar AB is supported by a frictionless inclined surface at A and a 7/8-in.-diameter pin at B that…

Q: The lever is held to the fixed shaft using a tapered pin AB, which has a mean diameter of 6 mm. If a…

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A: Given data: P=64 kips diameter of bolt (d)= 0.75 in.

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

Q: Q1- Prove that the shear stress of circular shaft under pure torsion is Tr %3D Tmax Ip

A: Given Circular shaft To find ζmaax=TrIP

Q: When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this…

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

Q: Determine the torque T that can be applied to the rectangular tube as shown in figure(5),if the…

A: To find: The torque T that can be applied to the rectangular tube. Given data: The average shear…

Q: Calculate: (a) the maximum torque that can be applied to the shaft. (b) the minimum diameter of the…

A: Given Dataσy=450MPaE=205GPaτy=σy2=225MPar=45mm

Q: Determine the maximum shearing stress and elongation in a bronze helical spring composed of 20 turns…

Q: A simplified diagram of a racing cars suspension and wheel is used to design the bars and pins. The…

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

A: Given data Diameter of steel shaft = 30 mmAllowable shear stress = 120 MPaAngle of twist = 7°Shear…

Q: Q2) The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. If the…

A: Given data:- Internal radius, r1=25 mm Outer radius, r2=40 mm

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 15…

A: Given, d = 15 mmτmax = 120 MPa = 120 N/mm2θmax = 5° = 0.08727 radG = 80 GPa = 80,000 N/mm2l = 500 mm…

Q: The aluminum shaft, composed of three segments, is fastened to rigid supports at A and D. Calculate…

Q: The 5.7-in diameter steel shaft AB is attached into the rigid wall at C and supported by a smooth…

Q: The lap joint is fastened with four 3/4-in. diameter rivets. The working stresses are 14 ksi for the…

Q: The box beam is constructed from four boards that are fastened together using nails spaced along the…

A: Let us consider the crossection of the given beam:

Q: The solid and hollow shafts are each subjected to the torque T. In each case, sketch the shear…

A: The solid shaft is subjected to torque T in a clockwise direction. The shear stress is calculated…

Q: The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable…

A: given; diameter of steel(d1)=0.500inallowable shear stress of steel(τs)=13ksimaximum torque…

Q: The bar has a circular cross section with 1-in diameter. If the torque TO = 1000 in-lb, determine…

Q: 500kg-engine is hanged on hook shown below. Calculate normal stress on rod CD where it has a…

Q: Determine the required diameter of the pins at A and B if the allowable shear stress for the…

Q: The shaft is made from a solid steel section AB and a tubular portion made of steel and having a…

A: In this question we have to find angle of twist of C wrt A and max. shear stress and strain in brass…

Q: The stepped steel shaft carries the torque T. Determine the maximum allowable magnitude of T if the…

Q: The control arm is subjected to the loading show. The allowable shear stress for the steel pin is 8…

A: Given that the allowable shear stress in the pins 'A' and 'C' is: τall=8 ksi Let dA,dC be the…

Question

please explain it in detail

The two 500-lb forces are parallel to the y axis and the P force is parallel to the z axis. If the allowable
shear stress is 8 ksi, calculate the smallest permissible diameter of the solid shaft AE. Use the Maximum
Shear Stress failure theory.
500 lb
500 lb

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given Data

Free Body Diagram

Calculations

Calculations

Calculations

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Solve the preceding problem (W 250 × 44.8) if the resultant force P equals 110 kN and E = 200 GPa.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 30mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120MPa and it's angle of twist is limited to 7deg. Use G=83GPa for steel. -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.
The solid steel rod (1) has an allowable shear stress of 12 ksi. The brass tube (2) has an allowable shear stress of 5 ksi. The diameter of the rod is d1 = 0.625 in. The outside diameter of the tube is D2 = 1.625 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod.
The shaft assembly is made from a steel tube 1 in. in diameter, which is bonded to a solid brass core 0.5 in. in diameter. If a torque of 250 lb-ft is applied at its end, determine the maximum shear stress in psi experienced by the assembly. Take G for steel at 11.4x103 ksi and G brass at 5.2 x 103 ksi. complete soln.
Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 2.0 kN. The crankshaft dimensions are b1 = 90 mm, b2 = 120 mm, and b3 = 40 mm. The diameter of the upper shaft is d = 20 mm. Determine the normal stress at point B, which is located on the surface of the upper shaft at the y0 axis.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 20 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 8 kips, Q = 5 kips, R = 20 kips and S = 28 kips. Calculate F1, F2, F3 and..