Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 20 mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120 MPa and its angle of twist is limited to 7 deg. Use G=80 GPa for steel 300mm 500 mm

Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 20 mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120 MPa and its angle of twist is limited to 7 deg. Use G=80 GPa for steel 300mm 500 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.8.5P: A stepped shaft ACB having solid circular cross sections with two different diameters is held...

See similar textbooks

Related questions

Q: In the Figure 3, if m=15 kg and e=30°, then the weight component normal to the block is: * m Figure…

A: For solve this problem, we resolved weight of body which is the product of mass and acceleration due…

Q: The roof of a house consists of a 0.70-ft-thick concrete slab (k = 3 W/m · °C) that is 18 m wide and…

A: Given that, Thickness of concrete slab, t=0.70 ft,Thermal conductivity of the concrete, k=3…

Q: In the Figure 1, the relationships between vectors and internal angles can be represented as: Figure…

A: This can be explained using the sine rule.

Q: 0.5 and For the system shown, the spring constant k = 400 kN/m, damping coefficient zeta = mass m =…

Q: 9. The net work done per engine cycle in a 4-stroke diesel internal combustion engine (as in the…

A: (a) The indicated power of the engine is 74.8 kW. (b) The power dissipated due to frictional forces…

Q: 00000 Consider the following equation of motion, 1000# (t) +. cż (t) + 2000z (t) = 1008(t) N…

Q: A 125mm-diameter work-bar, 1200mm long is held between centers of an engine lathe. A 400mm portion…

Q: Find the maximum shear Shees 61=40 MP9 62=32 MPa.

A: Given data : The value of maximum principal stress σ1=40 MPa The value of minimum principal stress…

Q: A shaft is rotating at a uniform speed with four masses m1, m2, m3 and m4 of magnitudes 300 kg,…

Q: In the Figure 3, if the m=15 kg and 0=30°, then the weight component of the block parallel to the…

A: Given data : Mass of object m=15 kg Acceleration due to gravity g=9.81 m/s2 Angle θ=30∘

Q: The 20-lb disk rests on the 5-lb plate. A cord is wrapped around the periphery of the disk and…

A: Given Mass of disk, md = 20 lb Mass of plate, m = 5 lb Time, t = 1 sec…

Q: Q1: The shaft BC is hollow with inner and outer diameters of 100 mm and 120 mm respectively. Shaft…

Q: In a duct of uniform cross section only static pressure remain constant the total pressure decrease…

A: 1. First we will talk about static and dynamic pressure In bernoulli's equation you have two…

Q: H.W.2 /: Consider a 55cm long journal bearing that is lubricated with oil whose viscosity is 0.1…

Q: The 470-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

Q: Solve 5 problems (following the conditions stated below) involving the use of shear and moment…

Q: What is the flow rate of the oil (sg 0.73) in the pipe below based on the measurements in the…

A: Find the flow rate .

Q: The horizontal axis on a coordinate plane is called the _____________-axis

A: Define the coordinate plane.

Q: Consider an air-standard Otto cycle that has a compression ratio of 7.8 and a heat addition of 1250…

Q: Consider a compression-ignition engine with compression ratio of 16.5 and temperature at the…

Q: The rectilinear motion of a particle is governed by a = 12t – 6t². It starts from rest when t = 0.…

Q: b- What is the crystal structure of an iron carbon 1.2% alloy that has been cooled from temperatures…

A: First draw the iron iron carbide diagram

Q: According to the Figure 2, if P = 60 N and R = 100 N, then e should be: * Figure 2: R α 34.8° О…

A: Given: P = 60 N R = 100 N correct answer: (b) 36.8 deg

Q: In the Figure 1, the resultant R can be found by using the law of cosines as:

A: Given data : Force=P Force=Q Resultant=R To find ; Correct formula

Q: section shown in figure Question 2, determine the shear stress a. In the Web at point A b. and in…

Q: In graphical solution, the resultant of two vectors should be drawn from the starting point of the…

A: GIVEN DATA- A MCQ QUESTION GIVEN ABOUT VECTOR

Q: Fill in the blanks. A 5 Hp Carnot engine operates between temperature limits of 300°C and 50°C. Find…

A: Given data, For a Carnot engine whose capacity ( workdone) is 5 Hp ie. w= 5hp=3.7285kW T1= 300°C…

Q: PROBLEM 2 The elements of a floor jack are shown in the figure. If the hydraulic cylinder AB is…

A: According to the question: ∑Md=0 1.25EFcosα + 1.25EFsinα = 0 EF=0 BY equating the sum of forces in…

Q: F. What is the compression ratio?

A: Given: T3= 2500 deg F. T4= 886 deg F To find : Compression ratio

Q: (a) Describe THREE (3) distinguishing features between NC and CNC systems. (b) Define the following,…

Q: Consider a compression-ignition engine with compression ratio of 16.5 and temperature at the…

A: Given Data: Compression ratio, r=16.5

Q: Derive the shear and moment equations for segment AB of the beam shown. 2.1 kN/m A C B te2 m- 5 m

Q: Now consider two very similar semi trucks. One travels at 40 km/hr and another travels at 75 km/hr.…

A: -considering equal masses ( similar trucks)

Q: The assembly in Figure consists of a light rigid bar AB, pinned at 0, that is attached to the steel…

Q: 12-29. A particle is moving along a straight line such that when it is at the origin it has a…

Q: 1 Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid…

Q: The trigonometric functions ( sine, cosine, and tangent ) are applied in: * O Not right angle Right…

A: Correct answer: (b) Right angle

Q: left and right ends of a 2.0 kg block ely it rotates about the origin. If the block is 3 m in length…

Q: n the following information, determine the steer angle required to c ly state conditions around a…

Q: The static coefficient of friction is smaller than the kinetic coefficient of friction. True O False

A: The static friction comes into existence when surfaces in contact are stationary and acted upon by…

Q: A rotating viscometer consists of two concentric cylinders - an inner cylinder of radius Ri rotating…

A: The profile of velocity of fluid is always parabolic or 2nd order but if we reduce the gap between…

Q: is it possible to predict the metallic phases that may arise during the casting and solidification…

A: Solution: To Find: Is it possible to predict the metallic phases that may arise during the casting…

Q: To draw the vectors in graphical solution we need to specify first the scale of measurements. * O…

A: Correct answer: True

Q: After isentropic expansion, the temperature is 1900 K.Consider a compression-ignition engine with a…

Q: 3. The results of a simple calibration of pressure transducer and its specification are shown in…

A: Given: To Find:

Q: what is the value of maximum principal stress in the figure below?

A: Find the maximum principal stress .

Q: Methane is heated in a steady-flow process at approximately atmospheric pressure. 1000 kJ of heat is…

A: Entropy Change is process which measures the change of disorder or randomness in any thermodynamic…

Q: À 2-in sch40 pipe line carries water at 70°C. A sharp-edged orifice (1.077 inches in diameter)…

A: Given data, Diameter of the pipe, D = 2 in = 0.1667 ft Diameter of the orifice in first case, d1 =…

Q: A diesel power plant consumed 1 cubic ft of fuel with 30 API at 30 deg. C in 24 hrs. Calculate the…

Q: 3- Two cars muvng towards each other, separated by 150 km, If the first car has a speed of 60 m/s…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

PROBLEM 1
Two forces , each of magnitude P, are applied to the wrench.
The diameter of the steel shaft AB is 20 mm. Determine the
largest allowable value of P if the shear stress in the shaft is
not to exceed 120 MPa and its angle of twist is limited to 7
deg. Use G=80 GPa for steel
300 mm
s00 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
A circular steel tube with an outer diameter of 75 mm and inner diameter of 65 mm is subjected to torques 7"at its ends. Calculate the maximum permissible torque 7jliajl if the allowable normal strain is ea= 5 X 10"4 Assume that G = 15 GPa.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.