The two blocks used in a measuring device have negligible weight. The spring iscompressed 4 in. when in the position shown in (Figure 1). The end of the screw issmooth and the coefficient of static friction at all other points of contact is μ = 0.34.FigurePart APk = 20 lb/in.P= 34.6μA 3BDetermine the smallest axial force P which the adjustment screw must exert on B inorder to start the movement of B downward.Submit Previous Answers45°Express your answer to three significant figures and include the appropriateunits.▸ View Available Hint(s)lbA 60°1 of 1 >>?X Incorrect; Try Again; 2 attempts remaining

Answered: Image /qna-images/answer/0c63ca3a-825f-4603-a2f3-130e5caaa9c4.jpg

The two blocks used in a measuring device have negligible weight. The spring is compressed 4 in. when in the position shown in (Figure 1). The end of the screw is smooth and the coefficient of static friction at all other points of contact is , = 0.34. Figure ▼ Part A P k = 20 lb/in. P= 34.6 HA Determine the smallest axial force P which the adjustment screw must exert on B in order to start the movement of B downward. 45° Express your answer to three significant figures and include the appropriate units. ▸ View Available Hint(s) Submit Previous Answers A 60° lb 1 of 1 ? X Incorrect; Try Again; 2 attempts remaining

The two blocks used in a measuring device have negligible weight. The spring is compressed 4 in. when in the position shown in (Figure 1). The end of the screw is smooth and the coefficient of static friction at all other points of contact is , = 0.34. Figure ▼ Part A P k = 20 lb/in. P= 34.6 HA Determine the smallest axial force P which the adjustment screw must exert on B in order to start the movement of B downward. 45° Express your answer to three significant figures and include the appropriate units. ▸ View Available Hint(s) Submit Previous Answers A 60° lb 1 of 1 ? X Incorrect; Try Again; 2 attempts remaining

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.63P: The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The...

See similar textbooks

Similar questions

The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of static friction between each pad and the cylinder is 0.15. Find the smallest tension in the spring that would prevent the cylinder from rotating when the clockwise couple M=2200lbin. is applied. Neglect the weights of the members.
The single-plate clutch transmits the torque C from the input shaft on the left to the output shaft on the right. Compression springs between the clutch housing and the pressure plate provide the necessary pressure on the friction surface. The splines prevent the clutch plate from rotating relative to the output shaft. If Ri=4 in. and R0=9 in., determine the total force that must be applied to the pressure plate by the springs if the clutch is to transmit a torque of C=56lbft when it is new.
Determine the force P required to move the wedge to the right if the coefficient of static friction is 0.35 at all contact surface (Figure 3). The uniform cylinder weight, W is 20 kN, and the weight of the wedge may be neglected.
roll of paper has a uniform weight of 2kN and is suspended from the wire hanger so that it rests against the wall. If the hanger has a negligible weight and the bearing at O can be considered frictionless, determine the force P needed to start turning the roll if = 30°. The coefficient of static friction between the wall ܬܐ and the paper is µ = 0.3.
The homogenous 360 kg block rests against the vertical wall, for which the coefficiewnt of friction is 0.25. A force P is applied to the midpoint of the right face in the direction shown in thre figure. What range of values may P have without disturbing equilibrium. Give solution. (Ans. 5260 N < P < 7890 N)
The block brake consists of a pin-connected lever and friction block at B. The coefficient of static friction between the wheel and the lever is μs = 0.3, and a torque of 5 N ⋅m is applied to the wheel. Determine if the brake can hold the wheel stationary when the force applied to the lever is (a) P = 30 N, (b) P = 70 N Draw the free-body diagram of the lever.
The wheel is subjected to a torque of M = 90 N⋅m . The coefficient of kinetic friction between the band brake and the rim of the wheel is μk=0.3. (Figure 1) Determine the smallest horizontal force P that must be applied to the lever to stop the wheel.