The two-dimensional incompressible flow-field around a Rankine vortex of strength r and core size R,has only a circumferential component, v. The value of v is given as follows:Rгv(r)Trr< R27 R?v(r)r > R2rDetermine the vorticity of this flow-field and the pressure coefficient, Cp, and plot them as a function ofr/R. The non-dimensional pressure coefficient C, is defined below. Where is the pressure expected tobe minimum, and what is the value of the minimum C,? (Use polar coordinates)p - PooCpwhere p. is the pressure at infinity, and p is the density of the fluid. VR is the flow velocity at the outeredge of the vortex core (i.e. at r= R)

Answered: Image /qna-images/answer/ab485c70-4c05-449d-94df-045db3dc1fce.jpg

Answered: The two-dimensional incompressible…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

How might the remarkable three-dimensional Taylorinstability of Fig. 4.14 be predicted? Discuss a generalprocedure for examining the stability of a given flowpattern.
A tornado in atmospheric air is simulated by a CCW free vortex as a potential flow field. The velocity measured at r = 1 m from the center is 60 m/s. Determine the magnitude of dynamic pressure P at r = 10 m . (Use pi number = 3 , Air density = 1 .0 kg/m3 )ANSWER: P= 18 Pa
When a line source–sink pair with m= 2 m2/s is combinedwith a uniform stream, it forms a Rankine oval whose minimumdimension is 40 cm. If a = 15 cm, what are thestream velocity and the velocity at the shoulder? What isthe maximum dimension?
Consider a flow field represented by the stream functionψ=(4+1) x3y - (6+1) x2y2 + (4+1)xy3. Is this a possible two-dimensionalincompressible flow? Is the flow irrotational?Discuss the reasons against your findings.
Consider the flow field V = (ay+dx)i + (bx-dy)j + ck, where a(t), b(t), c(t), and d(t) are time dependent coefficients. Prove the density is constant following a fluid particle, then find the pressure gradient vector gradP, Γ for a circular contour of radius R in the x-y plane (centered on the origin) using a contour integral, and Γ by evaluating the Stokes theorem surface integral on the hemisphere of radius R above the x-y plane bounded by the contour.
Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2 (2116 lb/ft2), respectively. Consider a venturi with a small hole drilled in the side of the throat. Thishole is connected via a tube to a closed reservoir. The purpose of theventuri is to create a vacuum in the reservoir when the venturi is placed inan airstream. (The vacuum is defined as the pressure difference below theoutside ambient pressure.) The venturi has a throat-to-inlet area ratio of0.85. Calculate the maximum vacuum obtainable in the reservoir when theventuri is placed in an airstream of 90 m/s at standard sea level conditions.
Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2(2116 lb/ft2), respectively. Prove that the flow field specified is not incompressible;i.e., it is a compressible flow as stated without proof .
Consider a two-dimensional flow which varies in time and is defined by the velocity field, u = 1 and v = 2yt. Given that the density of the fluid does not vary spatially and changes only with time, what differential equa9on for the density, ⍴(t), must be satisfied for this scenario to represent a physical, compressible flow field?
Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2 (2116 lb/ft2), respectively. Consider the nonlifting flow over a circular cylinder of a given radius,where V∞ = 20 ft/s. If V∞ is doubled, that is, V∞ = 40 ft/s, does theshape of the streamlines change? Explain.
A power plant discharges cooling water through the manifoldin Fig. which is 55 cm in diameter and 8 m highand is perforated with 25,000 holes 1 cm in diameter. Does this manifold simulate a line source? If so, what is theequivalent source strength m?
Air flows at 1.2 m/s along with a flat surface when it encountersa jet of air issuing from the horizontal wall at point A, as inFig. P8.16. The jet volume flow is 0.4 m3/s per unit depthinto the paper. If the jet is approximated as an inviscid linesource, (a) locate the stagnation point S on the wall.(b) How far vertically will the jet flow extend into the stream?
Water flows through a two-dimensional narrowing wedgeat 9.96 gal/min per meter of width into the paper(Fig. P4.72). If this inward flow is purely radial, find anexpression, in SI units, for ( a ) the stream function and( b ) the velocity potential of the flow. Assume onedimensionalflow. The included angle of the wedge is 45 ° .

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS