The wall of a 5 m high cylinderical steel tank (ks= 20 W/mK) of inner diameter 1.5 m and 200 mm thick contains hot oil at 100 C. On the outside of the tank 12 mm of spray urethane insulation is added to stop the oil from cooling. If the worst outside temperature is -6 , (hi = 16 W/m^2 K) and (ho = 5 W/m^2 K) how much heat needs to be added to keep the tank at 100 C for pumping reasons and what are the overall heat transfer coefficients Uo and Ui?

The wall of a 5 m high cylinderical steel tank (ks= 20 W/mK) of inner diameter 1.5 m and 200 mm thick contains hot oil at 100 C. On the outside of the tank 12 mm of spray urethane insulation is added to stop the oil from cooling. If the worst outside temperature is -6 , (hi = 16 W/m^2 K) and (ho = 5 W/m^2 K) how much heat needs to be added to keep the tank at 100 C for pumping reasons and what are the overall heat transfer coefficients Uo and Ui?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.38P: 2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from...

See similar textbooks

Similar questions

3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
/ Hot square plate (1 m ×1 m) is to be cooled by attaching aluminum circular pin fins (D=0.25 cm, L= 3 cm) distributed with distance 0.6 cm as illustrated in Figs.(1-a) & (1-b). If the fin base temperature is 100°C, cooling air temperature is 30°C and h= 35 W/m. °C. Determine the total rate of heat transfer from the finned plate and the effectiveness of the fins? Assume k= 237 W/m.°C and nr=tanh mL/ mL.
Find the minimum amount of diameter for the insulation of a spherical water tank? Radius of the tank is 10 m, thermal conductivity is 25 W/(m^2*K) and convective coefficient is 5 W/(m*K) 8 m not sufficient information 10 m 20 m 15 m
A 50-cm-diameter pipeline in the Arctic carries hot oil at 30◦C and is exposed to a surrounding temperature of −20◦C. A special powder insulation 5 cm thick surrounds the pipe and has a thermal conductivity of 7 mW/m · ◦C. The convection heat-transfer coefficient on the outside of the pipe is 9 W/m2 · ◦C. Estimate the energy loss from the pipe per meter of length. (Please give step-by-step solution)
4.) A 15-cm-diameter steam line carries saturated steam at 6 MPa and is located in a tunnel with stagnant air with a temperature of 50oC. The outside unit convective coefficient is 8.5 W/m2-K. The steam line is covered with 3 cm of 85% magnesia insulation. It is decided to reduce the heat loss by one-half. How much 85% magnesia insulation is required? Neglect thermal resistance of pipe and inside surface.
Calculate the heat losses per unit length in a horizontal tube with an outside diameter of 15 cm, if its surface is kept at 400 K AND the surrounding air has a temperature of 300 K and a pressure of 1 bar.The properties of air at a pressure of 1 bar and a film temperature of 350 K are: In this case, v = 20.76 x 10-6 m2/s , α = 0.2983 x 10-4 m2/s, k = 0.03003 W/mK, Pr = 0.697, β = 2.86 x 10-3 K-1
Two pin fins are identical, except that the diameter of one of them is twice the diameter of the other. For which fin is the (a) fin effectiveness and (b) fin efficiency higher? Explain.
A 12-m-long and 5-m-high wall is constructed of two layers of 1-cm-thick sheetrock (k = 0.17 W/m·K) spaced 16 cm by wood studs (k = 0.11 W/m·K) whose cross section is 16 cm * 5 cm. The studs are placed vertically 60 cm apart, and the space between them is filled with fiberglass insulation (k = 0.034 W/m·K). The house is maintained at 20°C and the ambient temperature outside is 29°C. Taking the heat transfer coefficients at the inner and outer surfaces of the house to be 8.3 and 34 W/m2·K, respectively, determine (a) the thermal resistance of the wall considering a representative section of it and (b) the rate of heat transfer through the wall.
A 50-cm diameter pipeline in the Arctic carries hot oil where the outer surface is maintained at 30 °C and is exposed to a surrounding temperature of -17 °C. The convection heat-transfer coefficient on the outside of the pipe is 9 W/m2 °C. Estimate the energy loss from the pipe per meter of length.
Estimate the natural convection heat transfer coefficient of the horizontal pipe. The outer surface temperature of the pipe is 80 ° C. The ambient air temperature is 40 ° C. The outer diameter of the pipe is 18 cm. Convection coefficient = Answer W / m² ° C.
In a new residential project, you strongly believe thatdouble-paned windows are ‘better’ than single-paned windows.Compare the rate of heat loss between single and double-panedwindows (1.5 m x 1 m) if the thickness of each pane is (th = 0.4 cm)and (k = 0.9 W/m.K). The indoor and outdoor temperatures are 18°C and 2 °C, respectively. Thickness of the air gap between thedouble-paned windows is (th = 1 cm), and (k = 0.022 W/m.K).Image credit: Windowwhirl.
....A journal bearing is to be used for a centrifugal pump where the shaft diameter is 50 mm and the bearing length is 80 mm. The ambient and bearing surface temperatures are 20°C and 45°C, respectively. Which of the following is the heat dissipated by the bearing if the heat dissipation coefficient is 280 W/m2-°C? Group of answer choices 56 W 14 W 73 W 28 W