Determine the maximum factored load w1 that the beam can carry based on the ultimate shear capacity of the beam 312 kN at a distance 0.475m from support A. Assume that w2 = 1.61w1. 4. Determine the maximum factored load w₁ that the beam can carry based on the ultimateshear capacity of the beam of 312 kN at a distance 0.475m from support A. Assume thatW₂ = 1.6w₁.W₁W26.8m0.9m CAB

Answered: Image /qna-images/answer/7dcfcf1a-4f40-4755-9344-9225db6c9d8d.jpg

4. Determine the maximum factored load w₁ that the beam can carry based on the ultimate shear capacity of the beam of 312 kN at a distance 0.475m from support A. Assume that W2 = 1.6w1. W₁ W2 6.8m 0.9m C A B

4. Determine the maximum factored load w₁ that the beam can carry based on the ultimate shear capacity of the beam of 312 kN at a distance 0.475m from support A. Assume that W2 = 1.6w1. W₁ W2 6.8m 0.9m C A B

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter15: Braced Cuts

Section: Chapter Questions

Problem 15.11P

See similar textbooks

Related questions

Q: PROBLEM 3 For a catchment in UP, India, the mean monthly temperatures are given. Estimate the runoff…

A: The data is as given

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

Q: Find the value of strain if stress is 45 Mpa and modulus of elasticity 70 MPa

A: Given data : The value of stress σ=45 MPa The value modulus of elasticity E=70 MPa Required :…

Q: A consolidated-undrained test was conducted on a normally consolidated clay sample. The results are…

Q: A standard steel 14 in. Schedule 40 pipe carries, a 650 lb load at the center of a 28 in. span,…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A wood beam is strengthened using two steel plates as shown in the figure below. 6 mm 150 mm C 6 mm…

Q: What does a construction engineer and manager do? What are its duties and outputs?

A: Construction engineering and managers have following job to do .

Q: A lot with given observations below has missing adjoining observations, one has missing bearing and…

Q: ne axial load, shear and bending me O kN/m B

Q: If the free end of a cantilever of span / and flexure rigidity El undergoes a unit displacement…

Q: Answers: 0x = Txy Op2 = i i i MPa MPa MPa

Q: A single-angle tension member, an L90 x 90 x 10, is connected to a gusset plate with 22 mm-diameter…

Q: What are the two main types of Structural Loads? Describe each briefly.

A: To find : Two main types of structural loads .

Q: Solve for the Beam reactions and draw the shear and moment diagram of the following beams using…

Q: 1. A column W 200 x 22 has an unbraced length of 8m which is pinned at the top and fixed at the…

A: For W 200x22 A (area) = 2860 mm2

Q: QUESTION 15 A 20 m normal weight concrete pile is driven into the ground. How long will it take in…

Q: 56kN/m -10 m- BO -5 m

Q: 1. Investigate the adequacy of 2-45x45x6 mm angles back to back to be used as top and bottom chord…

A: Given, Loads, P1=20 kNP2=30 kNP3=25 kN Gusset plate t=8 mm Rivet diameter d=20 mm

Q: carry using factor of sa

Q: Details of a retaining wall are shown in Fig. 5 below. Determine the factor of safety against (a)…

A: Increase the foundation weight to modify resisting moment . Provide shear key to safe in sliding .

Q: Find the value of strain if stress is 45 Mpa and modulus of elasticity 70 MPa

Q: PROBLEM 2 Monthly rainfall values of 50% dependable year at a site selected for construction of…

A: In this question monthly and annual runoff volume is being asked...

Q: The saturated unit weight of a soil is 19.8 kN/m³. The moisture content of the soil is 17.1%.…

Q: A wood beam is strengthened using two steel plates as shown in the figure below. 6 mm 150 mm 6 mm IB…

Q: Determine the specific gravity of soil solids based on the data below: Initial volume of soil in…

Q: A C15x50 (d=381mm and tw=18.19mm) tension member is to be connected by fillet welds to a 20mm thick…

A: Solution: Given;

Q: 1. A floor system consist of a 100mm concrete slab supported by continuous T-beam with a 9m span,…

A: a) Effective flange width, ?? : 1. L/4 = 9/4 = 2.25 m 2. 16t+?? = 16(100) + 280 = 1.88 ? 3. ??? =…

Q: Knowing that at the instant shown assembly A has a velocity of 9 in./s and an acceleration of 15…

Q: For the beam loaded as shown, by conjugate-beam method (CBM). Determine the slope and defled at…

A: Given data:

Q: Find the height of box of 10 kg should to be raised to achieve potential energy of 250 J. Take g=10…

A: Introduction : The given question is related with mechanics . In this question we are provided with…

Q: A Compound Circular Horizontal Curve Have :, A₁ =42° 16', E ₂ =38.08 m AZP.C P.1=62°12` AZP.1 → P.T=…

A: ###Determination of Compound curve of station PI and coordinates of PC AND PCC ,PT

Q: 2.A swimming pool with plan and section shown in Fig. G is filled with water. It has two short tubes…

Q: The following results are obtained from a series of cone penetrometer tests. Mass of empty can, g…

Q: 1. INTERPOLATING CONTOURS GRAPHICALLY. The accompanying tabulation gives elevations of points over…

A: Given, Horizontal scale 6 cm =10 m Index contour=880,885,890 and 895

Q: The overall drag coefficient of an aircraft of weight Wand wing area S is given by Co= a +bC₂² where…

Q: Angela wants to determine the permeability of an aquifer. The aquifer has a test well 300-mm in…

A: The diameter of test well, d=300mmThe radius, r=d2=150mmThe radial distance of first observation…

Q: The saturated unit weight of a soil is 19.8 kN/m³. The moisture content of the soil is 17.1%.…

A: Given data in question Saturated unit weight Water content To find out Dry unit weight

Q: During a flood flow the depth of water in a 12 m wide rectangular channel was found to be 3.5 m and…

Q: An orifice has a coefficient of discharge of 0.62 and a coefficient of contraction of 0.63.…

A: Given data : The value of coefficient of contraction CC=0.63 The value of coefficient of discharge…

Q: A compound circular curve has: R₁ = 500m, R₂ = 750m, A₁ = 38° 20', A2 = 41° 30′ St. P.I = (28+50)…

Q: A 6m cantilever beam 257 mm x 410 mm carries a uniformly distributed dead load (including…

Q: Determine void ratio of soil

A: Given data : The value of moisture content w=12100=0.12 The value of porosity of soil n=0.4 The…

Q: Why does the estimate of probable total cost need to be revised as the project progresses?

A: there are two reasons for revise cost of project as project progress.

Q: What is the maximum shear stress? Where or = -140 Mpa, σy = 205 Mpa, Try= 100 Mpa. 18 Try 8. T Try…

A: Given: Stresses along x and y direction = 140(compressive) and 205 MPa (tensile) respectively Shear…

Q: Explain on essay form why this TWO application methods is best on applying sealant/adhesive.…

Q: Determine roller support reaction

A: Given data : The value of Point load P=15 KN The value of uniformly distributed load w=25 KN/m…

Q: What is its natural water content (in %)? A soil with a liquidity index of 0.164 has a liquid limit…

A: solution Given liquid limit wL=57%plasticity index IP=39%liquidity index IL=0.164

Q: 15. A rectangular channel 6m wide has a depth of 1m flowing with a mean velocity of 0.75m/s.…

Q: 20. A trapezoidal canal, 6m at the bottom and having side slopes 2:1 carries water to a depth of…

Q: A simply supported wood beam with overhang is subjected to uniformly distributed load q. 1m- 250 mm…

A: To find the maximum permissible value of q

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

Determine the maximum factored load w1 that the beam can carry based on the ultimate shear capacity of the beam 312 kN at a distance 0.475m from support A. Assume that w2 = 1.61w1.

4. Determine the maximum factored load w₁ that the beam can carry based on the ultimate
shear capacity of the beam of 312 kN at a distance 0.475m from support A. Assume that
W₂ = 1.6w₁.
W₁
W2
6.8m
0.9m C
A
B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A simply supported beam carries a concentrated load of 31 kN at 7 meters from the left support (1 meters from the right support). Use EI = 80,000 kN-m2. Solve for the slope at the left support in degrees.
A 140 k and force with a slope of 4 vertical and seven horizontal is located on the second water and determine its y component
An L = 27-ft-long soldier beam is used as a key component of an earth retention system at an excavation site. The soldier beam is subjected to a soil loading that is linearly distributed from wA = 510 lb/ft to wC = 200 lb/ft, as shown. The soldier beam can be idealized as a cantilever with a fixed support at A. Added support is supplied by a tieback anchor at B, which exerts a force of P = 5000 lb on the soldier beam at a = 21 ft. Determine the horizontal deflection of the soldier beam at point C. Assume EI = 3.4 × 108 lb·in.2. Deflection is positive to the left.
A wall footing 1 m wide carries a uniform load of 300 kN/m of wall length. Soil weights 16 kN/m^3.Using the influence chart, compute the total vertical increment of the loads at a depth of 3 m from the edge of the strip in kN/m. a. 48 b. 60 c. 156 d. 108
A triangular plate is 2 m wide at the base of 3.6 m deep is vertically submerged in water with the vertex at the watersurface and its base is parallel to the water surface. Compute how far in meters, below the centroid of the plate is the horizontal resultant force acting on each side of it.
Question 3 5 pts What is the larger vertical reaction of a 6- m simply-supported beam carryinga triangular load which varies from 0 at one support and 15 kN/m at the other support? (Answer must be in kN.)
What is the minimum width for the base of a dam 30m high if upward pressure beneath the dam is assumed uniformly from full hydrostatic head at the heel to zero at the toes? Use the resultant of the reacting force cut the base at the downstream edge of the middle third of the base at O and weight of the concrete is 2.5w.
The horizontal component for the 60 kN force is? a. 51.96 kN b. 45.94 kN c. 55.96 kN d. 35.96 kN The vertical component for the 60 kN force is? a. 20 kN b. 25 kN c. 30 kN d. 35 kN
Dam is concrete gravity dam that impounds water both on the upstream and down stream sides. if the coeffient of friction between the base and the dam is 0.34, determine the following: 1. total vertical reaction in kN 2. total horizontal reaction in kN 3. factor of safety against sliding 4. factor of safety against over turning 5. if the hydrostatic uplift varies linearly from 0 at the heel to zero at the toe, determine the foundation pressure.
An L = 23-ft-long soldier beam is used as a key component of an earth retention system at an excavation site. The soldier beam is subjected to a soil loading that is linearly distributed from wA = 410 lb/ft to wC = 290 lb/ft, as shown. The soldier beam can be idealized as a cantilever with a fixed support at A. Added support is supplied by a tieback anchor at B, which exerts a force of P = 4500 lb on the soldier beam at a = 18 ft. Determine the horizontal deflection of the soldier beam at point C. Assume EI = 6.4 × 108 lb·in.2. Deflection is positive to the left.Answer:vC = Type your answer here in.
Determine the allowable shear stress if W= 33,813lb.
Solve for support rections at A, B and C