The weight of the box, shown in the figure, is 145 kg. determine the tension forces in the ropes AB, AC and AD. 32 in 36 in 40 in 60 in 27 in

Q: Calculate the reaction forces at the origin assuming a fixed attachment point at (x, y, z) = (0, 0,…

A: Given data: F1=350 NF2=420 NF3=540 N Need to determine the reaction forces at origin (O).

Q: The percent elongation of a 1040 steel, cold worked 17% is

A: Given: Percent cold work is 17%. To find: Percent elongation = ?   Concept:

Q: or a steel with a 0.2 wt%C, what is the mass fraction and composition of phases at 600 (Please draw…

A:

Q: 8 cm. 8.5 cm. 7.5 cm. 5.5 cm. 6 cm.

A:

Q: Determine the angular velocity, in rpm, of the rotating drum which results in loss of contact…

A: Given data:- Angle=0.9699 rad, and Radius (r) =330 mm To find:-angular velocity of drum

Q: A golfer is attempting to reach the elevated green by hitting his ball under a low-hanging branch in…

A:

Q: Q6:1f the rod fracture at 35% elongation find the percentage difference between engineering and true…

A: Given data:- elongation of bar at fracture is 35% To find :- difference between engineering strain…

Q: Problem1 The rigid body shown below (Fig 1) is subjected to four cable forces applied at different…

A:

Q: 15.The virtual condition boundary is the exact shape of the noncircular feature and equal in size to…

A: Fill in the blanks Positioning of Geometric modeling

Q: 1. Determine the mass flow rate in lbm/s of a liquid (p = 0.8 g/cm³) flowing through a 2 in (inside…

A:

Q: Each of four particles move along the x-axis. Their positions (in meters) as functions of time (in…

A: Introduction In this problem we will calculate the velocity and acceleration of the particle and we…

Q: EB, loop. Water is pumped in a closed loop of total length L = 40m and constant pipe area A = 0.01…

A:

Q: Determine the horizontal and vertical components of reaction on the beam caused by the pin at B and…

A:

Q: Q1: Which one is stronger; pure copper with 10-μm grains or pure copper with 100-um grains? Q2:…

A:

Q: Warm-up/Example "0" We will work through this problem together at the completion of lecture. The…

A: Given data: The beam is fixed at A

Q: # of teeth input gear = 20 # of teeth output gear = 80 What is the gear ratio (in lowest terms)?

A:

Q: A marksman fires a practice round from A toward a target B. If the target diameter is 170 mm and the…

A:

Q: If a throttling valve is connected to the outlet for one of these tanks, whereby air leaves this…

A: given; inlet temperature(T1)=310Kinlet pressure(P1)=500barexit temperature (T2)=305Kexit…

Q: A fireworks show is choreographed to have two shells cross paths at a height of 125 feet and explode…

A:

Q: A dart is thrown horizontally toward X at 20 m/s as shown. O It hits point Y 0.1 s later. What is…

A: Given data: v0x=20 m/st=0.1 s Need to determine the distance between X and Y.

Q: The forces F1 and F2 in the figure are parallel to the x-axis, while the force F3 is perpendicular…

A:

Q: Problem 5. (Grinding Operations and Grinding Machines) (USCS units) In a centerless grinding…

A:

Q: The natural frequency of an undamped vibrating system is 100 rad/s. A damper with a damping factor…

A: given data; natural frequency(ωn)=100rad/sdamping factor(ζ)=0.8damped frequency(ωd)=?

Q: Problem 1 A reservoir of glycerin has a mass of 1,200 kg and a volume of 0.952 cu. m. find a.)…

A:

Q: Q3/Determine the height water will rise due to capillary action in a clean 0.25 in. diameter tube.…

A:

Q: A column has a rectangular cross-section of 10mm x 20mm and a length of 1m. The slenderness ratio of…

A: given data:Cross-sectional dimension is 10 mm×20 mm,Length of the column is 1 m,

Q: a pipe varies jointly with the internal pressure and the diameter of the pipe, and inversely with…

A: Given data as per question The stressσ in pipe varies jointly with the internal pressure(P) and the…

Q: A fireworks show is choreographed to have two shells cross paths at a height of 131 feet and explode…

A:

Q: Problem 2. (Determining Cutting Speeds in Machining Economics) A turning operation is performed with…

A: Given: n=0.12 ; C=60 m/min Length of workpiece→L=450 mm Diameter of the workpiece→D=80 mm…

Q: A package is released from a helicopter moving directly upward at 15 m/s. The package strikes the…

A: Given data: u=15 m/st=16 sec Need to determine the height of the package from the ground when it was…

Q: 3. An open tank is filled with water. The depth of water is 12m. Assume the density of water to be…

A: Gauge pressure is the pressure only due to the water present in the tank and the atmospheric…

Q: calculate the beanding moment and shear force diagrams

A:

Q: Set P₁ = 7 kN, P₂ = 8 kN . (Figure 1) Figure 4m B E 4m 4 m 6 m D

A:

Q: probe is placed in a flow with Poo 25 the probe in kPa? The fluid is perfect with -1 R 2870 1 kg-1…

A: Given data as per questionA probe is placed in a flow withp∞=101.325 kPa, M∞=1.375Fluid is perfect…

Q: ble containing the ideal gas specific heats of various common gases. diffe Uko K

A: Given data as per question P1=150 kPa, T1=39°C P2=150 kPa, T2=337°C

Q: y did we use 3498.28 N in computing for the total elo

A: We have givenThe maximum shearing stress in either spring must not exceed 200 MPaτmax=200 MpaFor…

Q: Find the piston size of a 4-stroke, 4-cylinder engine, given the following Crankshaft rotation =…

A: Given:-Number of strokes (S) = 4Number of cylinder (n) = 4Mean effective pressure (mep) =162 psi =…

Q: X Incorrect A particle moving in the x-y plane has a position vector given by r = 3/2t² i + 2/3t³j,…

A:

Q: As depicted, a column is contained by a rigid material on its x-axis and has initial dimensions of…

A:

Q: under Stiven : load of 66 kip. The diamurer of Rod decrease 0.004 in during load Find average normal…

A: Given              Diameter, d = 2 in                     Load, P = 60 kip Change in diameter =…

Q: It is common practice to assign a larger portion of the location tolerance to the hole.

A: Fill in the blanks.

Q: (A) the net heat energy absorbed during a cyclic process (the difference between heat flowing into…

A: Given: Atmosphere as a Heat Engine To answer: a)what phenomenon or phenomena are a realization of…

Q: The 153-kg wheel has a radius of gyration about its center of mass O of KO = 283 mm. If it rotates…

A:

Q: 7- What are the reasons that make us resort to the plumbing method.

A: Plumbing is a system of pipes and fixtures used in buildings to distribute potable (drinkable)…

Q: 3. [M031] Two Carnot heat engines operate in series. The first heat engine absorbs heat of 100kW at…

A:

Q: 11) An air standard Diesel cycle has a compression ratio of 14. The maximum and minimum cycle…

A:

Q: Required information Problem 07.088 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This is…

A: Given Data- P1=90KPa T1=20'C P2=450KPa R=0.287 KJ/kgK We have find entropy change

Q: A well-insulated rigid tank contains 3.5 kg of a saturated liquid-vapor mixture of water at 200 kPa.…

A: Given at condition 1  mass of saturated liquid vapor mixture = 3.5 kg  Mass of the liquid mf=…

Q: The vena contracta is the section where this minimum flow area occurs in a sudden contraction

A:

Q: Water at 30ºC is able to climb up a clean glass of 0.2 mm diameter tube due to surface tension.The…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.