3. [M031] Two Carnot heat engines operate in series. The first heat engine absorbs heat of 100kW at 400°C while second heat engine rejects heat at 100°C. If the efficiencies of the heat engines are the same, a. Draw the schematic diagram of the system b. Find the intermediate temperature in between the heat engines c. Heat rejected for both heat engines

3. [M031] Two Carnot heat engines operate in series. The first heat engine absorbs heat of 100kW at 400°C while second heat engine rejects heat at 100°C. If the efficiencies of the heat engines are the same, a. Draw the schematic diagram of the system b. Find the intermediate temperature in between the heat engines c. Heat rejected for both heat engines

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Provide a complete given and computation. Include all the decimals. There are received 68,000 kg/h of steam by an ideal regenerated engine, having only one heater, of which the heater receives 15,400 kg/hr the condenser receives the remainder at 0.007 MPa. If the heater pressure is 0.96 MPa, find the state (quality or "SH) of the steam (a) at the heater entrance and (b) at the condenser entrance.
a.) What is the maximum thermal efficiency for a heat cycle with TC = 500°R and TH = 700°R? b.) Now, what is the maximum coefficient of performance for a heat cycle with TC = 500°R and TH = 700°R?
An 500-HP engine with a thermal efficiency of 30% is using a remote radiator which absorbs 20% of the heat supplied to the engine. Cooling system with cooling tower is used with a cooling range of 5°C. The temperature rise after passing the remote radiator is 10°C. Air enters the cooling tower at 30°C dry-bulb; 20°C wet-bulb temperatures and leaves the tower at 38°C & 65%RH. Make a schematic diagram of the system, the process in the provided psychrometric chart and calculate the following: (a.) The amount of cooling water for the engine, kg/min; (b.) The water flow rate in the cooling tower in liters per hour; and (c.) If the heat absorbed by air is 5% of heat absorbed by the cooling tower water, what is the air flow needed in cu.m/hour.
I need help with this review problem for thermo thank you! An inventor claims to have invented a heat engine with QH = 1000 kJ, QL= 500 kJ that produces Wnet = 500 kJ. The device operates between temperatures of TH=1500 K and TL =600 K. This cycle violates which law of thermodynamics, both, or neither?
In an absorption refrigerator, the energy driving the process is sllPplied not as work, but as heat from a gas flame. (Such refrigerators commonly use propane as fuel, and are used in locations where electricity is unavailable. *) Let us define the following symbols, all taken to be positive by definition: Qf = heat input from flame Qe = heat extracted from inside refrigerator Qr = waste heat expelled to room Tf = temperature of flame Te temperature inside refrigerator Tr = room temperature Use the second law of thermodynamics to derive an upper limit on the COP, in terms of the temperatures Tf, Te, and Tr alone.
1.1 Determine the electrical power supplied to a boiler when the temperature of the enteringwater is 20 C and the exiting temperature is 89 C. The flow of.the pressured water is 2 Kg/s. There is anegligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specificheat is c = 4,370 J/(Kg K). There is a 1.5(105) W rate of heat loss from the boiler during this process to asurrounding at 293.2 k. Consider steady state conditions.1.2 Calculate the total rate of entropy production in Problem 1.1.1.3 Calculate the total rate of exergy destruction (W) in Problem 1.1. The dead statetemperature is 293.2 K and pressure is 1 bar.1.4 Calculate the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to theconditions of problem 1.1 if the electrical heating device is replaced with a gas fired boiler. The highheating value (HHV) of the fuel is 50.02 MJ/kg.1.5 Calculate the exergy destroyed in the process described by problem 1.4. The exergy…
1.1 Determine the electrical power supplied to a boiler when the temperature of the enteringwater is 20 C and the exiting temperature is 89 C. The flow of.the pressured water is 2 Kg/s. There is anegligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specificheat is c = 4,370 J/(Kg K). There is a 1.5(105) W rate of heat loss from the boiler during this process to asurrounding at 293.2 k. Consider steady state conditions.1.2 Calculate the total rate of entropy production in Problem 1.1.1.3 Calculate the total rate of exergy destruction (W) in Problem 1.1. The dead statetemperature is 293.2 K and pressure is 1 bar.1.4 Calculate the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to theconditions of problem 1.1 if the electrical heating device is replaced with a gas fired boiler. The highheating value (HHV) of the fuel is 50.02 MJ/kg.1.5 Calculate the exergy destroyed in the process described by problem 1.4. The exergy…
Subject: thermodynamics In a gas turbine generating set, two stages of compression are used with an intercooler between stages. The HP turbine drives the HP compressor, and the LP turbine drives the LP compressor and the generator. The exhaust from the LP turbine passes through a heat exchanger which transfers heat to the air leaving the HP compressor. There is a reheat combustion chamber between turbine stages which raises the gas temperature to 600 ?C, which is also the gas temperature at entry to the HP turbine. The overall pressure ratio is 10/1, each compressor having the same pressure ratio, and the air temperature at entry to the unit is 20 ?C. The heat exchanger thermal ratio may be taken as 0.7, and intercooling is complete between compressor stages. Assume isentropic efficiencies of 0.8 for both compressor stages, and 0.85 for both turbine stages, and that 2% of the work of each turbine is used in overcoming friction. Neglecting all losses in pressure, and assuming that…
It is required to analyze the operation of an Electric Power Plant called EcomEnergy S.A, the main operator and manager of the plant need to hire a mechanical engineer to calculate the following:a) The reheating temperature so that the output of turbine 1 is saturated steam (high quality mixtures are not allowed).b) For this reheating process, the total power output of the turbines must be calculated.c) The total heat transfer of the boiler.d) Make the T vr S Diagram, include all possible states (1,2,3,4…) and temperature and pressure data.Ecom Energy produces steam at 3 MPa, 600°C in the boiler. In addition, it maintains the condenser at 45°C by transferring 10 MW as heat output.In turbine 1 an expansion is carried out up to 500 kPa and then the flow is reheated, followed by expansion in low pressure turbine 2.
01 A certain heat engine rejects -14.2 kJ of heat from the system to the environment at T=300 K each time the thermodynamic cycle is complete (that is, QL= -14.2 kJ, TL = 300K). At the same time, Wnet = +56.8 kJ of work is output from the cycle. Determine the minimum temp, TH at which heat QH must be supplied to the heat engine.
1 kg of steam at initial conditions of 5.1 MPa and 370 °C expands in a turbine until it becomes saturated. It is withdrawn and reheated to 340°C. After further expansion in the turbine to 160 , part of the steam is extracted for feedwater heating. The remaining steam expands to the condenser pressure of 0.018 MPa. find Wnet, Ec, Ee and the ideal steam rate. Remember, 1. For values taken from the steam tables: Use them as is, do not round off. 2. For values obtained by interpolation and final answers obtained by solving, use FOUR (4) decimal places. 3. PLEASE USE THE STEAM TABLE PROVIDED: https://drive.google.com/drive/folders/15t3WMv7xSTHmwXWXp0X2ZV6aYWhXuRCS?usp=sharing
A factory uses superheated steam (P = 15 bar, T = 250 oC) for heating purposes of 20,000 tons/month. Steam is made in a boiler-furnace using 2 (two) types of fuel, namely coal fuel (LHV = 5500 kcal/kg) and heavy fuel oil (137129 Btu/ft3, density = 0.98 m3/kg) Question: a. How much coal fuel is needed to produce steam with the above specifications if the overall efficiency of the system (boiler-furnace = 75%)! b. How much heavy fuel oil is needed to produce steam with the above specifications (boiler-furnace = 75%)! answer every month... Help pleasee.. fast please