The wooden beam shown is made by gluing together planks as shown.8 kN/mGlue80 mmAB80 mm- NA6 m80 mm160 mmDetermine the maximum shear stress in the glue in kPa. (2 decimals)

Answered: The wooden beam shown is made by gluing…

The wooden beam shown is made by gluing together planks as shown. 8 kN/m Glue 80 mm 80 mm - NA 6 m 80 mm 160 mm Determine the maximum shear stress in the glue in kPa. (2 decimals)

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.8.1P: Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.

See similar textbooks

Related questions

Q: assumption of area of the particle-to-particle contacts i

A: This question has been derived from geo technical engineering and the explanation is given below

Q: 66KN 5@2 m = 10 m %3D

A: A loaded beam is given and it has been asked to draw and determine shear force and Bending moment…

Q: Determine the radius of gyration of the cross-sectional area with respect to the x axis. Y 2"I y 12"…

Q: 100 kN Find the horizontal base reactions for the portal frame shown, when the vertical bars have A…

Q: 14. nstant. Determine the reactions at the suppa

A: Given:- load=500 lb/ft To find:- reactions at support

Q: For the following soil properties determine the volume of infiltration at surface saturation (Fs)…

A: Given that ks=1.75 in/hrθs=0.315θi=0.212ψ=-9.15 ini=7.75 in/hr We know that…

Q: Determine if an ASTM A992 (F, = 350 MPa; Fu = 450 MPa) W14x99 has sufficient available strength to…

A: See I am using here Factor axial force = 1750 KN instead of 1180 Force = 335 kN instead of 225 KN,…

Q: Currently, contractors have over 6 projects on the books; however, the construction of a…

A: a) When we go about investigating the challenges on the fully-fledged Academy site these challenges…

Q: Design a 350 mm x 500 mm rectangular beam to resist a factored moment of 630 kN-m. Assume concrete…

Q: 1 What type of curves or surfaces might be used in a graphical representation of physical phenomena…

A: Various types of Graphical Representation: Bar Graph: The bar graph contains a vertical axis and a…

Q: From the given figure below. Determine the R1, R2, and the length of the compound curve.

Q: An architect-engineering firm is planning a parking lot to accommodate 400 vehicles. Each parking…

A: Given:- The number of vehicles to accommodate in a parking lot = 400 vehicles The dimension of each…

Q: *use 2 decimal places in every values

A: Area of the beam is…

Q: Solve for the end moments consider sidesway 60KN 10KN/m 2m 2m B A 1.51 1.51 5m 21 21 21 4m 4m

Q: Q5: Calculate the force exerted by the piston at A to hold the curved gate in the position shown in…

Q: after

Q: A concrete post is reinforced with 4-28mm diameter steel bars. Compute the stress in each material…

Q: Heat power loss from a district heating line with two separate pipes: How big is the loss in W / m?…

Q: Please find footing by C/C method , full detail please note/all dim in mm

Q: a) Allowable compressive stress b) Allowable bending stress c) Maximum axial load

A: Uniformly distributed load (UDL): -It is a load which is distributed uniformly throughout the…

Q: Find the reaction at points A and B below: 50k/ ft 40 kip 50 kips- ft A B - 4.5 ft- 5ft- 8 ft

Q: what do they mean asset mapping

A: Need to explain Asset mapping

Q: What is the maximum moment of the beam in KN.n

A: To find maximum bending moment

Q: The soil moisture at field capacity and during irrigation is 27.2% and 19.85%, respectively. The…

Q: Determine the discharges in channels having the following sections for y = 6 ft, n = 0.015, and S =…

Q: A C8 × 11.5 is connected to a gusset plate with 22 mm diameter bolts as shown. The steel is A572…

A: Given:- A C8×11.5 is connected to a gusset plate The diameter of the bolts = 22 mm The steel grade…

Q: Given: Beam with loading and supports shown Maximum allowable stress in the steel bar is 30 ksi…

Q: 2. Solve for the Slope at B and the support reactions of the beam shown below using both 3ME and…

Q: TRUE OR FALSE: Parallel lines in multiview drawing should also appear parallel in isometric…

Q: An architect-engineering firm is planning a parking lot to accommodate 400 vehicles. Each parking…

A: Given:- The total number of vehicles to accommodate = 400 vehicles The dimension of each parking…

Q: Using the soil field capacity in the area in Problem No. 2, compute for the volume of water needed…

A: 3. Given data Field capacity FC = 27.2% = 0.272 PWP = 12.43% = 0.1243 Readily available moisture…

Q: The moment of inertia of the rectangle about the x-axis equals. k 5cm 2cm 1cm O 56 cm4 24 cm4

Q: , C Please correct answer

A: Resultant force…

Q: A rectangular channel with bottom width of 4.0 m and a bottom slope of 0.0008 has a discharge of…

Q: A concrete beam of rectangular cross-section of size 120 mm (width) and 200 mm (depth) is…

A: Given data: Width = 120 mm Depth = 200 mm Pre-stressed force = 150 kN Eccentricity = 20 mm (below…

Q: PI Elev 108.00m 1.50m -3% +6% 8.00m A Sta 1+060 PT PC Sta 1+000 Elev 100.00m

Q: Determine the pressure difference between points A and B in Fig. 2-51. I Pa+ [(0.88)(9.79)](0.21) –…

Q: Solve the capacity of a 4.2-m steel column, pin-supported at both ends, having the cross section as…

A: Load carrying capacity = Cross Sectional area * Fy Cross-sectional area = (2*300*45)+(300*55)= 43500…

Q: A retaining vertical wall 5 m high, retaining a sand of unit weight 17 kN/m3 for which e = 35°, the…

A: Effective unit weight = Saturated unit weight - Unit weight of water Due to rise of water table…

Q: A unit volume of a mass of saturated soil is subjected to horizontal seepage. The saturated unit wt.…

Q: Determine the values of the reaction in each beam. 1.5P (KN/m) 2 m 6 m 3P (KNm)

Q: The coefficients of permeability of a soil in

Q: 3. A 300 m3 volume V hydraulic flocculation basin with 24 channels with velocity 0.2 m/s and 23…

A: Flocculation : Flocculation is a condition in civil engineering in which clays, polymers, or other…

Q: Water flows from a large tank through an orifice and discharges to the atmosphere, as shown. The…

Q: Q)A gravity masonry dam is 8 m high and 2 m at the top with an upstream face vertical. The width of…

Q: (b) Water is delivered from a truck (shown in Figure 1b) to a maximum 18m height above the hydrant.…

A: Using Bernoullis theorem the head imparted by the truck to water can be calculated. Then using the…

Q: A vertical cylindrical pile having a diameter of 0.4 m is installed in water that is 10 m deep. For…

Q: A porous media is overlain by water. A pressure of 100 psia is exerted o he other end of porous…

Q: Given: Beam with loading and supports shown Maximum allowable stress in the steel bar is 30 ksi…

Q: A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform…

Concept explainers

Properties of materials

A property of a material describes its characteristics and distinguishes it from the others. The material properties are described it in terms of its hardness, color, appearances, and so on. The material properties generally depend on the type of material, or whether it is a metal or an alloy. There are different kinds of material properties such as mechanical properties, thermal properties, physical properties, and chemical properties. Chemical properties describe the material in terms of a chemical change. The mechanical properties come into existence when the material is acted upon by an external load. Thermal properties are associated with the temperature of the material and specific heat.

Question

The wooden beam shown is made by gluing together planks as shown.
8 kN/m
Glue
80 mm
A
B
80 mm
- NA
6 m
80 mm
160 mm
Determine the maximum shear stress in the glue in kPa. (2 decimals)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the rivet connection shown in figure 2-4, the allowable shearing stress in the 25mm rivets is 140 MPa. Assume the plates are adequate to transmit the load to the rivets. P= 60 KN. a) Determine the shearing stress in the most stressed rivet. b) Determine the maximum allowable value of P. c) If P=80 KN, determine the minimum diameter of rivets. USE NSCP 2015. Thanks.
A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter db / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gb = 28 Gpa.
What is the minimum required bolt diameter (mm) at C ifthe allowable bolt shear stress is 68 Mpa.a. 9 mm c. 11 mmb. 10 mm d. 12 mm Determine the stress (Mpa) in strut BC.a. 5.6 MPa c. 3.2 MPab. 2.8 MPa d. 6.4 MPa Calculate the bolt stress (Mpa) at A if its diameter is 20mm.a. 7.64 MPa c.11.46 MPab. 3.82 MPa d.14.92 MPa
A W 12 X 35 steel cantilever beam is subjectedto an axial load P =10 kips and a transverse loadV =15 kips. The beam has length L = 6 ft. (a) Calculatethe principal normal stresses and the maximumshear stress for an element located at C near the fixedsupport. Neglect the weight of the beam. (b) Repeat Parta for point D which is 4 in. above point C (see figure).See Table F-1(a), Appendix F, for beam properties.
The following solid aluminum bar (E = 10,000 ksi; α = 11.70E-06/F) is located between two fixed supports. Segment AB has a diameter of 3 inches and segment CB has a diameter of 2 inches. The load P is equal to 25 kip and the temperature increases by 50°F. Determine: a. The reactions at the supports. Answ: Cy = 17.938 kip (downward); Ay = 42.938 kip (upward). b. The deformation at point B. Answ: 2.693E-03 pulg. c. The stress in both segments. Anws: 5.709 ksi, 6.07 ksi.
The steel tie bar shown in Figure 2 is to be designed to carry a tensile force of magnitude P = 30 kips whenbolted between double brackets at A and B. the bar will be fabricated from 0.5* ? inches thick plate. Forthe grade of steel to be used, the maximum allowable stresses are: Normal stress = σn = 25 ksi, Bearingstress = σb = 55 ksi and Shearing stress = τ = 4.5* ? ksi. Solve for the values of (a) the diameter d of thebolt, (b) the dimension b at each end of the bar and (c) the dimension h of the bar.
A flanged bolt coupling consists of six - ½ inch steel bolts evenly spaced around a bolt circle of 12 inch in diameter, and four – ¾ inch aluminum bolts on a concentric bolt circle 8 inches in diameter. With an applied torque of 260 kips*inch. determine the max shearing stress in the aluminum and steel bolt. Use Gst = 12x10 6 psi and Gal = 4x106 psi
1. For the riveted connection shown in the figure using elastic analysisa. Determine the safe value of P if the allowable shearing stress of 25mm rivets is 150MPab. Determine the maximum shearing stress that can be develop in the rivet for a given load ? = 52??c. Determine the minimum shearing stress that can be develop in the rivet for a given load ? = 52?N
A laminated plastic beam of square cross section is built up by gluing together three strips, each 20 mm x 60 mm in cross section (see figure). The beam has a total weight of 4.6 N and is simply supported with span length L = 460 mm. Considering the weight of the beam (q) calculate the maximum permissible CCW moment M that may be placed at the right support. (a) If the allowable shear stress in the glued joints is 0.4 MPa. Round to the nearest tenth. Mmax = __ N • m (b) If the allowable bending stress in the plastic is 8 MPa. Round to the nearest hundredth. Mmax = __ N • m
The bar 1 consists of an aluminum cover and a brass core. The data is presented in the table. Determine: a. The maximum force P that can be applied at C. Answ: 84.22 kN. b. The deformation at the point where the load is applied. Answ: 1.5278 mm.
The vertical member shown in Figure STCN17.02 consist of two angles welded to the 8-mm thick gusset plate. Given the following data: Angle size: 75 mm x 50 mm x 6 mm (long legs back-to-back) Area of one angle = 738 mm Size of weld = 6 mm Yield strength of steel, Fy = 248 MPa Allowable weld shear stress, F, = 124 MPa a = 25 mm a. Determine the safe capacity of the vertical member in kN. b. If P= 185 kN, determine the length of weld L2 (mm) such that each weld have equal shear stress. Neglect end returns. c. If L1 = 140 mm and L2 = 70 mm, determine the safe load P (kN) based on weld capacity assuming all welds have equal stress. AP L1 L2
The axial load 396 kN applied to the lap joint is distributed equally among the three 20.6-mm-diameter rivets. What is the maximum tensile stress (in MPa) in the plate if w = 135.4mm and t = 27.1mm? Round off the final answer to three decimal places.