The working current has a power of 100 kW and a power factor of 0.50. After a capacitor of 75 KVAR is installed, what does the power factor become?

Q: A refrigeration system is to be designed to maintain the temperature in the range of -15°C to -5°C,…

A:

Q: rod of the fixed hydraulic cylinder is moving to the left with a constant speed VA = 37 mm/s slider…

A:

Q: 3. A race car C travels around the horizontal circular track that has a radius of 300ft. If the car…

A: Given:Radius of circular track, r = 300 ftTangential acceleration, at = 7 ft/s2 Initial speed, u = 0…

Q: The fork lift has a weight of 2,400 lb and a center of gravity at G. If the rear wheels are powered,…

A: Weight of the forklift, Wf = 2400 lbWeight of the crate, Wc = 300 lbstatic friction between wheels…

Q: An instrument package is held underwater by a cable attached to the floor of the ocean. The…

A:

Q: Water is boiled at 100°C electrically by a 3-kW resistance wire. Determine the rate of evaporation…

A: Given dataThe temperature of the water is.The power of the resistance wire is at temperature of the…

Q: The 10-1b box is projected up a smooth vertical circular Track as shown. When the box reaches 045",…

A: Given:To find:A) Sketch a Free body diagram and a kinetic diagram of the box at this instant.B)…

Q: A FD = 150 N 25° 330 mm D 1500 N/m 110 mm. 75° 120 N = FB X

A:

Q: Draw the shear diagram for the beam. Click on "add vertical line off" to add discontinuity lines.…

A: Draw the shear diagram for the beam.

Q: Use constant specific heats at room temperature in solving the problem. An air-standard cycle with…

A: The air standard cycle consists of three processes:Process 1-2: Constant volume heat additionProcess…

Q: Tung accidentally released, and the pole falls to the ground. Plot the x- and y-components of the…

A: The uniform power pole of mass m and length L is hoisted into a vertical position with its lower end…

Q: Determine the solution of the inviscid Burgers' equation for the double-shock pro- file given by u₁…

A:

Q: Part 2: Suppose, a vertical roller support is added at point C. Use only Area-Moment method. 1.…

A: Given:The flexural rigidity  is constant.To find:

Q: 3. A refrigerator uses refrigerant-134a as its working fluid and operates on the ideal vapor-…

A: Given : The evaporator temperature is TThe pressure at the con dens or is the T-s diagram is,

Q: Force B is parallel the xy-plane. Force D is parallel to the yz-plane What is the moment of Force D…

A:

Q: How could the fluid flow variable be introduced into the following simplified Navier-Stokes…

A:

Q: A scow 20ft wide and 60 ft long has a gross weight of 225 short tons (2000 lb). Its center of…

A:

Q: The equation of motion for a damped multidegree of freedom system is given by Where [m] = [m]{x} +…

A:

Q: 4 HO PROBLEM: Based on the Orthographic Projections of the TERMINAL BLOCK draw a full section.

A:

Q: The 24T 6-pitch 20° pinion 2 shown in the figure rotates clockwise at 1300 rev/min and is driven at…

A: Given:

Q: 2. Figure 2 shows a quick return mechanism. The ram at C has a mass of 50kg and is accelerating to…

A:

Q: For the simply supported beam with loads as shown below, find out the values of shear force and…

A: For the simply supported beam with loads as shown below,Find out the values of shear force and…

Q: Consider the diagram of the 115 kg beam supporting a 75 kg mass. What is the tension in the cable…

A: Draw FBD

Q: A shaft used in an aircraft engine is 50 mm diameter, the maximum allowable shear stress is 84…

A:

Q: The image below shows a slider-crank mechanism. The velocity of the slider (piston) at point C is 26…

A: The image below shows a slider-crank mechanism.The velocity of the slider (piston) at point C is 26…

Q: If a pool is irregularly shaped and a person being assessed has a weight mg= 800 N but weighs Fn=…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Calculate the stress concentration factor (kt). the small diameter is 0.88 in and the bigger one is…

A: Given:To find:Stress concentration factor.New stresses values.

Q: Use the method of nodes to determine the strength in each member of the truss shown. Establish…

A: Use the method of nodes to determine the strength in each member of the truss shown.Establish…

Q: A main supply line in which water flows at 320°C, 150 MPa, is connected through a valve to an…

A:

Q: In the last few steps, where did 0.4 come from?

A:

Q: A horizontal-axis wind turbine with rotor 80m in diameter is 35% efficient in 18m/s wind at 0.977…

A: The power available in the wind can be calculated using the formula:…

Q: To replace the regular light bulb with a high-efficiency light bulb, what is the upper price limit…

A: Unit cost of electricity, Type of light bulbCost ($/piece)Power (W)Lifetime (hours)Regular…

Q: A water tank open to the atmosphere has a hole in the side such that water shoots out horizontally…

A:

Q: Compute the moment arm for the force in cable C, measured relative to the AB axis. Use d₁ = 3.5 ft,…

A:

Q: A rectangular glass window pane on a house has a width of 1.4 m, a height of 2.2 m, and a thickness…

A: Given:The width of the window is the height of the window is the thickness of the window is the…

Q: A vapor compression refrigeration cycle operates at steady flow conditions with 0.25 kg/s or R-134a.…

A:

Q: 2) The small body has a speed, v= 5m/s, at point A. Neglecting friction, determine its speed at…

A:

Q: napes to determine the x and y positions of the centroid relative to the pos artesian coordinate…

A: Given datal=0.55in

Q: Given the information for a motor, determine its LCC in term of present worth (in $). Annual…

A:

Q: Take P= 38 kN. EI is constant. (Figure 1) Figure 4 m B- 2 m- P 1 of 1 Determine the y-component of…

A: Determine the y-component of the reaction at the roller B.Determine the x component of the reaction…

Q: A solid rectangular shaft of cross-section 80 mm x 50 mm is welded by a 5 mm fillet weld on all…

A: To Find:the maximum torque that can be applied to the shaft.Given:The shear stress is the thickness…

Q: Calculate the moment of inertia with respect to the X–X centroidal axes for the areas shown.

A:

Q: ( Y = √₂49 Ø₂ T hule Consider the cylindrical tank dranging due granty through a from hole Tani…

A:

Q: . 16.27 The 10-in.-radius brake drum is attached to a larger flywheel that is not shown. The total…

A: The free-body diagrams of the forces acting on the brake drum and the forces acting about point D…

Q: A pumped storage scheme comprises two reversible pump turbines which transfer water between an upper…

A: Disclaimer:Hello. Since you have submitted multiple questions, we will solve the first one for you.…

Q: The pressure on the suction side of pumps is typically low, and the surfaces on that side of the…

A: Cavitation is a process in which the pressure of a liquid becomes so low that it starts to boil and…

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 50 MPa.…

A:

Q: (Viscous flow) A viscous liquid (μ = 0.015 lbs/ft², p = 1.74 slugs/ft3) flows through the annular…

A:

Q: A vapor compression refrigeration cycle operates at steady flow conditions with 0.25 kg/s or R-134a.…

A: ''Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: (i) What is the 3rd law of thermodynamics? Under what circumstances does this not hold? (ii) Define…

A: Since all the three questions are different, according to our guidelines, we are supposed to answer…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.