Thewould fail whentheysuddenly unloadedareServo MotorsShunt MotorsSeries MotorsStepper Motors

At no load starting of DC series motors speed is increase abruptly and will fail the Motors and…

Answered: The would fail when

Engineering

Electrical Engineering

The would fail when

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter50: Dynamic And Regenerative Braking

Section: Chapter Questions

Problem 4SQ

See similar textbooks

Related questions

Q: It is the Insulator used when the Transmission Lines' path need to take a turn on a sharp corner or…

A: Choose the correct option Which insulator is used to change path of transmission line or dead end.…

Q: Explain the status flags for the operation AEH+37H

A: I have provided an explanation for 8086. This result can also be applied to 8085 ignoring overflow…

Q: 1.Which is an appropriate light source? a. 2. Which device may suit the block for the photodiode? a.…

A: Answer 1- Since photo diode absorbed the light emitted by the source ,here in the given options…

Q: Explain, with the aid of a sketch, the Relay.

A: Power system has currents flowing through transmission lines. These current should be within limits.…

Q: Considering the first column of the "final" Routh Table generated, how many sign change occurred?

A: Open Loop System (OLS)-A system having a input in the system which does not depends on the system…

Q: round and er?

A: A bipolar transistor is a three terminal device used as an amplifier circuit for an electronic…

Q: Complete the membership table to show (AUB) - (AnB) = B,

A: AND gate- It's output is high only when both the inputs are high, if not then output is low. OR…

Q: Draw the ladder diagram of the given relay diagram

A: Two relay logic diagrams are given. We need to draw the ladder diagram.

Q: Which of the following is NOT included in MMDST kit? Small bell with 2 ½ inch diameter opening…

A: The solution is given below.

Q: Which button is used to cut the component in LTspice program?

A: Electrical circuits are designed for various experiments. The circuit is first run on a circuit…

Q: Question 2. Select the correct statement regarding the modulated ASK waveform. a. There is no…

A: The answer is provided below:-

Q: What is the box fill volume allowance for conductors that do not leave the box? O depends on number…

A: Here is your answer! I hope this will help you. The correct options are : Option A : depends on…

Q: If push button is used of switching OFF the motor, the terminals to be connected in push button is…

A: The push buttons are momentary. That means they are used as momentary switches. The cases in the…

Q: t down secondary barrier equipment to protect lab personnel.

A: In an electrical lab it is always advisable to take precautions while doing any experiment because…

Q: A letter designation SL on an electrical drawing indicates a ?

A: In this question we will write letter designation SL on an electrical drawing.....

Q: Attach the proper eve

Q: Which statements are correct regarding the picture?

A: Image shows Airbus electrical system.

Q: Draw a one line diagram showing a bell that rings in absence of flow.include a swtich to turn off…

A: The flow switch is a mechanical device that sends, trip signals to the motor or any other device…

Q: Number 23 please.

Q: Q.26 Why is shielded wire used for signal runs? Select one: A. TO PREVENT VOLTAGE SPIKES B. TO…

A: From this question we need to know why we use shielded wire for signal runs :

Q: Difference between Ring and Johnson counter. Write verilog code for Johnson counter

A: Synchronous counters: In synchronous counter all the flip flop are connected with the same flip…

Q: What are application of verilog keyword begin end and join -fork

A: Verilog is Hardware Description language . The memory and array declaration in Verilog is static in…

Q: Identify the electrical symbol.

Q: Identify the Electrical Symbol

A: LP stands for light pole . It is used in power outputs.

Q: can you tell the letter of the correct answer?

Q: By which of the following command, you can draw a ?rectangle in AutoCAD POL O ARC

A: AutoCAD is a software which is used to design different circuits it is used in designing of…

Q: For each of the following instructions, indicate the flag condition necessary for each jump to…

A: The solution is provided in the following section.

Q: What is the value of ix?

A: Brief description: For the above given question we need to calculate the value of current ix.

Q: | V= C- --- )v 22 2A Answer:

A: The equivalent circuit with assumed directions of current in each resistor and assumed voltage at…

Q: What is the difference between the white and pink noise ?

Q: Symbol of LED

Q: X) Answer the following questions (d)For a positive going pulse, mention the leading edge and…

Q: Why it should be used in both sides (transmitter and receiver) in the radar system.

A: Radars- Radars have very large wave length. Since radio waves can have very length and also the…

Q: Explain the working of Chart type recorder with a neat diagram.

A: Chart type recorder - The chart recorder is an instrument. it is used to record different process…

Q: Where does the 10 come from?

Q: CCA stands for common ampere Select one : False or True

A: CCA stands for 'Common Collector Amplifier' not common ampere.

Q: Mark all the parts of gas pressure cable in pictures

A: Gas pressure cable : it an coaxial or simple cable which filled with inert gas like nitrogen at…

Q: what is The fundomantal requairmiantof footCAfve Yelaying ?

A: As per the guidelines of Bartleby we supposed to answer first first question only.

Q: How Know the Q is lasing leading to thow

Q: Compared between clipper and calmper

A: The comparison between clipper and clamper is as follows.

Q: 21 - Radio copy should consist of short, familiar terms. True False

A: Radio copy is an informal and conversational and it consist of the short, familiar terms, to attract…

Q: X) Answer the following questions (answers to be typed, handwritten answer for this question will…

A: First let us understand what a pulse is A pulse is a burst of energy that can be current, voltage,…

Q: What is the peak carrier voltage? Round your answer to 2 decimal places.

A: Given: A voltage waveform. According to question: Vmax is calculated from the waveform maximum…

Q: Differentiate FM and PM

A: The explanation is as follows.

Q: flab,code):1I(0, 3,6,9,1!,19,20,24,25, 26,27,28, 29, 30) ΠD (,.a,12,13)

Q: . Draw the block diagram of a measuring system.

A: As per bartleby guideline for more than one question asked only first is to be answered please…

Q: What type of modulation scheme is used but IS 95 system

A: In this case, the modulation scheme used by the IS 95 system is to be determined.

Q: The electrically activated switch is called relay Select one : True or false

A: Yes it is TRUE Electrically activated switch is called relay.

Concept explainers

Single Phase Induction Motor

The single-phase induction motor or engine consists of a single rotating phase in the stator and a rotating cage in the rotor. When phase one supply is connected to the stator winding, a magnetic field is generated. In the pulsating field, the rotor does not rotate due to inertia. So, a single-phase import motor does not start and requires some initial methods.

Question

The
would fail when
they
suddenly unloaded
are
Servo Motors
Shunt Motors
Series Motors
Stepper Motors

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the coil pitches and indicate the slots into which the first coil should be placed for the following armature windings: (a) 36 slots, four poles; (b) 76 slots, six poles; (c)270 slots, 10 poles. (Our lesson is DC GENERATORS in the subject ELECTRICAL MACHINE 1) PLEASE GAVE ME A CLEAN ANSWER AND SOLUTION. THANK YOU
DC GENERATOR A shunt generator is connected to a load that draws 28.8 kW. Ra = 0.04 ohm and Rsh = 48 ohms. If the power delivered in the armature is 106.3 % of the power delivered to the load. Determine the terminal voltage of the generator. Please include complete solution.
An alternator is much less likely to burn out on a sustained short-circuit than a separately excited DC generator. Explain.please show your answer clean and readable. Thank you.
An 8 pole, simplex lap wound, shunt generatoe has 800 conductors and a flux per polw of 0.025Wb. The armature and shunt field resistances are 1 ohms and 45 ohms respectively. if a resistance of 11.25 ohms is connected as a load and the machine is running at 800 rpm. calculate the load cureent(in amp)
. A 20 kW compound generator works on full load with terminal voltage of 250 V. The armature, series, and shunt windings have resistances of 0.05-ohm, 0.025 ohm, and 100 ohms, respectively. If the machine is connected short shunt, the emf generated is nearest to. (Our subject is Electrical Machines 1 ) (I need a clear answer and solution. Thank you so much)
ANSWER ALL THE QUESTIONS: A.) Calculate the voltage induced in the armature winding of a 4 pole, wave-wound, dc machine having 728 active conductors and running at 1800rpm. The flux per pole is 30mWb. 1310.4V 468.2 V 720.4 V 236.4 V B.) The direction of rotation of a DC motor is reversed by reversing armature connections adding resistance to the field circuit interchanging the armature and field connection reversing supply connection
*need in 5 mins urgent please* A 6-pole series motor takes 40 A from the supply mains at 220 V. It has 600 lap-wound conductors. The series field resistance and armature resistance are 0.01 ohms and 0.09 ohms respectively. Flux per pole is 29 mWb. Calculate back emf (V).
1. It is a machine that converts mechanical energy to electrical energy. 2. It is a machine that converts electrical energy to mechanical energy. 3. It is cylindrical or drum-shaped where the coils are placed and can either be lap wounded or wave wounded. 4. It connects the commutator to the other parts of the DC machine. 5. It serves as the housing of the dc machine. 6. True or False: The shunt field winding is part of the armature. 7. True or False: The long shunt compound generator is when the armature is in series with the series field winding and parallel to the shunt field winding. 8-10. Your newly built house needs an elevator. Which from the following will be best to use- series, shunt or compound motor and why?
6.a. Arcing in manual starters is eliminated by the use ofA. overload relays.B. nonconductive contacts.C. blowout coils.D. spring-loaded handles.6.b. Chattering of AC contactors is prevented byA. blowout coils.B. air gaps.C. secondary windings.D. shading poles.
• T or F, modify the wrong part if False, please underline twice your answer if True or False. The current that flows in the armature of a DC generator is DC in nature.
7.a. If a 575-volt three-phase motor originally connected in 3-parallel △ is reconnected in 5-parallel Y, thenew voltage isA. 501 volts.B. 794 volts.c. 747 volts. 7.b. The total flux per pole of a reconnected motor is 900,000 lines of force. If the cross-sectional area ofthe laminated core is 6 sq in. and the cross-sectional area of the teeth per pole is 14 sq in., the flux densityin the teeth is approximatelyA. 120,000 lines.B. 101,000 lines.C. 105,000 lines.
Need Asap ? Draw a developed winding diagram for a winding diagram for a PC machine with 4 poles, 26 slots with 4 conductors per slot duplex lap, double-layer. Pole Pitch = 26 YB= 27 YF = 23 Need Diagram must