There are three handles on this door. The hinge needs a moment of 20 Nm to open the door. 3 30 cm 27 cm 28 cm a) Ií handle 1 is pushed with a force of 10 N, nothing happens. Why won't the door open? Hinge Handle 1 Handle 3 b) What (to 1d.p) is the smallest pushing force needed to open the door with handle 2? Handle 2 c) What's the minimum force (to 1 d.p.) needed to open the door with handle 3? d) Why are door handles usually on the opposite side to the hinges?

There are three handles on this door. The hinge needs a moment of 20 Nm to open the door. 3 30 cm 27 cm 28 cm a) Ií handle 1 is pushed with a force of 10 N, nothing happens. Why won't the door open? Hinge Handle 1 Handle 3 b) What (to 1d.p) is the smallest pushing force needed to open the door with handle 2? Handle 2 c) What's the minimum force (to 1 d.p.) needed to open the door with handle 3? d) Why are door handles usually on the opposite side to the hinges?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the rigid frame as shown in FIGURE L, if the pulley weighs 2kN, find the following: 1. Reaction at C a. 8 kNb. 11 kNc. 10 kNd. 9 kN34. Reaction at Ba. 28.9 kNb. 27.28 kNc. 26 kNd. 24.7 kN3. Angle that the reaction at B makes with the horizontal. a. 32.71°b. 24.03°c. 31.98°d. 19.11°
Calculate the vertical reaction at support D. Enter your answer in kN to two decimal places.
Three cables pull on the pipe such that they create a resultant force R. Two of the cables are subjected to known forces as shown. Assuming all forces are coplanar, determine: (a) the partial resultant P of the two known forces and (b) the minimum R if ?? = 23°. What is the corresponding magnitude of F? Also, (c) resolve the minimum R in its components in f and m axes which coincide with the lines of action of the 600 and 400-lb forces, respectively. Note that the sense of F in the figure is just assumed.
In the figure on the right where there is a 50 N single load at point Bof the given rod system, (between AB: 4m / BC: 1m)a) find the support reactions?b) Immediately after support A, just before point Band immediately after and just before the C-bracketFind the cross section effects by cutting?c) Draw the cross sectional influence diagrams.
The frame shown in the figure is supported by a hinge at A and a roller at E. Compute the vertical components of the hinge forces at C as they act upon member AC in kN. P = 28 kN and x = 3.3 m.
(a) Assuming that no loads act in Figure P9.16,compute the reactions if support B is constructed 0.48 in.too low. Given: E = 29,000 kips/in.2, I = 300 in.4. (b) Ifsupport B settles _32 in. under the applied loads, computethe reactions.
A rectangular beam is supported at both ends. It carries two concentrated load of 110kN, a clockwise moment of 110kN-m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 60GPa. Solve the following if the reaction at point B is 328.90256410256kN, upward. BEAM DIMENSION: Width = 190mm , Height = 390mm NOTE: b = 4.8m ; Determine the deflection at midspan
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Show complete and organized solutions. a. Vertical Reaction at B in kN.b. Moment Reaction at A in kN-m.c. Deflection at point C in mm.d. Deflection at midspan of AB in mm. Valuea = 3.7b = 26c = 29 Thank you very much!
5. What is the approximate moment at support a? In kN.m A. -79.86 B. -27.95 C. -73.28 D. 0 E. -10.98 F. 73.28 G. 79.86 H. 10.98 I. 27.95
given w = 8.2 kn/m and p = 15 kn for the beam below Calculate the vertical reaction at support A now. Provide your answer to 2 decimal places. Consider an upwards force as being positive, however only include a sign if the reaction is negative i.e. acts vertically down. Do not provide any units in your answer. Vertical reaction at A [kN] =
The sector gate UE is submerged in water as shown in the figure. The sector gate is one-twelfth pf a circle of radius 4.98m. It has a length of 10.4m. Determine the horizontal components (kN) of the resultant force acting on gate.
The rope exerts a force of magnitude |F|=200 lb. on the top of the pole at B. Determine the magnitude of the moment of F about A.