There is an upward flow of 0.06 ml/s through a sand sample with a coefficient of permeability 3 × 10^–2 mm/s. The thickness of the sample is 150 mm and the cross-sectional area is 4500 mm2.Determine the effective stress in N/m2 at the middle of the sample, if the saturated unit weight of the sample, is 18.9 kN/m3.

There is an upward flow of 0.06 ml/s through a sand sample with a coefficient of permeability 3 × 10^–2 mm/s. The thickness of the sample is 150 mm and the cross-sectional area is 4500 mm2.Determine the effective stress in N/m2 at the middle of the sample, if the saturated unit weight of the sample, is 18.9 kN/m3.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter12: Shear Strength Of Soil

Section: Chapter Questions

Problem 12.18P

See similar textbooks

Similar questions

There is an upward flow of 0.06 ml/s through a sand sample with a coefficient of permeability 3 × 10–2 mm/s. The thickness of the sample is 150 mm and the cross-sectional area is 4500 mm2. Determine the effective stressat the bottom and middle of the sample, if the saturated unit weight of the sample, is 18.9 kN/m3.
In a drained triaxial test on consolidated clay the stress and angle are as follows : Deviator stress is 20 lb/in2 and friction angle 210 . calculate the effective confining pressure at failure.?
There is an upward flow of 0.06 ml/s through a sand sample with a coefficient of permeability 3 × 10^–2 mm/s. The thickness of the sample is 150 mm and the cross-sectional area is 4500 mm2.Determine the effective stress in N/m2 at the middle of the sample, if the saturated unit weight of the sample, is 18.9 kN/m3. a. 177.38 b. 354.75 c. 88.69 d. 709.5
A consolidated drained triaxial is conducted on a normally consolidated soil with chamber confining pressure of 152kPa. If the deviator stress failure is 250kPa, determine the following: a. Calculate the angle of friction of the soil (degrees) b. Calculate the shear stress at the failure plane (kPa) c. Calculate the normal stress at the failure plane (kPa)
There is an upward flow of 0.06 ml/s through a sand sample with a coefficient of permeability 3 × 10^–2 mm/s. The thickness of the sample is 150 mm and the cross-sectional area is 4500 mm2.Determine the effective stress in N/m2 at the bottom the sample, if the saturated unit weight of the sample, is 18.9 kN/m3. Provide Diagram a.709.5 b.177.38 c.88.69 d.354.75
A cylindrical sample of soil having a cohesion of 80 kN/m2 and an angle of internal friction of 20° is subjected to a cell pressure of 100 kN/m2. Determine: c. Determine the normal stress kn Kpa at the failure plane
A consolidated-drained triaxial test on a sand yields the results:All-around confining pressure = σ3 = 30 lb/in2Added axial stress at failure = Δσ = 96 lb/in2Determine the shear stress parameters (i.e., Φ' and c')
In a triaxial test, a specimen of saturated [normally consolidated] clay was consolidated under a chamber confining pressure of 80 kPa. The axial stress on the specimen was then increased through the allowing the drainage from the specimen. The specimen fails when 120 kPa. The pore water pressure at the time was 50 kPa. What is the consolidated undrained friction angle [phi]?
A triaxial test conducted on cohesionless soil gives the following results: Deviator stress at failure = 410kPa The angle of shearing resistance = 32 degrees Determine the following: a. Confining pressure in kPa b. Shear stress at failure plane in kPa c. Angle that the failure plane makes with the principal plane (degrees)
After conducting a tri-axial test on a sand sample, the normal and shearing stress on the failure plane at failure was found to be 475kPa and 350kPa, respectively. Which of the following most nearly gives the plunger stress?
A specimen of clean sand when subjected to direct shear test failed at stress of 1.20 kg/cm2 when normal stress was 1.60 kg/cm2. Determine: Angle of internal friction. Deviator stress at which the failure will take place if a cylindrical sample of the same sand is subjected to tri-axial test with a cell pressure of 1 kg/cm2.