Thermal noise is a type of noise that is produced when electrons move rapidly andrandomly within a conductor due to thermal agitation. Determine the following foran amplifier operating at a temperature of 27°C and a bandwidth of 20 kHz. Assumethat the ambient temperature is 290 Kelvin.(i)the thermal noise power in watts and dBm.(ii)the RMS noise voltage for a 60 Q internal resistance and a 60 Q loadresistance.(iii)the increase in thermal noise power in dB if the temperature increased to70°C.(iv)the increase in thermal noise power caused by doubling the bandwidth.

Answered: Image /qna-images/answer/8430b547-6e24-4ed3-811d-e7652d7c56dc.jpg

Thermal noise is a type of noise that is produced when electrons move rapidly and randomly within a conductor due to thermal agitation. Determine the following for an amplifier operating at a temperature of 27°C and a bandwidth of 20 kHz. Assume that the ambient temperature is 290 Kelvin. (a) (i) the thermal noise power in watts and dBm. (ii) the RMS noise voltage for a 60 N internal resistance and a 60 Q load resistance. (iii) the increase in thermal noise power in dB if the temperature increased to 70°C. (iv) the increase in thermal noise power caused by doubling the bandwidth.

Thermal noise is a type of noise that is produced when electrons move rapidly and randomly within a conductor due to thermal agitation. Determine the following for an amplifier operating at a temperature of 27°C and a bandwidth of 20 kHz. Assume that the ambient temperature is 290 Kelvin. (a) (i) the thermal noise power in watts and dBm. (ii) the RMS noise voltage for a 60 N internal resistance and a 60 Q load resistance. (iii) the increase in thermal noise power in dB if the temperature increased to 70°C. (iv) the increase in thermal noise power caused by doubling the bandwidth.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. For an electronic device operating at a temperature of 17°C with a bandwidth of 10 kHz, determine:a. ThermalnoisepowerinwattsanddBm.b. Rmsnoisevoltagefora100Ωinternalresistance. 2. Two resistors, 20 kΩ and 50 kΩ are at ambient temperature. Calculate for a bandwidth equal to 100 kHz, the thermal noise voltage for the tworesistors connected in parallel.
The ac equivalent circuit for an amplifier is shown . Assume the capacitors have infinite value, RI = 750 Ω, RB = 100 kΩ, RC = 62 kΩ, and R3 = 100 kΩ. Calculate the voltage gain and input resistance for the amplifier if the BJT Q-point is (40μA, 10 V). Assume βo = 100 and VA = 75V.
The ac equivalent circuit for an amplifier is shown . Assume the capacitors have infinite value, RI = 10 kΩ, RB = 5 MΩ, RC = 1.5 MΩ, and R3 = 3.3 MΩ. Calculate the input resistance and output resistance for the amplifier if the BJT Q-point is (2 μA, 2 V). Assume βo = 40 and VA = 50 V.
Figure Q1(a) shows a Class A power amplifier circuit. Given the output signal is as shown in the figure, where Vm is the peak voltage and T is the period. For all transistors, you may neglect VBE and VCE(sat) in your calculations. (i) Derive an equation for power conversion efficiency, in terms of Vm, VCC, I and RL. Hence, deduce the maximum power conversion efficiency that is achievable. (ii) Determine the worst-case average power dissipation in each transistor under normal condition (i.e. RL is not open or short)
a. What is the DC gain of this amplifier? (in dB)b. Where is the input pole frequency located? (in Mrad/sec)c. Where is the output pole frequency located? (in Mrad/sec)
The ac equivalent circuit for an amplifier is shown . Assume the capacitors have infinite value, RI = 10 kΩ, RB = 5 MΩ, RC = 1.5 MΩ, and R3 = 3.3 MΩ. Calculate the input resistance and output resistance for the amplifier if the BJT Q-point is (2 μA, 2 V). Assume βo = 40 and VA = 50 V. Rework the given problem if IC is increased to 100 μA, and the values of RC, RB, and R3 are all reduced by a factor of 50.
What is the output impedance of an Ideal Operation Amplifier? What is the open loop gain of an Ideal Operation Amplifier? What is the gain of a voltage follower operational amplifier circuit? What is the input impedance of this circuit? Draw the circuit. How can I add two voltages values together with on op amp? Using op amps, how to make an AD Converter? A DA Converter? What components determine the frequency of an astable, 555 oscillator? Draw the circuit. Draw a circuit for both an astable and a monostable, 555 multivibrator. What is the duty cycle and percentage duty cycle of a pulse train or square wave? What is the overshoot, rise time, fall time, and pulse width of a pulse and where on the waveform is each measured?
step by step explanation needed. Given a sinusoidal input signal (1 mV amplitude at 5kHz), design a CE-CC amplifier to achieve a 100 mV amplitude sinusoidal signal across a 50ohm load.
Q.4/ Refer to the class AB power amplifier shown below:a. Determine the dc parameters VB(Q1), VB(Q2), ICQ, VCEQ(Q1), VCEQ(Q2).b. For the 5Vrms input, determine the power delivered to the load resistor.c. Determine the approximate input resistance seen by the signal source if ac=100
Figure 2 shows a typical BJT amplifier, with its parasitic capacitances displayed. The current gain of the transistor is B=150 and the voltage gain of the amplifier is Am =-125. The small signal resistances of the transistor are re =16 ohm and r0 = infinity, respectively. The values of resistors and capacitors in the figure are: R1 =80 kohm, R2 =20 Kohm, Rc = 2 Kohm, RE = 2 Kohm, Rs =50 W, RI=5 kohm, Cs=2 uF, Cc=2 uF, Ce =10 uF, Cbc =4 pF, Cbe = 10 pF, Cce =1 pF, Cwi = 4 pF, CWO = 9 pF, and Vcc = 20 V. a) Sketch a simplified circuit diagram of Figure 2 for high frequency analysis. b) Using the concept of "Miller effect capacitance", calculate the input and Output Miller effect capacitances of Figure 2, respectively. C) Determine the upper cut-off frequency of Figure 2 that is imposed by its input network only. d) Explain briefly the possible ways to increase the upper cut-off frequencv of this amplifier.
Given the differential amplifier circuit below. Determine the following: emitter current, differential mode voltage gain, common mode voltage gain and CMRR.
When the ltspice simulation of the circuit shown in the figure is performed, the output voltage (Vout) is obtained as given in which of the figures below? NOTE-1: Vcc = 12 V, RC = 2.2 kΩ, RB = 15 kΩ, RE = 180 Ω and C1 = 1 μF. NOTE-2: For the input voltage Vin, the DC offset voltage is 1.6 V, while the applied sinusoidal signal has a amplitude of 10 mV and a frequency of 10 kHz.