A thermometer is removed from a room where the temperature is 70° F and is taken outside, where the air temperature is 20° F. After one-half minute the thermometer reads 40° F. What is the reading of the thermometer at t = 1 min? (Round your answer decimal places.) OF How long will it take for the thermometer to reach 25° F? (Round your answer to two decimal places.) min

A thermometer is removed from a room where the temperature is 70° F and is taken outside, where the air temperature is 20° F. After one-half minute the thermometer reads 40° F. What is the reading of the thermometer at t = 1 min? (Round your answer decimal places.) OF How long will it take for the thermometer to reach 25° F? (Round your answer to two decimal places.) min

Mathematics For Machine Technology

8th Edition

ISBN:9781337798310

Author:Peterson, John.

Publisher:Peterson, John.

Chapter16: Table Of Decimal Equivalents And Combined Operations Of Decimal Fractions

Section: Chapter Questions

Problem 32A

See similar textbooks

Similar questions

Compute the following problems. Express the answers to the nearest whole number. Use N=12C3.1416D or 12CD for customary units and N=1000C3.1416D or 1000CD for metric units. An annealed cast iron housing is drilled with a cutting speed of 20 meters per minute using a 22-millimeter diameter carbon steel drill. Find the revolutions per minute.
Compute the following problems. Express the answers to 1 decimal place. Use: T=LFN Cast iron, 312 inches in diameter, is turned in a lathe at 270 rpm. Each length of cut is inches and five cuts are required. A carbide tool is fed into the work at 0.015 inch per revolution. What is the total cutting time?
Compute the following problems. Express the answers to the nearest whole number. Use N=12C3.1416D or 12CD for customary units and N=1000C3.1416D or 1000CD for metric units. A high-speed steel milling cutter with a 1.750-inch diameter and a cutting speed of 40 feet per minute is used for a roughing operation on an annealed chromium-nickel steel workpiece. Find the revolutions per minute.
Compute the following problems. Express the answers to the nearer whole number. Use C=3.1416DN12 or DN12 for customary units and C=3.1416DN1000 or DN1000 for metric units. A finishing cut is taken on a brass workpiece using a 100-millimeter diameter carbon steel milling cutter. What is the cutting speed when the cutter is run at 86 r/min?
The formula for the amount A in an investmentaccount with a nominal interest rate r at any timet is given by A(t)=a(e)rt, where a is the amount ofprincipal initially deposited into an account thatcompounds continuously. Prove that the percentageof interest earned to principal at any time t can becalculated with the formula I(t)=ert1.
Repeat the previous exercise to find the formula forthe APY of an account that compounds daily. Usethe results from this and the previous exercise todevelop a function I(n)for the APY of any accountthat compounds n times per year.
Compute the following problems. Express the answers to the nearer whole number. Use C=3.1416DN12 or DN12 for customary units and C=3.1416DN1000 or DN1000 for metric units. What is the surface speed of a 16-inch diameter surface grinder wheel running at1194 rpm?
Compute the following problems. Express the answers to 1 decimal place. Use: T=LFN Fifteen 3.20-millimeter diameter holes each 57.15 millimeters deep are drilled inan aluminum workpiece. The high-speed steel drill runs at 9200 r/min with a feedof 0.05 millimeter per revolution. Determine the total cutting time.
Compute the following problems. Express the answers to 1 decimal place. Use: T=LFN Seven brass plates 9.00 inches wide and 21.00 inches long are machined with amilling cutter along the length of the plates. The entire top face of each plate ismilled. The width of each cut allowing for overlap is 212 inches. Using a feed of0.020 inch per revolution and 525 rpm, determine the total cutting time.