Thickness of the plate is reduced from 40mm to 20mm by succesive cold rolling passes using identical rolls of diameter 600 mm. Assume that there is no change in width. If the coefficient of friction b/w the rolls and the workpiece is 0.1. Determine the minimum number of passes required?

Thickness of the plate is reduced from 40mm to 20mm by succesive cold rolling passes using identical rolls of diameter 600 mm. Assume that there is no change in width. If the coefficient of friction b/w the rolls and the workpiece is 0.1. Determine the minimum number of passes required?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Two ships X and Y sight a distress flare that is 56 nautical miles from X and 78 nautical miles from…

Q: An L-shaped bar ABC has known velocity v and acceleration a, at point A and known ang ular velocity…

Q: blood viscosity and plasma viscosity? Q2. The 0.15m wide plate passes between two layers of oil, A…

Q: If load P = 20.1 kips, determine the normal force in bar (1).

A: given data: P = 20.1 kips To find: normal reaction force from point D, RD = ?

Q: A diesel power station has a fuel consumption of 0.37 lb/ kWh. The calorific value of fuel being…

Q: O 0.3 m 70° m 1m 4 kN 0.5 1.5 m 15 kN-m 10 KN 6 KN 0.3 m Replace the three horizontal forces and…

A: To find: Moment about point O:

Q: A 32 m high down Comer-tank system operates lloo bar if the exit quality of the steam is what will…

A: Given Volume, V = 32 m3 Initial pressure, P1 = 100 bar Quality, x = 0.5…

Q: F₁ = 14 kN a= 270mm, b= 160mm, c= 80mm, and = 45°. Pin B is in a double-shear connection and has a…

Q: Outer surface of a tube-steel oven is at 110 oC. What would be the heat transfer rate to the…

Q: The beam shown in the figure is subjected to two forces. What would be the resultant moment about…

A: Given:- To Find:- Moment about point A (MA) Solution:- Sign convention :- Counterclockwise…

Q: Calculate the reactions at supports A and B of the truss in the figure. Neglect the weight of the…

Q: Qs Air at 1 atm and 40°C flows across a 10 cm diameter cylinder at velocity of 40 m/s. The cylinder…

Q: Cantilever beam loaded as shown in fig., draw the shear force diagram and bending moment diagram. 20…

Q: J A 32m high down comar-tank system operates at 100 bar. the driving exib IF the quality of the…

A: Given Volume, V = 32 m3 Initial pressure, P1 = 100 bar Quality, x = 0.5…

Q: Draw the schematic diagram for each of the following Boolean Expressions: 1. AB X 2. A+B= X 3. X = A…

Q: The rectangular bar is connected to the support bracket with a 10-mm-diameter pin. The bar width is…

Q: Find the Center of Mass of the point masses shown in the figure on the x-axis. Where M1 = 20 kg, M2=…

A: Given data as per the question M1=20 kgM2=40 kgM3=60 kgx1=5mx2=−8 mx3=10 m

Q: determine the overall heat transfer coefficient of a condenser formed of copper pipe when the…

A: Given Data The heat transfer coefficient is: hi=2000 W/m2·°C The refrerant side heat transfer…

Q: true stress of 345 MPa is applied. How much will a specimen of this material elongate when a true…

Q: Evaluate:∫ds

A: From question ∫ds = S + c Where c is Intregated constant.

Q: The velocity of a particle moving in the x-y plane is given by (3.46i + 7.64j) m/s at time t = 4.88…

Q: In the following parallel circuit, what is the equivalent resistance and the total current in the…

Q: A Beam AB is supported by a pin at A and cable BC at B. The vertical component of reaction force at…

A: To find : vertical component of reaction force at pin A (Ay)

Q: A 50 kg man drops from a roof down to a trampoline which can be simplified as a spring with…

Q: If a block is stationary, then the friction force acting on it is Select one: O a. = μs.N O b. ≥…

Q: A flywheel weight = 50 kN with radius of gyration= 1 m losses its speed from 400 rpm to 280 rpm in 5…

Q: Find the Moment of Inertia about the x-exes of the composite shape shown in the figure below. H 6cm…

Q: The Stokes number, St, used in particle-dynamics studies is a dimensionless combination of 5…

Q: 1 m 0.3 m 70° -1 m 4 kN 0.5 m 1.5 m 15 kN m 10 KN 6 KN 0.3 m Replace the three horizontal forces and…

A: SOLUTION - Given data -FA =4 KNFB =6KNFC =10KN

Q: 5-Which of the following is true for a Fanno flow (a) The Mach number always increases as one moves…

A: Fanno flow: It is an adiabatic flow through a constant area duct where the friction effect is…

Q: B. Pure Substance Processes 1. A prototype boiler that contains 5 kg of saturated steam at a…

Q: J A 32m high down comar-tank system operates at loobar. the driving exib IF the quality of the…

A: Given Volume, V = 32 m3 Initial pressure, P1 = 100 bar Quality, x = 0.5…

Q: what is the velocity of the body for the time interval t=1 second to t=5 seconds.

Q: A compound gear train with gears P, Q, R and S has number of teeth 20, 40, 15 and 20 respectively.…

Q: Determine the stress in each section of the bar shown in the Figure when subjected to an axial…

Q: in a rigid body in plane motion, the point R accelerating with respect to point P at 10/180 m/s². If…

Q: 25 marks Q4: For the aluminum pipe shown in figure below (G-27GPa).Determine (a) The torque To…

Q: 0 1 m 0.3 m 70° 1 m 4 kN 0.5 m 1.5 m 15 kN m 10 KN 6 KN 0.3 m Replace the three horizontal forces…

Q: * The overhanging beam shown, Find the reaction value and direction of :the hinge support

Q: 1- What is the pressure at the Economizer (in bar)? 2- What is the pressure at the Evaporator (in…

Q: Given the value of moment of Inertia is=120 x 10^6 mm^4, and the modulus of elasticity of concrete=…

Q: Given the Modulus of elasticity of concrete 50 GPa. what is the value of E in .MPa unit Non of them…

A: Modulus of elasticity = 50GPa Killo = 10^3 Mega = 10^6 Giga =10^9

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

Q: The y-coordinate of a particle in curvilinear motion is given by y = 9.0t³ - 13.3t, where y is in…

A: Write the given data. y=9t3-13.3tax=4.3tv0,x=12.1 in/st=3.2 s Consider the expression of y and…

Q: When an axial load is applied to the ends of the bar shown in Fig. P2.1, the total elongation of the…

Q: 9. During a polytropic process, 10 lb of ideal gas, whose R = 40 ft-lb/lb-ºR, changes state from 20…

A: Solution to first three sub-parts as per our company policy:

Q: Find the Center of Mass of the point masses shown in the figure on the x-axis. Where M1 = 20 kg, M2=…

Q: A- An air conditioner compressor 134a at 4 bar, 20 °C and 6 m³/min which is steadily compressed to…

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A: Solution - Given data - F1 =2.12 KNF2 =1.25 KNM1 =0.540KN-mθ =tan-126 =18.43°

Q: of poin the acceleration (in m/s²) of point a

A: Given; Point R is accelerating with respect to, point at 10∠1800 m/s2.Intantaneous acceleration of…

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

Thickness of the plate is reduced from 40mm to 20mm
by succesive cold rolling passes using identical rolls of
diameter 600 mm. Assume that there is no change in
width. If the coefficient of friction b/w the rolls and the
workpiece is 0.1.
Determine the minimum number of passes required?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An aluminium strip with a cross section of 200 mm × 8 mm is being rolled with 25% reduction of area, using 400 mm diameter steel rolls. The tensile yield stress of aluminium is 0.28 kN/mm2. Calculate i) The angle subtended by the deformation zone at the roll center. ii) The minimum coefficient of friction between the workpiece and the rolls for an unaided bite to be possible.
A 300mm thick slab is being cold rolled using roll of 600mm diameter.If the coefficient of friction is 0.08. Determine the maximum possible reduction.
Estimate the roll force, F, and the torque for an AISI 1020 carbon-steel strip that is 200 mmwide, 10 mm thick, and rolled to a thickness of 7 mm. The roll radius is 200 mm, and itrotates at 200 rpm. Note that K = 530 MPa and n = 0.26.
Question 3A rolling operation on a 250 mm wide, 8 mm thick, 1112 cold rolled steel takes place using hardened steel rolls with a surface finish of 0.03 μm. The rolls have a diameter of 350 mm and rotates at 115 rpm. The final thickness of the plate is 6 mm and the entry speed of the plate is 1.8m/s Calculate: 3.1)The minimum coefficient of friction required, that will make the rolling operation possible. 3.2 The required roll force. 3.3 The position of the neutral point, ??3.4 Indicate, using a sketch, the neutral point showing all relevant notation and dimensions
In a rolling operation using a roll of diameter 1.5 m, if a 35 mm thick plate cannot be reduced to less than 12 mm in a single pass then calculate the coefficient of friction btween the rolls and the plate.
A metal strip is to be rolled from an initial wrought thickness of 3.5 mm to a final rolled thickness of 2.5 mm in a single pass rolling mill having rolls of 250 mm diameter. The strip is 450 mm wide. The average coefficient of friction in the roll gap is 0.08. Taking plane strain low stress of 140 MPa, for the metal and assuming negligible spreading, the roll separating force is.....
Bar stock of initial diameter = 90 mm is drawn with a draft = 15 mm. The draw die has an entrance angle = 18°, and the coefficient of friction at the work‑die interface = 0.08. The metal behaves as a perfectly plastic material with yield stress = 105 MPa. Determine (a) area reduction, (b) draw stress, (c) draw force required for the operation, and (d) power to perform the operation if exit velocity = 1.0 m/min
Correct Solution need.. Two parallel shafts, 61 cm apart and having a speed ratio of 3, are connected by cylinders in pure rolling contact. Determine the D1 in cm, when they turn in same directions.
A strip with cross section 120 X 6 mm is being rolled with 20 % reduction area, using rolls of 400mm diameter the coefficient of friction is 0.1 Determine the final strip thickness the angle of bite, length of deformation zone
Would you kindly answer this question A rolling operation on a 250 mm wide, 8 mm thick, 1112 cold rolled steel takes place using hardened steel rolls with a surface finish of 0.03 μm. The rolls have a diameter of 350 mm and rotates at 115 rpm. The final thickness of the plate is 6 mm and the entry speed of the plate is 1.8 m/s. Calculate: 3.1 The minimum coefficient of friction required, that will make the rolling operation possible. 3.2 The required roll force. 3.3 The position of the neutral point, ?? 3.4 Indicate, using a sketch, the neutral point showing all relevant notation and dimensions.
A single pass rolling process is used with 410 mm diameter steel rollers and a strip of width 140 mm and thickness of 8 mm undergoes 10% reduction of thickness. Calculate the angle of bite in radians?
In a single pass rolling process using 412mm diameter steel rollers, strip of width 120mm and thickness 8mm undergoes 10%reduction of thickness. The angle of bite in radians is.