Within few minutes 2 46. A thin square plate in biaxial stress is subjected to stresses ox and oy, as shown in part (a) of the figure. TEAnalysis of Stress and Strain 49width of the plate is bE, = 427 X 10-6 and= 300 mm. Measurements show that the normal strains in the x and y directions a113 × 10-6, respectively.%DEyWith reference to part (b) of the figure, which shows a two-dimensional view of the plate, determine thallowing quantities: (a) the increase Ad in the length of diagonal Od; (b) the change Ao in the angleTeen diagonal Od and the x axis; and (c) the shear strain y associated with diagonals Od and cf (that is, fimthe decrease in angle ced).lyde9.(a)(b)PROB. 46

Answered: Image /qna-images/answer/e006e95e-5d43-4c0e-ac9e-1a3efd9ccbcf.jpg

thin square plate in biaxial stress is subjected to stresses o, and oy, as shown in part (a) of the figure." = 300 mm. Measurements show that the normal strains in the x and 113 X 10-, respectively. of the plate is b 427 X 10-6 and Vith reference to part (b) of the figure, which shows a two-dimensional view of the plate, determine ing quantities: (a) the increase Ad in the length of diagonal Od; (b) the change Ao in the angle en diagonal Od and the x axis; and (c) the shear strain y associated with diagonals Od and cf (that is, f y directions crease in angle ced). Oy d 9. (a) (b)

thin square plate in biaxial stress is subjected to stresses o, and oy, as shown in part (a) of the figure." = 300 mm. Measurements show that the normal strains in the x and 113 X 10-, respectively. of the plate is b 427 X 10-6 and Vith reference to part (b) of the figure, which shows a two-dimensional view of the plate, determine ing quantities: (a) the increase Ad in the length of diagonal Od; (b) the change Ao in the angle en diagonal Od and the x axis; and (c) the shear strain y associated with diagonals Od and cf (that is, f y directions crease in angle ced). Oy d 9. (a) (b)

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 26 MPa, Sy = 75 MPa, and Sxy = 10 MPa. (a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) (c) Compute the absolute shear stress at the point.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 52 MPa, Sy = 63 MPa, and Sxy = 29 MPa.(a) Determine the principal stresses and the maximum in-plane shear stress acting at the point.(b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)(c) Compute the absolute shear stress at the point.
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 12.4 ksi, Sy = 3.5 ksi, and Sxy = 3.6 ksi. Assume β=29∘. Determine the normal stresses σx and σy and the shear stress τxy at the point.
Due to loading, the plate is deformed into the dashed shape shown in the figure. Assume a = 39 in., b= 33 in., δ1= 0.1625 in., δ2= 0.1 in. Determine the average normal strain along the side AB?in micro rad And answer in right and clear way Determine the average shear strain in the plate at A relative to the horizontal and vertical axes?
The rigid horizontal slab is attached to two identical copper rods. There is a gap Δ = 6.18 mm between themiddle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 81°C. Use the following data:
The stresses shown in the figure act at a point in a stressed body. The stress magnitudes are Sx = 170 MPa, Sy = 85 MPa, and Sxy = 45 MPa, acting in the directions indicated in the figure. Determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 48°.
In the shown diagram below, the curved out bar has an axis that is circular (with mean radius r = 12in) and is subjected to the m horizontal forces P = 400lb at the two ends. The cross-section of the bar is a triangular shape with height h and thickness t. If the allowable tensile stress in the bar is 12,000 psi, and height h=1.2 in, what's the minimum thickness tmin that is required?
A steel flat 10 cm wide and 2 cm thick is bent into a circular arc of 50m radius.Find the maximum intensity of stress induced. Take E = 2.05 * 10 ^ 5 N/mm².
The stress condition of an I-section beam at point A is given. (It is 30 MPA shear stress value.) a) Calculate the principal stresses, location and angle. b) Calculate the stress components that will affect the plane in a section a-a that makes a 30 degree angle shown in the figure.
50% Due to loading, the plate is deformed into the dashed shape shown in the figure. Assume a = 32 in., b= 40 in., δ1= 0.225 in., δ2= 0.075 in. Determine the average normal strain along the side AB? Determine the average shear strain in the plate at A relative to the horizontal and vertical axes?
Q) If the failure of shearing stress in a steel plate is 2,300KN, determine (a) the force required to punch a 32 mm diameter hole in a 10mm thick plate and, (b) the corresponding normal stress ina punch. Explain it correctly
Determine the stress at locations A, B, C, D, E and F (Figure 2). Show step by step