The stresses shown in the figure act at a point in a stressed body. The stress magnitudes are Sx = 170 MPa, Sy = 85 MPa, and Sxy = 45 MPa, acting in the directions indicated in the figure. Determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 48°. The stresses shown in the figure act at a point in a stressed body. The stress magnitudes are S = 170 MPa, S, = 85 MPa, and Sy = 45MPa, acting in the directions indicated in the figure. Determine the normal and shear stresses at this point on the inclined planeshown. Assume ß = 48°.S,SxyAnswer:! MPaSni! MPaSnt =i

Answered: Image /qna-images/answer/36b9222d-21f0-442c-8319-8e30fef442fc.jpg

The stresses shown in the figure act at a point in a stressed body. The stress magnitudes are S = 170 MPa, S, = 85 MPa, and Sy = 45 MPa, acting in the directions indicated in the figure. Determine the normal and shear stresses at this point on the inclined plane shown. Assume ß = 48°. S, Sxy Answer: ! MPa Sn i ! MPa Snt = i

The stresses shown in the figure act at a point in a stressed body. The stress magnitudes are S = 170 MPa, S, = 85 MPa, and Sy = 45 MPa, acting in the directions indicated in the figure. Determine the normal and shear stresses at this point on the inclined plane shown. Assume ß = 48°. S, Sxy Answer: ! MPa Sn i ! MPa Snt = i

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.1CTP: EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on...

See similar textbooks

Similar questions

EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 85 MPa and S, =- 200 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume B= 48°
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 23.6 ksi, Sy = 2.8 ksi, and Sxy = 7 ksi. Assume β=19∘. Determine the normal stresses σx and σy and the shear stress τxy at the point.
The couple M is applied to a beam of the cross-section shown in a plane forming an angle β withthe vertical y-axis. Determine the total normal stress at point A, point B, point D.
Determine the average axial tensile stress in the bar of the figure below if P=225 kN and the cross sectional area of the bar is 2500 square mm
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 60 MPa and Sy = 245 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 53°.
Determine the magnitude of the shear stress (in units of MPa) when the state of stress is oriented 45 degrees from the element shown (aligned with line AB).
Determine the shear stress at points A and B on the beam if it is subjected to ashear force of V = 400 kN. Represent the state of stress on a volume element of these points.
Using the equations for determination of stress at a point, calculate the value for the maximum shear stress that develops if the major principal stress is 7.2 ksi compression and the minor principal stress is 3.6 ksi tension.
Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kN force is applied to the ring at B, determine the angle ? so that the average normal stress in each rod is equivalent. What is this stress? (10)
For the beam shown below, b = 6 in and h = 14 in. If the beam is subjected to a transverse shear for of V = 8 kip, determine the largest shearing stress in the beam. Express your answer in psi to the nearest whole psi
The stresses shown act at a point on the free surface of a machine component. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 22.6 ksi, Sy = 2.2 ksi, and Sxy = 3.8 ksi. Assume β=33∘β=33∘. Determine the normal stresses σxσx and σyσy and the shear stress τxyτx⁢y at the point.