Three 100-2 resistors are connected as shown in100ΩFigure. The maximum power that can safely be100Ωdelivered to any one resistor is 50.0 W. What is themaximum voltage that can be applied to the100 2terminals a and b?68 voltA)106 voltB)74 volt56 voltD)82 voltE)

Answered: Image /qna-images/answer/06219a88-5a69-46bf-ae05-d67577b13fc5.jpg

Answered: Three 100-2 resistors are connected as…

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter18: Direct-Current Circuits

Section: Chapter Questions

Problem 51AP: When two unknown resistors are connected in series with a battery, the battery delivers 225 W and...

See similar textbooks

Similar questions

Check Your Understanding How would you use a river and two waterfalls to model a parallel configuration of two resistors? How does this analogy break down?
Semi-truck or trucks use four large 12-V batteries. The starter systemrequires 24 V, while normal operation of the truck’s other electrical components utilizes 12 V. How could the four batteries be connected to produce 24 V? To produce 12 V? Why is 24 V better than 12 V for starting the truck’s engine (a very heavy load)?
Resistors are commonly rated at 18W,14W,12W ,1 W and 2 W for use in electrical circuits. If a current of1 = 2.00 A is accidentally passed through a R=1.00 resistor rated at 1 W, what would be the most probable outcome? Is there anything that can be done to prevent such an accident?
Integrated Concepts A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg. °C, assuming no heat escapes?
Consider the circuit below. The battery has an emf of = 30.00 V and an internal resistance of r = 1,00 . (a) Find the equivalent resistance of the circuit and the current out of the battery. (b) Find the current through each resistor, (c) Find die potential drop across each resistor, (d) Find the power dissipated by each resistor, (e) Find the total power supplied by the batteries.
The power dissipated in a resistor is given by P = V2/R, which means power decreases if resistance increases. Yet this power is also given by P = I2R, which means power increases if resistance increases. Explain why there is no contradiction here.
Check Your Understanding Digital meters are able to detect smaller currents than analog meters employing galvanometers. How does this explain their ability to measure voltage and current more accurately than analog meters?
When a straight wire is heated, its resistance changes according to the equation R = R0 [1 + (T T0)] (Eq. 17.7), where is the temperature coefficient of resistivity. (a) Show that a more precise result, which includes the length and area of a wire change when it is heated, is R=R0[1+(TT0)][1+(TT0)][1+2(TT0)] where is the coefficient of linear expansion. (See Topic 10.) (b) Compare the two results for a 2.00-m-long copper wire of radius 0.100 mm, starting at 20.0C and heated to 100.0C.
In Figure 21.41. does the graph indicate the time constant is shorter for discharging than for charging? Would you expect ionized gas to have low resistance? How would you adjust R to get a longer time between flashes? Would adjusting R affect the discharge time?
Check Your Understanding If you place a wire directly across the two terminal of a battery, effectively shorting out the terminals, the battery will begin to get hot. Wiry do you suppose this happens?
When a straight wire is heated, its resistance changes according to the equation R = R0 [1 + (T T0)] (Eq. 17.7), where is the temperature coefficient of resistivity. (a) Show that a more precise result, which includes the length and area of a wire change when it is heated, is R=R0[1+(TT0)][1+(TT0)][1+2(TT0)] where is the coefficient of linear expansion. (See Topic 10.) (b) Compare the two results for a 2.00-m-long copper wire of radius 0.100 mm, starting at 20.0C and heated to 100.0C.
Three identical 60.0-W, 120-V lightbulbs are connected across a 120-V power source as shown in Figure P28.72. Assuming the resistance of each lightbulb is constant (even though in reality the resistance might increase markedly with current), find (a) the total power supplied by the power source and (b) the potential difference across each lightbulb.

SEE MORE QUESTIONS

Recommended textbooks for you

College Physics

Physics

ISBN:

9781285737027

Author:

Raymond A. Serway, Chris Vuille

Publisher:

Cengage Learning

College Physics

Physics

ISBN:

9781305952300

Author:

Raymond A. Serway, Chris Vuille

Publisher:

Cengage Learning

University Physics Volume 2

Physics

ISBN:

9781938168161

Author:

OpenStax

Publisher:

OpenStax

College Physics

Physics

ISBN:

9781285737027

Author:

Raymond A. Serway, Chris Vuille

Publisher:

Cengage Learning

College Physics

Physics

ISBN:

9781305952300

Author:

Raymond A. Serway, Chris Vuille

Publisher:

Cengage Learning

University Physics Volume 2

Physics

ISBN:

9781938168161

Author:

OpenStax

Publisher:

OpenStax

Physics for Scientists and Engineers: Foundations…

Physics

ISBN:

9781133939146

Author:

Katz, Debora M.

Publisher:

Cengage Learning

An Introduction to Physical Science

Physics

ISBN:

9781305079137

Author:

James Shipman, Jerry D. Wilson, Charles A. Higgins, Omar Torres

Publisher:

Cengage Learning

College Physics

Physics

ISBN:

9781938168000

Author:

Paul Peter Urone, Roger Hinrichs

Publisher:

OpenStax College

SEE MORE TEXTBOOKS

Three 100-2 resistors are connected as shown in 1002 Figure. The maximum power that can safely be 100 2 delivered to any one resistor is 50.0 W. What is the maximum voltage that can be applied to the 1002 terminals a and b? 68 volt A) 106 yolt B)