Three D.C. voltmeters are connected in series across a 120 V D.C. supply. The voltmeters are specified as follows: Voltmeter A: 100 V, 2.5 mA Voltmeter B: 100 V, 500 22/V Voltmeter C: 10 mA, 30000 92 The voltages read by the meters A, B and C are respectively. (a) 30, 40 and 50 V (b) 40, 50 and 30 V (c) 50, 40 and 30 V (d) 40, 30 and 50 V

Three D.C. voltmeters are connected in series across a 120 V D.C. supply. The voltmeters are specified as follows: Voltmeter A: 100 V, 2.5 mA Voltmeter B: 100 V, 500 22/V Voltmeter C: 10 mA, 30000 92 The voltages read by the meters A, B and C are respectively. (a) 30, 40 and 50 V (b) 40, 50 and 30 V (c) 50, 40 and 30 V (d) 40, 30 and 50 V

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter22: Resistive-capacitive Parallel Circuits

Section: Chapter Questions

Problem 6RQ: Refer to the formulas in Appendix B in the Resistive-Capacitive Parallel Circuits section. A...

See similar textbooks

Similar questions

Refer to the formulas in Appendix B in the Resistive-Capacitive Parallel Circuits section. A resistor and capacitor are connected in parallel to a 208-V, 60-Hz power source. An ammeter indicates a total circuit current of 46 amps, and a wattmeter indicates a true power of 4975 W. What is the resistance of the circuit?
voltmeter with resistance 'RV' is connected in parallel with resistance R=100 ohms. applied voltage V= 100V, Determine the error (E) & percentage error (% E) in the measurement of voltage (V) due to loading effect of voltmeter when- (i) RV=1M (Ohms) (ii) RV = 100K (Ohms).
A voltmeter of (0- 300V) and Ammeter of (0- 20A) are connected in a circuit to measure the value of power input to the circuit. Both the meters are found with a limiting error of 1.1% on half-scale deflection. Calculate the following, when the voltmeter and ammeter shows 230 V and 10 A respectively. i. Limiting eror voltage ii. Limiting error power
The circuit shows a variable resistor, with a lamp (L) connected to an ammeter and a voltmeter. By inspection, the circuit shown demonstrates that a) the variable resistor and voltmeter should be interchanged b) the lamp L and voltmeter should be interchanged c) the ammeter should be parallel with R, not with the lamp L d) the voltmeter and ammeter should be interchanged
Q13) The voltmeter can measures the voltage across resistive load. For a particular voltmeter, it exhibits error of 4.11% while measuring 363.5V. If so, calculate trure value of the voltmeter. a. 348.75V b. 340.28V c. 350.55V d. 355.51V
Assuming the batteries supply a potential difference of DeltaV = 3.0 V, and use Ohm's Law along with the total currents measured in circuits 4a, 4b and 4c to determine the equivalent resistance of each circuit. Please show the calculation of each.
Consider a PV Module with 8 PV cells with the Size of each 10cm x 5cm are connected in series. Calculate the following for the above Module. a. The output voltage is 4V, the output power is 6W b. The output voltage is 4V, the output power is 8W c. The output voltage is 8V, the output power is 1.5W d. The output voltage is 8V, the output power is 6W
Draw the below given circuit. Change value of components according to your circuit. Use ammeter, voltmeter and ohmmeter to measure the current, voltage and resistence. Use Norton's theorem to find the current flowing through R 2 resistor shown in figure. R1=35 N, R2=50 N, R3=30 N, R4=20 Q, R=10 N and V=70 volts.
The ammeter-voltmeter method is used to measure an unknown resistance R. An ammeter (A) connected in series with the resistance reads 0.3 R. A voltmeter (V) placed across the ends of the resistance reads 1.5V. compute the value of the resistance R.
Being the following circuit, to analyze only the effect of the Is or Vs sources, the resistances remain: a) Remain the same during the analysis b) short circuit c) closed circuit d) Open circuit
Breadboard Projects Propose a SIMPLE PROJECT with the use of Basic Electronic Components and Define why you’ve chosen/decided to propose that project? What is itsimportance? Requirements :Title of the Project:Its Importance:List of Components:Breadboard Layout:
Use the following circuit diagram of a DC parallel circuit for calculations. Known: VAB = 14 V, R1 = 56 Ohm, R2 = 84 Ohm, and R3 = 134 Ohm. Calculate I. Keep three decimals for accuracy. Hint: You can choose from two approaches.