•Three identical circular disks A, B and C are welded to the ends of three identical solid circular bars as shown in the figure below. The bars lie in a common plane and the disks lie in planes perpendicular to the axes of the bars. The bars are welded at their intersection D to form a rigid connection. Each bar has diameter di = 15 mm and each disk has diameter d₂ = 90 mm. Forces P1, P2 and P3 act on disks A, B and C respectively, thus subjecting the bars to torsion. If P₁ = 500 N, the maximum shear stress T max (in MPa) in any of the three bars is 135 D/135

•Three identical circular disks A, B and C are welded to the ends of three identical solid circular bars as shown in the figure below. The bars lie in a common plane and the disks lie in planes perpendicular to the axes of the bars. The bars are welded at their intersection D to form a rigid connection. Each bar has diameter di = 15 mm and each disk has diameter d₂ = 90 mm. Forces P1, P2 and P3 act on disks A, B and C respectively, thus subjecting the bars to torsion. If P₁ = 500 N, the maximum shear stress T max (in MPa) in any of the three bars is 135 D/135

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The outer diameter of the solid steel pipe shown in the figure is 25 mm. If the pipe is fixed at point E as in the figure andIt is subjected to a force of 800 N, a torque of 45 N.m and a moment of 300 N.m, applied from the other end of the pipe as in the figure.if left, it will occur at point A;(a) Principal planes (@p1, Opz),(b) Principal stresses (Omax, Omin),(c) the view of the principal plane, Note: Point A is on the top and outer surface of the steel pipe. The line AB is parallel to the z-axis andpassing through the center
An I shape cross-section is subjected to the moment M = 8.4 kN.m. Determine the stress at point A. Set θ = 28°. Present your answer in MPa. The moments of inertia are Iz = 31.846 x 106 mm4 and Iy = 3.346 x 106 mm4.
A beam supported by three identical springs at points A,B,C (see figure). Given that flexural of rigidity of the beam, EI= 2.029X1011 N.mm2 ; spring constant,k = 1471.5N/mm, w=116N/mm All dimensions are in mm. 1. What is the reaction for at point A,B and C? 2. What is the deflection at point B? 3. Please draw shear-force and bending moment diagram.
A rectangular beam is supported at both ends. It carries two concentrated load of 110kN, a clockwise moment of 110kN-m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 60GPa. Solve the following if the reaction at point B is 328.90256410256kN, upward. BEAM DIMENSION: Width = 190mm , Height = 390mm NOTE: b = 4.8m ; Determine the deflection at midspan
The beam shown in Figure Q.2 consists of a W610 × 140 structural steel wide-flange shape [E = 200 GPa; I = 1120 × 106 mm4]. If w = 64 kN/m and P = 126 kN , determine: Part A: The reactions at A, B, and D. Choose the reaction force at B as the redundant; therefore, the released beam is simply supported between A and D. a) Calculate the value of the deflection at point B due to uniformly distributed load w in the form ??=??????????? Note: EI will cancel out in further calculations. Enter the numerator in the answer box below in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
The shaft ABCD is bearing torques at pully A, B, C, and D as shown in the figure. The magnitude of the torques on each pully and the shaft length are given. All shafts are made of a material with a modulus of rigidity of G = 80 GPa. The diameter of shafts (1) and (2) is d1 = d2 = 52 mm, and the diameter of shafts (3) and (4) is d3 = d4 = 58 mm. The bearings shown allow the shaft to turn freely. [TA = 1399 N-m, TB = 4585 N-m, TC = 2649 N-m, TD = 537 N-m, a = 0.35 m, b = 0.45 , c = 0.2 m, d = 0.35 m] Determinethe internal torque in segment (1) of the shaft.in N.m Determinethe internal torque in segment (2) of the shaft.in N.m Determinethe internal torque in segment (3) of the shaft.in N.m
The shaft ABCD is bearing torques at pully A, B, C, and D as shown in the figure. The magnitude of the torques on each pully and the shaft length are given. All shafts are made of a material with a modulus of rigidity of G = 80 GPa. The diameter of shafts (1) and (2) is d1 = d2 = 52 mm, and the diameter of shafts (3) and (4) is d3 = d4 = 58 mm. The bearings shown allow the shaft to turn freely. [TA = 1399 N-m, TB = 4585 N-m, TC = 2649 N-m, TD = 537 N-m, a = 0.35 m, b = 0.45 , c = 0.2 m, d = 0.35 m] Determinethe internal torque in segment (1) of the shaft. Determinethe internal torque in segment (2) of the shaft. Determinethe internal torque in segment (3) of the shaft.
Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that the weight of the plate is negligible, and that the horizontal force F, as well as the reactions Dy and Dx in the joint D balance the plate shown in the figure. Note: the x-axis is horizontal and the y-axis is vertical and both have their origin at point D. Data: P = 332N If the plate had a weight of 332N (applied vertically downwards in the center of the plate), the module of F should be greater than 369.18N, so that it would still remain balanced in that position?
Refer to the figure, what is the horizontal component of the reaction at pin B in kN?
QUESTION 4: The cylindrical shaft given in the figure is made of two different sectioned elements between A-Cara and C-D. A torque of 700 Nm is applied in the direction indicated from point B. Since the stiffness modulus (G) of the shaft material is 80 MPa, calculate the support reactions at the A and D ends.
In the cage system given in the figure, AB, DE andPressure or pull CB rod forcescalculate by stating that they are. L1(m)=2.1 ,L2(m)=3.2, P1(kN)=65, P2(kN)=57
There is a structure composed of beam (AC) and truss (BD) as shown in the figure below. After trying to calculate the force: (1) the vertical displacement of point C, (2) if you want to extend (or shorten) the truss (BD) in advance To offset the displacement of point C, what is the amount of elongation (or shortening)? Assuming that the E of the entire structural section is 29,000 kips/inch^2, the I of the beam (AC) section is 340 in^4, and the truss (BD) section A is 5 in^2