Three identical resistors (R) are connected in a circuit so that two are in series and the third is in parallel with the combination of the first two. If connected to a battery individually, each resistor dissipates power P. Determine the power dissipated by the network combination when connected to the same source.

Three identical resistors (R) are connected in a circuit so that two are in series and the third is in parallel with the combination of the first two. If connected to a battery individually, each resistor dissipates power P. Determine the power dissipated by the network combination when connected to the same source.

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 37P: Consider the circuits shown below, (a) What is the current through each resistor in part (a)? (b)...

See similar textbooks

Similar questions

The hot resistance of a flashlight bulb is 2.30 , and it is run by a 1.58-V alkaline cell having a 0.100-O internal resistance. (a) What current flows? (b) Calculate the power supplied to the bulb using I2Rbulh? (c). power the same as calculated using V2Rbulb?
Consider the circuits shown below, (a) What is the current through each resistor in part (a)? (b) What is the current through each resistor in part (b)? (c) What is the power dissipated or consumed by each circuit? (d) What is the power supplied to each circuit?
What is die basic operation of an ohmmeter as it measures a resistor?
(a) Find the terminal voltage of a 12.0-V motorcycle battery having a 0.600- internal resistance, if it is being charged by a current of 10.0 A. (b) What is the output voltage of the battery charger?
Consider the circuit shown in the preceding problem. Write equations for the power supplied by the voltage sources and the power dissipated by the resistors in terms
Why is the following situation impossible? A technician is testing a circuit that contains a resistance R. He realizes that a better design for the circuit would include a resistance 73R rather than R. He has three additional resistors, each with resistance R. By combining these additional resistors in a certain combination that is then placed in series with the original resistor, he achieves the desired resistance.
Referring to the example combining series and parallel circuits and Figure 21.6, calculate I3in the following two different ways: (a) from the known values of I and I2 ; (b) using Ohm’s law for R3. In both parts explicitly show how you follow the steps in the Problem-Solving Strategies for Series and Parallel Resistors.
Integrated Concepts (a) An immersion heater utilizing 120 V can raise the temperature of a 1.00 102 -g aluminum cup containing 350 g of water from 20.0°C to 95.0°C in 2.00 min. Find its resistance, assuming it is constant during the process. (b) A lower resistance would shorten the heating time. Discuss the practical limits to speeding the heating by lowering the resistance.
Find the currents flowing in the circuit in Figure 21.52. Explicitly show how you follow the steps in the Problem-Solving Strategies for Series and Parallel Resistors.
Two lightbulbs are each connected to a voltage of 120 V. One has a power of 25 W, the other 100 W. (a) Which lightbulb has the higher resistance? (b) Which lightbulb carries more current?
(a) Haw much power is dissipated in a short circuit of 240-V AC through a resistance of 0.250 ? (b) What current flows?
A person with body resistance between his hands of 1.00 k accidentally grasps the terminals of a 20.0-kV power supply. (Do NOT do this!) (a) Draw a circuit diagram to represent the situation. (b) If the internal resistance of the power supply is 2000 , what is the current through his body? (c) What is the power dissipated in his body? (d) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in this situation to be 1.00 mA or less? (e) Will this modification compromise the effectiveness of the power supply for driving low-re si stance devices? Explain your reasoning,