Three impedances Z1, Z2 and Z3 are connected in tee. The impedance Z1 is connected in series with the supply voltage V1 while the impedance Z2 is connected in series with the voltage V2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5+j4) ohms, Z2 = (10-j13) ohms, and Z3 = 15 bar angle of 15° ohms, calculate the currrent flowing in each impedance. Use Superposition theorem

Three impedances Z1, Z2 and Z3 are connected in tee. The impedance Z1 is connected in series with the supply voltage V1 while the impedance Z2 is connected in series with the voltage V2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5+j4) ohms, Z2 = (10-j13) ohms, and Z3 = 15 bar angle of 15° ohms, calculate the currrent flowing in each impedance. Use Superposition theorem

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.45P: Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at...

See similar textbooks

Similar questions

Three impedances Z1, Z2 and Z3 are connected in tee. The impedance Z1 is connected inseries with the supply voltage V1 while the impedance Z2 is connected in series with the voltageV2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5+j4) ohms, Z2 = (10-j13) ohms, and Z3 = 15 bar angleof 15° ohms, calculate the currrent flowing in each impedance. Use Nodal analysis.
Three impedances Z1, Z2 and ZL are connected in tee. The impedance Z1 is connected in series with the supply voltage V1 while the impedance Z2 is connected in series with the voltage V2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5+j4) ohms, Z2 = (10-j13) ohms, and ZL. Calculate the maximum power transferred to load impedance ZL . Use Maximum power transfer theorem.
Q4. The source current in the circuit shown is in Figure 3a) What impedance should be connected across terminals a,b for maximum average powertransfer?b) What is the average power transferred to the impedance in (a)?c) Assume that the load is restricted to pure resistance. What size resistor connected across a,bwill result in the maximum average power transferred?d) What is the average power transferred to the resistor in (c)?v
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
In a house there is a three-wire system configured as follows. A refrigerator with an impedance of (10 + j 10) Ω is connected to line L1 and to neutral, and to line L2 and neutral all the lighting in the house consists of 10 luminaires of 20 W each. In addition, there is a 240 V dryer that consumes 8 kW. Calculate a) current of line L1 and line L2 and neutral b) total power consumed.
If all impedances in Figure Q2 are 15+j45 Ω. Calculate the neutral line current.
Two resistors Ra and Rb, are connected in parallel, Ra having a value of 33.40909 ohms and Rb being adjustable over a wide range. The parallel combination is then connected through a 105 ohm line resistor to a 211-volt source. If Rb is adjusted so that the power of Ra will be maximum, how many watts will Ra takes under this condition?
For the mutual electric circuit shown in figure beside, find the set values of mesh currents 11 &12? * 10020, Volt -19Q i1=22.1-j7.4 Ai2=5.96-j0.01 A i1=22.1-j7.4 Ai2=5.96+j0.01 A i1=22.14j7.4 Ai2=5.96-j0.01 A O OO0O0 i1=22.14j7.4 Ai2=5.96+j0.01 A
A resistor, in series with a 138-microfarad capacitor, is connected to a 60-cycle source.If the voltage drop across the capacitor is 115 volts and the power taken by the circuitis 922 watts, calculate (a) the circuit current, (b) the ohmic value of the resistor, (c) theline voltage, (d) the circuit power factor. draw the circuit diagram
Two loads connected according to the diagram below are connected to a three-phase network. All impedance elements are pure resistances and the two three-phases are symmetrical. Voltmeter V1 shows 250 V and voltmeter V2 shows 433 V. a) Calculate the voltage between L1 and L2 b) Calculate the current ID . c) Calculate the current IL . d) How big is cosφ1
1 Ia = ?? A 2.ib= ?? A 3 Vx = ?? 4 power at Rx = ?? 5 power at Rb = ??
A substation rated 1250 kVA is operating at full-load at 0.8 pf lagging and to carry an additional load of 170 kW at 0.85 pf lagging. With the mentioned power factor, the substation is experiencing inefficient electrical system: high power losses, high voltage drops in the electrical equipment, and high electricity bill. To reduce power losses and to reduce the electricity bill, power factor correction is to be of high importance and consideration. Find: power phasor diagram. computation of the following: additional substation capacity in KVA shunt capacitor KVA. Which alternative is more economical if cost/kVA of additional substation capacity is $400.00 and the cost/kVA of shunt capacitor is $180?