Q4. The source current in the circuit shown is in Figure 3a) What impedance should be connected across terminals a,b for maximum average powertransfer?b) What is the average power transferred to the impedance in (a)?c) Assume that the load is restricted to pure resistance. What size resistor connected across a,bwill result in the maximum average power transferred?d) What is the average power transferred to the resistor in (c)?v Q4. The source current in the circuit shown is in Figure 3a) What impedance should be connected across terminals a,b for maximum average powertransfer?b) What is the average power transferred to the impedance in (a)?c) Assume that the load is restricted to pure resistance. What size resistor connected across a,bwill result in the maximum average power transferred?d) What is the average power transferred to the resistor in (c)?3.6 mHa{20 N:5 μF4 NFigure 3

Solution: Assuming the source current as 10 A with the frequency as 50 Hz.…

Q4. The source current in the circuit shown is in Figure 3 a) What impedance should be connected across terminals a,b for maximum average power transfer? b) What is the average power transferred to the impedance in (a)? c) Assume that the load is restricted to pure resistance. What size resistor connected across a,b will result in the maximum average power transferred? d) What is the average power transferred to the resistor in (c)? 3.6 mH 202 5 μF 4Ω

Q4. The source current in the circuit shown is in Figure 3 a) What impedance should be connected across terminals a,b for maximum average power transfer? b) What is the average power transferred to the impedance in (a)? c) Assume that the load is restricted to pure resistance. What size resistor connected across a,b will result in the maximum average power transferred? d) What is the average power transferred to the resistor in (c)? 3.6 mH 202 5 μF 4Ω

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and current relationships change? (a) If C1 is the complex positive-sequence voltage gain in Problem 3.29 and (b) if C2 is the negative sequence complex voltage gain, express the relationship between C1andC2
Discuss the concept of electrical load balancing and its importance in power distribution.
Discuss Potential barriers of combined heat and power (CHP).
Why in high voltage system, we prefer direct or small resistance? How to define the classes of load? Why we should to do such classification??(find answer from website) what are the main load curves of the power system? What is the maximum load utilization hours? What are the applications of load curve and annual load curve in the design and operation of power system? (find answer from website)
Wiat is the difference between a real independent voltage source and an ideal independent voltage source? Give an example of a real voltage source and explain how it differs from the ideal.
Describe real and reactive power regulation
Variation of which of the following parameter is not consider as power quality problem for industry?VoltageCurrentPowerFrequency
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
5 b) What is reactive power compensationExplain how reactive power compensation is made and its benefits.
Discuss the concept of power system stability and the factors that influence it.
q1: Discussion of power quality aspects that need to be considered before installing the power factor correction unit
Power System analysis subject